2004 Hyundai Getz keyless entry

FEATURES OF YOUR HYUNDAI 1- 9
HTB052 Park the car and stop the engine. Arm the system as described below.
1) Remove the ignition key from the
ignition switch.
2) Make sure that the engine hood and tail gate are locked.
3) Lock the doors using the transmitter
of the keyless entry system.
After completion of the steps above, the turn signal lights will blink once toindicate that the system is armed. NOTE:
1) If any door, tail gate or engine hood remains open, the system will not be armed.
2) If this happens, rearm the system
as described above.
The central door locking is operated bypushing the driver's door lock switch toward the front or rear of the vehicle.If the passenger and rear doors are open when the switch is pushed, the door will remain locked when closed. NOTE:
o When pushing the switch toward
the rear, all doors and tail gate will unlock. When pushing the switch toward the front, all doors and tail gatewill lock.
o When the door is unlocked, the
red mark on the switch is visibleand the character "LOCK" on the switch is visible.
o The central door locking is oper- ated by turning the key (with theft-alarm system: driver's door and passenger's door, without theft-alarm system: driver's door only) toward the front or rear of the vehicle. B070A01A-AAT THEFT-ALARM SYSTEM (If Installed) This system is designed to provide protection from unauthorized entry into the car. This system is operated inthree stages: the first is the "Armed" stage, the second is the "Alarm" stage, and the third is the "Disarmed" stage.If triggered, the system provides an audible alarm with blinking of the turn signal lights. B070B01O-GAT Armed Stage
CAUTION:
Do not arm the system until all passengers have left the car. If the system is armed while apassenger(s) remains in the car, the alarm may be activated when the remaining passenger(s) leavesthe car.
!

FEATURES OF YOUR HYUNDAI 1- 11
HTB053
B070F01TB-GAT Keyless Entry System (If Installed)Locking doors
1. Close all doors.
2. Push the button on the transmitter.
3. At the same time all doors lock, the
turn signal lights will blink once to indicate that the system is armed.
Unlocking doors
1. Push the button on the transmitter.
2. At the same time all doors unlock, the turn signal light will blink twice to indicate that the system is disarmed. B070E01TB-GAT Replacing the battery When the transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock thedoors, and the LED will not light. Re- place the battery as soon as possible. Battery type : CR1220 Replacement instructions:
1. Remove the screw with a (+) screw-
driver.
2. Separate the case with a (-) screw- driver as shown in the illustration. 3. Remove four screws back side of
the built-in circuit. HTB054
HTB055
Battery
4. Remove the old battery from the case and note the polarity. Make sure the polarity of the new battery is the same (+side facing up), then insert it in the transmitter.

FEATURES OF YOUR HYUNDAI 1- 7
B070A01A-EAT
ANTI-THEFT ALARM SYSTEM
(Not all models)
This system is designed to provide
protection from unauthorized entry into
the car. This system is operated in
three stages: the first is the "Armed"
stage, the second is the "Alarm" stage,
and the third is the "Disarmed" stage. If
triggered, the system provides an au-
dible alarm with blinking of the turn
signal lights.
The central door locking is operated by
pushing the driver's door lock switch
toward the front or rear of the vehicle. If
the passenger and rear doors are open
when the switch is pushed, the door will
remain locked when closed.
NOTE:
o When pushing the switch toward
the rear, all doors and tail gate will
unlock.
When pushing the switch toward
the front, all doors and tail gate
will lock.
o When the door is unlocked, the
red mark on the switch is visible
and the character "LOCK" on the
switch is visible.
o The central door locking is oper- ated by turning the key (with theft-
alarm system: driver's door and
passenger's door, without theft-
alarm system: driver's door only)
toward the front or rear of the
vehicle. Park the car and stop the engine. Arm
the system as described below.
1) Remove the ignition key from the
ignition switch.
2) Make sure that the engine bonnet and hatchback door are closed.
3) Lock the doors using the transmitter
of the keyless entry system.
After completion of the steps above,
the turn signal lights will blink once to
indicate that the system is armed.
NOTE:
1) If any door, hatchback door or engine bonnet remains open, the
system will not be armed.
2) If this happens, rearm the system
as described above.
CAUTION:
Do not arm the system until all pas-
sengers have left the car. If the sys-
tem is armed while a passenger(s)
remains in the car, the alarm may be
activated when the remaining
passenger(s) leaves the car.
!
HTB052-D
B070B01O-EAT
Armed Stage
tbuk-1a.p65
3/23/04, 2:21 PM
7

FEATURES OF YOUR HYUNDAI 1- 9
HTB053
B070F01TB-EAT
Keyless Entry System
(Not all models)
Locking doors
1. Close all doors.
2. Push the button on the transmitter.
3. At the same time all doors lock, the
turn signal light will blink once to
indicate that the system is armed.
Unlocking doors
1. Push the button on the transmitter.
2. At the same time all doors unlock, the turn signal light will blink twice to
indicate that the system is disarmed. B070E01TB-GAT
Replacing the battery
When the transmitter's battery begins
to get weak, it may take several pushes
on the button to lock or unlock the
doors, and the LED will not light. Re-
place the battery as soon as possible.
Battery type : CR1220
Replacement instructions:
1. Remove the screw with a (+) screw-
driver.
2. Separate the case with a (-) screw- driver as shown in the illustration. 3. Remove four screws back side of the
built-in circuit. HTB054
HTB055
Battery
4. Remove the old battery from the case and note the polarity. Make
sure the polarity of the new battery
is the same (+side facing up), then
insert it in the transmitter.
tbuk-1a.p65 3/23/04, 2:21 PM
9