2004 Hyundai Matrix lock

FEATURES OF YOUR HYUNDAI
1- 10 B080F01S-AAT Seat Cushion Height Adjustment (Driver's Seat Only) (If Installed) To raise or lower the front part of the seat cushion, turn the front knob forward or rear-ward. To raise or lower the rear part of the seatcushion, turn the rear knob forward or rearward.
HFC2026
B080G01FC-GAT
UNDER TRAY (If Installed) The tray is located under the front passenger seat. It is opened by up and pulling forward. WARNING: To avoid the possibility of injury in case ofan accident or a sudden stop, the tray shouldbe kept closed when the car is in motion.
HFC2059
B080E01O-AAT Lumbar Support Control (Driver's Seat Only) (If Installed)
HFC2027To adjust the lumbar support, turn the handle on the outboard or left side of the seat. Toincrease the amount of lumbar support, pull thelever forward. To decrease it, push the levertoward the rear.
To raise the headrest, pull it up. To lower it, pushit down while pressing the lock knob. WARNING:
o For maximum effectiveness in case of an
accident, the headrest should be adjust-ed so the top of the headrest is at thesame height as the top of the occupant'sears. The use of a cushion that holds thebody away from the seatback is not rec-ommended.
o Do not operate the vehicle with the headrests removed as severe injury toan occupant may occur in the event ofan accident. Headrests may provide pro-tection against severe neck injurieswhen properly adjusted.

FEATURES OF YOUR HYUNDAI 1- 11
B090A01FC
Lock Knob
B090A01FC-GAT
Adjustable Headrests (If Installed) Headrests are designed to help reduce the risk of neck injuries.To raise the headrest, pull it up. To lower it,push it down while pressing the lock knob. WARNING:
o For maximum effectiveness in case of an
accident, the headrest should be adjustedso the top of the headrest is at the sameheight as the top of the occupant's ears.The use of a cushion that holds the bodyaway from the seatback is not recom-mended.
o Do not operate vehicle with the head- rests removed as severe injury to anoccupant may occur in the event of anaccident. Headrests may provide protec-tion against severe neck injuries whenproperly adjusted.
B080I01FC-BAT Adjusting Seatback Angle
HFC2061
To move the seat toward the front or rear, pull the lock release lever upward. This will releasethe seat on its track so you can move it forwardor rearward to the desired position. When youfind the position you want, release the lever andslide the seat forward or rearward on its trackuntil it locks into the desired position and can-not be moved further.
B080H01FC-GAT REAR SEAT Adjusting Seat Forward and Rearward
HFC2060To recline the seatback, push the seatback folding lever toward the headrest, and releaseit after the desired seatback angle is achieved.When you recline the seatback to desired posi-tion, always be sure it has locked into position. CAUTION: When reclining the seatback angle, youshould be adjust the seatback folding leverwith standing.
Seatbackfolding lever

FEATURES OF YOUR HYUNDAI
1- 12 5. To secure the seat, hook the securing strap
under the seat cushion to the headrest stay of front driver and passenger seat.
6. Insert the removed headrests between the seatback and seat cushion, so that they willnot be thrown forward in the case of asudden stop or an accident.
7. To return the seatback and seat cushion to its normal position, reverse the above pro-cedure.
o When you return the seatback to its upright position, always be sure it is locked intoposition by pulling and pushing on the top ofseatback.
WARNING:
o When you return the folded down seat back to its upright position, make surethe seat belts are in position to be acces-sible and to function properly.
o The purpose of the fold down rear seat back and the fold forward rear seat cush-ion is to increase cargo space. Do notallow passengers to sit in the cargo areawhile the car is moving. This is not aproper seating position and no seat beltsare available for use when the seat backis folded down. Passengers who are notproperly seated and wearing seat beltscould sustain serious injuries or death incase of an accident or a sudden stop.
o Objects should not extend higher than the top of the front seatbacks. This couldallow cargo to slide forward and causeinjury or damage during sudden stops.
4. Pull the seat cushion release lever upward,
then fold up the seat cushion.
CAUTION:To prevent damage, ensure that the reardrinkholder, located in the rear console, isclosed before folding the rear seatback andseat cushion.
HFC2075
HFC2076
Seat cushion release lever
Securing strap
B090B01FC-GAT Folding Rear Seatback and Seat Cushion For greater convenience, the entire seatback and seat cushion may be folded down and up.
HFC2074
1. Move the rear seat to the rearmost position.
2. Remove the headrests.
3. To fold down the seatback , push and hold the seatback folding lever toward the head-rest, then push down the seatback.
Seatback folding lever

FEATURES OF YOUR HYUNDAI 1- 15
B170A01E
STA1090P
B180A02A-GAT SEAT BELTS 3-Point System with Emergency Locking Retractor (If Installed)To Fasten Your Belt To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle.There will be an audible "click" when the tablocks into the buckle.The seat belt automatically adjusts to the properlength only after the lap belt is adjusted manu-ally so that it fits snugly around your hips. If youlean forward in a slow, easy motion, the belt willextend and let you move around. If there is asudden stop or impact, however, the belt will
B170A04A-AAT HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT (If Installed) You can adjust the height of the shoulder belt anchor to one of the 4 positions for maximumcomfort and safty.If the height of the adjusting seat belt is too nearyour neck, you will not be getting the mosteffective protection. The shoulder portion shouldbe adjusted so that it lies across your chest andmidway over your shoulder nearest the doorand not your neck.To adjust the height of the seat belt anchor,lower or raise the height adjuster into an appro-priate position. To raise the height adjuster, pullit up. To lower it, push it down while pressing theheight adjuster button.Release the button to lock the anchor intoposition. Try sliding the height adjuster to makesure that it has locked into the position.
WARNING:
o The height adjuster must be in the locked
position when the vehicle is moving.
o The misadjustment of height of the shoul- der belt could reduce the effectivenessof the seat belt in a crash.
YR10301B
B180A03Y-GAT
SEAT BELTS-Driver's an d passenger's
3-Point System with Webbing Clamp
Locking Retractor ( If Installed)
To Fasten Your Belt To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle.There will be an audible "click" when the tablocks into the buckle.The seat belt automatically adjusts to the properlength only after the lap belt is adjusted manu-ally so that it fits snugly around your hips. If youlean forward in a slow, easy motion, the belt willextend and let you move around. If there is a sudden stop or impact, however, the belt willlock into position. It will also lock if you try tolean forward too quickly. Check to make surethat the belt is properly locked and that the beltis not twisted.

FEATURES OF YOUR HYUNDAI
1- 16
SSA1090R
B210A01A-AAT To Release the Seat Belt The seat belt is released by pressing the re- lease button in the locking buckle. When it isreleased, the belt should automatically drawback into the retractor.If this does not happen, check the belt to besure it is not twisted, then try again.
SSA1090S
B220A01A-AAT SEAT BELTS (2-Point Static Type) (Rear Seat Center) (If Installed)To Fasten Your Seat Belt To fasten a 2-point static type belt, insert the metal tab into the locking buckle. There will bean audible "click" when the tab locks into thebuckle. Check to make sure the belt is properlylocked and that the belt is not twisted.
STA1090Q
B200A01S-GAT Adjusting Your Seat Belt You should place the belt as low as possible on your hips, not on your waist. If the belt is locatedtoo high on your body, you could slide under itin case of accident or a sudden stop. This couldresult of death, serious injury or property dam-age. Both arms should not be under or over thebelt. Rather, one should be over and the otherunder, as shown in the illustration.Never wear the seat belt under the arm nearestthe door.
lock into position. It will also lock if you try tolean forward too quickly. Check to make surethat the belt is properly locked and that the beltis not twisted.

FEATURES OF YOUR HYUNDAI 1- 17
B220C01A-AAT To Release the Seat Belt
B220C01FC
When you want to release the seat belt, press the button in the locking buckle. WARNING: The center lap belt latching mechanism isdifferent from those for the rear seat shoul-der belts. When fastening the rear seat shoul-der belts or the center lap belt, make surethey are inserted into the correct buckles toobtain maximum protection from the seatbelt system and assure proper operation.
B220B01A-AAT Adjusting Your Seat Belt
SSA1090T
With a 2-point static type seat belt, the length must be adjusted manually so it fits snuglyaround your body. Fasten the belt and pull onthe loose end to tighten. The belt should beplaced as low as possible on your hips, not onyour waist. If the belt is too high, it couldincrease the possibility of your being injured inan accident. Correct
Shorten Too high B220A01FC-GAT
SEAT BELTS - Center Rear Seat 3-Point System With Emergency Locking Re-tractor (If installed)
1. Before fastening the rear seat center belt, confirm the metal tab (a) and buckle (b) are latched together.
2. After confirming that (a) and (b) are latched, pull the seat belt out of the retractor andinsert the metal tab (c) into the buckle (d).
There will be an audible "click" when the tablocks in the buckle. The seat belt automaticallyadjusts to the proper length only after the lap beltis adjusted manually so that it fits snugly aroundyour hips. If you lean forward in a slow, easymotion, the belt will extend and let you movearound. If there is a sudden stop or impact, thebelt will lock into position. It will also lock if youtry to lean forward too quickly.
B220A01FC
(a)
(b) (c)
(d)

FEATURES OF YOUR HYUNDAI
1- 18
WARNING:
o When using the rear seat center belt, you must lock all metal tabs and buck-les. If any metal tab or buckle is not locked, it will increase the chance of injury in the event of collision.
o Never unlock the metal tab (a) and the buckle (b) with the following excep-tions.
(1) In case of folding rear seatbacksdown.
(2) If transporting an object on the rear seat may cause damage to the rearseat center belt.
o Lock the metal tab (a) and the buckle (b) immediately after folding rear seatbacksup.
o To disconnect the metal tab (a) from the buckle (b), insert other metal tab intothe groove located on the buckle (b). B230A04P-GAT CHILD RESTRAINT SYSTEM (If Installed) Children riding in the car should sit in the rear seat and must always be properly restrained tominimize the risk of injury in an accident, sud-den stop or sudden maneuver. According toaccident statistics, children are safer whenproperly restrained in the rear seats than in thefront seat. Larger children not in a child restraintshould use one of the seat belts provided.You are required by law to use safety restraintsfor children. If small children ride in your vehicleyou must put them in a child restraint system(safety seat).Children could be injured or killed in a crash iftheir restraints are not properly secured. Forsmall children and babies, a child seat or infantseat must be used. Before buying a particularchild restraint system, make sure it fits your carand seat belts, and fits your child. Follow all theinstructions provided by the manufacturer wheninstalling the child restraint system. WARNING:
o A child restraint system must be placed
in the rear seat. Never install a child orinfant seat on the front passenger's seat.Should an accident occur and cause thepassenger side airbag to deploy, it couldseverely injure or kill an infant or childseated in an infant or child seat. Thus,only use a child restraint in the rear seatof your vehicle.
B220C01Y-GAY To Release the Seat Belt
When you want to release the seat belt, press
the button in the locking buckle. WARNING: The center belt latching mechanism is
different from those for the rear seat shoul- der belts. When fastening the rear seatshoulder belts or the rear seat center belt,make sure they are inserted into the cor-rect buckles to obtain maximum protec-tion from the seat belt system and assureproper operation.
B220A02Y-D
B220C02FC

FEATURES OF YOUR HYUNDAI
1- 20
YR10400B
On outboard rear
seats
B230G01A-GAT Installation on the Outboard Rear Seats To install a child restraint system on the outboard rear seats, extend the shoulder/lapbelt from its retractor. Buckle the seat belt andallow the seat belt to take up any slack. Makesure that the lap portion of the belt is tightaround the child restraint system and theshoulder portion of the belt is positioned sothat it cannot interfere with the child's head orneck. After installation of the child restraintsystem, try to move it in all directions to besure the child restraint system is securelyinstalled. If you need to tighten the belt, pull more webbing toward the retractor. When you un-buckle the seat belt and allow it to retract, theretractor will automatically revert back to itsnormal seated passenger emergency lockingusage condition. NOTE:
o Before installing the child restraint sys- tem, read the instructions supplied bythe child restraint system manufacturer.
o If the seat belt does not operate as described, have the system checkedimmediately by your authorized Hyundaidealer.
WARNING: Do not install any child restraint system in
the front passenger seat. Should an acci- dent occur and cause the passenger'sside airbag to deploy, it could severelyinjure or kill an infant or child seated in aninfant or child seat. Therefore, only use achild restraint system in the rear seat ofyour vehicle. B230B02A-GAT
Using a Child Restraint System with "Tether Anchorage"System For small children and babies, the use of a child seat or infant seat is strongly recom-mended. This child seat or infant seat shouldbe of appropriate size for the child and shouldbe installed in accordance with themanufacturer's instructions. It is further rec-ommended that the seat be placed in thevehicle's rear seat since this can make animportant contribution to safety. Your vehicleis provided three child restraint hook holdersfor installing the child seat or infant seat.
Cover, Child Restraint Hook Holder (4 door only)
Bolt, Holder (5/16"-30 mm)
Washer, Conical Spring Holder, Child Restraint Hook
Spacer (10 mm), Child Restraint Hook Holder Retainer Washer
B230B01FC