2004 Hyundai Terracan od light indicator

FEATURES OF YOUR HYUNDAI
1- 6 B040B01A-AAT Locking and Unlocking Front Doors With a Key
B040B01HP
LOCK
UNLOCK
B040A01A-AAT DOOR LOCKS WARNING:
o Unlocked doors can be dangerous. Be-
fore you drive away (especially if there are children in the car), be sure that all thedoors are securely closed and locked sothat the doors cannot be inadvertentlyopened from the inside. This helps ensurethat the doors will not be opened acciden-tally. Also, when combined with the properuse of seat belts, locking the doors helpskeep occupants from being ejected fromthe car in case of an accident.
o Before opening the door, always look for and avoid oncoming traffic.
B030C01Y-AAT ILLUMINATED IGNITION SWITCH Whenever a door is opened, the ignition switch will be illuminated for your convenience, provid-ed the ignition switch is not in the "ON" position.The light will go off approximately 10 secondsafter closing the door or when the ignition switchis turned on.
B030C01E
NOTE: You can get the limp home password whenthe vehicle is first delivered to you. If you donot have the password, consult your autho-rized Hyundai dealer.
1. To set the password you may turn the ignition
key "ON" and then turn it "OFF" according to the digit numbers, then the immobilizer indi-cator will blink along with the operation of theignition key. For example, turn the ignition keyonce for digit number "1", and twice for "2",and so on. However, for the digit number "0",you must turn the ignition key for 10 times.
2. Wait for 3~10 seconds.
3. You may set the remaining number of digits by following the same procedures 1 and 2.
4. If all of four digits have been tried success- fully, turn the ignition key "ON" and check thatthe immobilizer indicator illuminates. Fromthis time, you have to start your engine within30 seconds. If you start your engine after 30seconds, your engine will not start.
NOTE:If the engine dies while driving after limphome procedure, you can start your enginewithin 8 seconds without limp home proce-dure again.
5. If the immobilizer indicator blinks for five seconds, you have to try the limp home procedure again from the beginning. After doing the limp home procedure, you have toconsult with your authorized Hyundai dealer assoon as possible. CAUTION:
o If you fail to try the limp home procedure
with the sequence of three times, youhave to wait for about one hour to do thelimp home procedure again.
o If you cannot start your engine in spite of limp home procedure, have your vehicletowed by an authorized Hyundai dealer.

FEATURES OF YOUR HYUNDAI
1- 36
B261A02HP-GAT INDICATOR AND WARNING LIGHTS (GASOLINE ENGINE) B260A01HP-1
11
23 4 5
6 7 8 910 11 1213 14
15 1617
18
19
1. Turn Signal Indicator Light
2. ABS Service Reminder Indicator Light (If installed)
3. Supplemental Restraint (AirBag) System Service Reminder lndicator (SRI) Light(If installed)
4. Low Oil Pressure Warning Light
5. Parking Brake/Low Brake Fluid Level Warning Light 6. Charging System Warning Light
7. A/T Oil Temperature Warning Light
(If installed)
8. Overdrive Off Indicator Light (If installed)
9. High Beam Indicator Light
10. Front Fog Indicator Light
11. Automatic Transmission Position Indicator Light (If installed)
12. Cruise Indicator Light (If installed) 13. 4WD LOW Indicator Light
14. 4WD HIGH Indicator Light (Part-time 4WD)
/4WD System Warning Light (Full-time 4WD)
15. Malfunction Indicator Light (MIL)
16. Tailgate Open Warning Light
17. Door Ajar Warning Light
18. Seat Belt Warning Light (If installed)
19. Low Fuel Warning Light
Part-time 4WD :Full-time 4WD :

FEATURES OF YOUR HYUNDAI
1- 38
B260A02HP-1
B264A02HP-GAT INDICATOR AND WARNING LIGHTS (DIESEL ENGINE)
1
2 34 67
8
910 11 12 13 14 17 18
19 202122
1
15
1. Turn Signal Indicator Light
2. Diesel Preheat Indicator Light
3. ABS Service Reminder Indicator Light
(If installed)
4. Supplemental Restraint (AirBag) System Service Reminder Indicator (SRI) Light(If installed)
5. Immobilizer Warning Light (2.9 CRDi only) (If installed)
6. Fuel Filter Warning Light 7. Low Oil Pressure Warning Light
8. Brake Vacuum Warning Light
9. Parking Brake/Low Brake Fluid Level
Warning Light
10. Charging System Warning Light
11. A/T Oil Temperature Warning Light (If installed)
12. Overdrive Off Indicator Light (If installed)
13. High Beam Indicator Light
14. Front Fog Indicator Light 15. Automatic Transmission Position Indicator
Light (If installed)
16. Cruise Indicator Light (If installed)
17. 4WD LOW Indicator Light
18. 4WD HIGH Indicator Light (Part-time 4WD) /4WD System Warning Light (Full-time 4WD)
19. Malfunction Indicator Light (MIL) (If installed)
20. Tailgate Open Warning Light
21. Door Ajar Warning Light
22. Seat Belt Warning Light (If installed)
23. Low Fuel Warning Light
Part-time 4WD :Full-time 4WD :
5
23
16

FEATURES OF YOUR HYUNDAI 1- 39
B260P02Y-GAT
ABS Service Reminder Indicator Light (If installed)
When the key is turned to the "ON" position, the Anti-Lock Brake System SRI will come on andthen go off in a few seconds. If the ABS SRIremains on, comes on while driving, or does notcome on when the key is turned to the "ON"position, this indicates that there may be a prob-lem with the ABS.If this occurs, have your vehicle checked by yourHyundai dealer as soon as possible. The normalbraking system will still be operational, but with-out the assistance of the anti-lock brake system. WARNING: If both ABS SRI and Parking Brake/Brakefluid level warning lights remain "ON" orcome on while driving, there may be a prob-
lem with E.B.D. (Electronic Brake Force Dis-tribution).If this occurs, avoid sudden stops and haveyour vehicle checked by your Hyundai dealeras soon as possible. B260F01A-AAT
High Beam Indicator Light
The high beam indicator light comes on when-ever the headlights are switched to the highbeam or flash position.
B260D01A-AAT Turn Signal Indicator Lights
The blinking green arrows on the instrument panel show the direction indicated by the turnsignals. If the arrow comes on but does not blink,blinks more rapidly than normal, or does notilluminate at all, a malfunction in the turn signalsystem is indicated. Your dealer should be con-sulted for repairs. B260G01A-AAT
Low Oil Pressure Warning Light
CAUTION: If the oil pressure warning light stays on while the engine is running, serious enginedamage may result. The oil pressure warninglight comes on whenever there is insufficientoil pressure. In normal operation, it shouldcome on when the ignition switch is turnedon, then go out when the engine is started.If the oil pressure warning light stays onwhile the engine is running, there is a seriousmalfunction. If this happens, stop the car as soon as it is safe to do so, turn off the engine and checkthe oil level. If the oil level is low, fill engine oilto the proper level and start the engine again.If the light stays on with the engine running,turn the engine off immediately. In any in-stance where the oil light stays on when theengine is running, the engine should bechecked by an authorized Hyundai dealerbefore the car is driven again.B260C01A-AAT O/D OFF Indicator (If Installed)
When the overdrive switch is turned on, the overdrive off indicator will go out. This amberindicator will be illuminated when the overdriveswitch is turned off.
B260H02A-GAT
Parking Brake/Low Brake Fluid Level Warning Light
WARNING: If you suspect brake trouble, have your brakeschecked by a Hyundai dealer as soon aspossible. Driving your car with a problem ineither the brake electrical system or brakehydraulic system is dangerous, and couldresult in a serious injury or death. Warning Light Operation The parking brake/brake fluid level warning light should come on when the parking brake is ap-plied and the ignition switch is turned to "ON" or"START". After the engine is started, the lightshould go out when the parking brake is re-leased.If the parking brake is not applied, the warninglight should come on when the ignition switch isturned to "ON" or "START", then go out when theengine starts. If the light comes on at any othertime, you should slow the vehicle and bring it toa complete stop in a safe location off the road-way.

FEATURES OF YOUR HYUNDAI
1- 40
B260M01A-AAT Low Fuel Level Warning Light
The low fuel level warning light comes on when the fuel tank is approaching empty. When itcomes on, you should add fuel as soon aspossible. Driving with the fuel level warning lighton or with the fuel level below "E" can cause theengine to misfire and damage the catalytic con-verter.
B260E01HP-GAT Seat Belt Warning Light (If Installed)
The seat belt warning light blinks for about 6 seconds when the ignition key is turned from the"OFF" position to "ON" or "START".
B260L01A-GAT
Door Ajar Warning Light
The door ajar warning light warns you that a door is not completely closed.
B260A01B-GAT Front Fog Indicator Light
Front fog indicator light comes on whenever the fog light switch is on.
B260Q01HP-DAT Cruise Indicator Light (If Installed)
The cruise indicator light in the instrument cluster is illuminated only when the vehicle cruisingspeed has been set using the control switch onthe steering wheel.The indicator light does not illuminate when themain cruise control switch is activated.Information on the use of cruise control may befound on page 1-64.
The brake fluid level warning light indicates thatthe brake fluid level in the brake master cylinderis low and hydraulic brake fluid conforming toDOT 3 or DOT 4 specifications should be added.After adding fluid, if no other trouble is found, thecar should be immediately and carefully driven toa Hyundai dealer for inspection. If further troubleis experienced, the vehicle should not be drivenat all but taken to a dealer by a professionaltowing service or some other safe method.Your Hyundai is equipped with dual-diagonalbraking systems. This means you still have brak-ing on two wheels even if one of the dual systemsshould fail. With only one of the dual systemsworking, more than normal pedal travel andgreater pedal pressure are required to stop thecar. Also, the car will not stop in as short adistance with only half of the brake system work-ing. If the brakes fail while you are driving, shift toa lower gear for additional engine braking andstop the car as soon as it is safe to do so.
B260J01S-GAT
Charging System Warning Light
The charging system warning light should come on when the ignition is turned on, then go outwhen the engine is running. If the light stays onwhile the engine is running, there is a malfunctionin the electrical charging system. If the lightcomes on while you are driving, stop, turn off theengine and check under the hood. First, makecertain the generator drive belt is in place. If it is,check the tension of the belt.And then, have the system checked by yourHyundai dealer. CAUTION: If the drive belt (generator belt) is loose,broken, or missing while the vehicle is driv-ing, there may be a serious malfunction, en-gine could overheat because this belt alsodrives the water pump. B260K01B-GAT
Tail gate Open Warning Light
This light remains on unless the tail gate iscompletely closed and latched.

FEATURES OF YOUR HYUNDAI 1- 41
B260T01HP-GAT
4WD HIGH Indicator Light (Part-time 4WD only)
When the key is turned to the "ON" position, the 4WD(Four Wheel Drive) HIGH indicator light willcome on and then go off in a few seconds.The 4WD HIGH indicator light will illuminatewhen the transfer shift knob is set to 4H position. CAUTION: If the 4WD HIGH indicator light ( )illuminates with the 4WD LOW indicator light( ) while driving, this indicates that thereis a malfunction in the 4WD system. If thisoccurs, have your vehicle checked by anauthorized Hyundai dealer as soon as pos-sible.
B260N01A-AAT
Malfunction Indicator Light (If installed)
This light illuminates when there is a malfunction of an exhaust gas related component, and thesystem is not functioning properly so that theexhaust gas regulation values are not satisfied.This light will also illuminate when the ignition keyis turned to the "ON" position, and will go out in afew seconds. If it illuminates while driving, or doesnot illuminate when the ignition key is turned to the"ON" position, take your car to your nearestauthorized Hyundai dealer and have the systemchecked.
B260R01HP-GAT 4WD LOW Indicator Light
When the key is turned to the "ON" position, the
4WD(Four Wheel Drive) LOW indicator light willcome on and then go off in a few seconds.
The 4WD LOW indicator light comes on when thetransfer shift knob is set to low position (Part-time4WD type : 4L position, Full-time 4WD type :LOW position).
B260B01A-AAT
SRS (Airbag) Service Reminder Indicator (SRI) Light(If installed)
The SRS service reminder indicator (SRI) comes on and flashes for about 6 seconds after theignition key is turned to the "ON" position or afterthe engine is started, after which it will go out. This light also comes on when the SRS is not working properly. If the SRI does not come on, orcontinuously remains on after flashing for about6 seconds when you turned the ignition key to the"ON" position or started the engine, or if it comeson while driving, have the SRS inspected by anauthorized Hyundai Dealer.B265T01HP-GAT 4WD System Warning Light (Full-time 4WD only)
When the key is turned to the "ON" position, the 4WD (Four wheel drive) system warning light willcome on and then go off in a few seconds. CAUTION: If the 4WD system warning light ( ) blinkswhile driving, this indicates that there is amalfunction in the 4WD system. If this oc-curs, have your vehicle checked by an autho-rized Hyundai dealer as soon as possible.
B260U01HP-DAT A/T(Automatic Transmission)
Oil Temperature Warning Light(If installed)
The A/T oil temperature warning light comes on when the automatic transmission oil temperaturegoes up to the temperature that may result inserious damage of automatic transmission.If the A/T oil temperature warning light comes onwhile driving, park your vehicle in at a safe place
as soon as possible. With the selector levershifted into "P" position, allow the engine to idleuntil the warning light goes off. When the warninglight goes off, the vehicle can be driven normally.
A/T

FEATURES OF YOUR HYUNDAI 1- 45
B990A01HP-GAT MULTIMETER(If installed)
1. Digital Clock
2. Azimuth Compass
3. Altimeter/Relative altimeter/Barometer
4. Azimuth adjustment switch5. Up switch
6. Down switch
7. Road display responsive to vehicle speed
8. Mode conversion switch
9. Light switch
1
23
456 7 8 9 B990B01HP-GAT HOW TO ADJUST MULTIMETER Switch function
Switch
Mode
(Up),
(Down) LightAdjust Function
Selecting of time adjustment mode (more than 2 sec)Altimeter correctionSetting altitude to "0"Time adjustmentIllumination on/off Selecting correction mode of azimuth indicator
B990C01HP-GAT Electrical azimuth compass
B990C01HP
B990A01HP
Azimuth Comass
Altimeter Relative Altimeter
Barometer

FEATURES OF YOUR HYUNDAI 1- 47
When you want to know the difference of altitude between the destination and the starting point.
1. Press the " (UP)" and " (DOWN)" switchsimultaneously for more than 1 sec to reset the current altitude to 0m.
2. After arriving, the displayed altitude is the difference of altitude between the destinationand the starting point.
Destination
B990E02HP
B990F01HP-GAT BAROMETER The current air pressure is displayed in hpa units
where the measurement range is from 720hpa to1,045hpa.(The minimum is 1hpa)If the "MODE" switch is pressed for less than 2sec from "Relative Altimeter" mode, the atmo-spheric pressure will be displayed on the displaywindow.
B990F01HP
B990G01HP-GAT DIGITAL CLOCK If you press "MODE" switch for more than 2 sec, the mode that you can adjust the time is dis-played. How to adjust the time
1. In time adjustment mode, push the "MODE" switch briefly, and you can adjust "minute". And if you push "MODE" switch once more
briefly, you can adjust "hour".
2. Adjust the time by pushing " (UP)"," (DOWN)" switch when the time blinks.
3. After adjusting the time, push "MODE" switch for more 2sec, and the mode for adjusting thetime is cancelled. B990G01HP
B990H01HP-GAT ROAD DISPLAY RESPONSIVE TO VE- HICLE SPEED
B990H01HP
The road display indicator blinks according to the vehicle speed.Vehicle speed
Below 2.8 km/h
2.8 ~ 40 km/h
41 ~ 60 km/h 61 ~ 80 km/h
81 ~ 100 km/h
Above 100 km/h Blinking cycle
Total Lightening
1 sec
0.8 sec0.5 sec 0.3 sec0.2 sec
The difference of altitude between the destinationand the starting point : 1000 m
Starting point