2004 Hyundai Getz ECO mode

1- 112 FEATURES OF YOUR HYUNDAI
H290F01O-GAT
1. AUDIO/MP3 CD Select Button
o Insert the CD with the label facing
upward.
o Insert the CD to start CD playback, during radio operation or cassette tape playing.
o When a disc is in the CD deck, if you press the CD button the CD playerwill begin playing even if the radio orcassette player is being used.
o The CD player can be used when the
ignition switch is in either the "ON" or"ACC" position.
o Push the CD ˜MP3 button to turn on
that function without pushing PowerON-OFF control knob.
NOTE:
o Do not stick paper or tape etc., auto the label side or the record- ing side of any discs, as it may cause a malfunction.
o The unit cannot play a CD- R(Recordable CD) and CD-RW(Rewritable CD) that is not fi- nalized. Please refer to the manualof CD-R/CD-RW recoder or CD-R/ CD-RW software for more informa- tion on finalization process. o Depending on the recording sta-
tus, some CD-Rs/CD-RWs may notbe played on this unit.
2. FF/REW ( / ) If you want to fast forward or reverse through the compact disc track, push and hold the FF ( ) or REW ( ) button.When you release the button, the com- pact disc player will resume playing.
3. TRACK UP/DOWN
o The desired track on the disc cur- rently being played can be selected using the track number.
o Press button once to skip for- ward to the beginning of the nexttrack. Press button once to skipback to the beginning of the track.
4. REPEAT (RPT)
o To repeat the track you are currently listening to, press the RPT button. To cancel, press it again.
o To repeat the music within selected folder, press the RPT button for morethan 2 seconds. To cancel, press itagain. (MP3 CD only) o If you do not release RPT operation
when the track ends, it will automati-cally be replayed.This process will be continued until you push the button again.
5. RANDOM (RDM)
o Press the RDM button to listen the tracks in random, rather than se- quential, order. Press it again to cancel random play.
o To listen the music within the se-
lected folder in random order, pressthe RDM button for more than 2 seconds. To cancel press it again.(MP3 CD only)
6. EQUALIZER (EQ) Press the EQ button to select the CLAS- SIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display asfollows;
CLASSIC JAZZ ROCK DEFEAT

1- 116 FEATURES OF YOUR HYUNDAI
B290H01TB-GAT
1. CD CHANGER Select Button
(CD ˆ
MP3)
When the CD changer magazine con- tains discs, press the "CD ˆ
MP3" button
and the CD changer can be used even if the radio or cassette player is being used. The Hyundai CD changer can hold up to six or eight discs. The discnumber will be lit, and the track number, and elapsed time will be displayed. 2. DISC Select Knob
(JOY STICK)
To select the CD you want push the DISC select knob (JOY STICK) to up and down. After selecting the desiredCD, push the change the disc number. 3. FF/REW ( / ) If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( )button. When you release the button, the com- pact disc player will resume playing.4. TRACK UP/DOWN
o The desired track on the disc cur- rently being played can be selected using the track number.
o Press once to skip forward to the
beginning of the next track. Press
once to skip back to the beginning of the track.
5. JOYSTICK You can skip the track by pushing the JOY STICK to the left or right. After selecting the desired track, pressthe JOY STICK to playback the track. If you do not press the JOY STICK within 5 seconds, the previous track willplayback again. 6. REPEAT
o To repeat the track you are listening to, press the RPT button. To cancel, press again.
o If you do not release RPT operation
when the track ends, it will automati-cally be replayed. This process will be continued until you push the button again.7. RANDOM (RDM) Press the RDM button to listen the tracks in random, rather than sequen-tial, order. Press it again to cancel random play.
8. SCAN
o Press the SCAN button to playbackthe first 10 seconds of each track.
o Press the SCAN button again within
10 sec. for the desired track.
9. EQUALIZER (EQ)Press the EQ button to select the CLAS- SIC, JAZZ, ROCK and DEFEAT MODEfor the desired tone quality. Each press of the button changes the display as follows;
CLASSIC JAZZ ROCK DEFEAT

2- 14 DRIVING YOUR HYUNDAI
o Drive at a moderate speed. The
faster you drive, the more fuel your car uses. Driving at a moderatespeed, especially on the highway, is one of the most effective ways to reduce fuel consumption.
o Don't "ride" the brake or clutch pedal. This can increase fuel consumptionand also increase wear on thesecomponents. In addition, driving with your foot resting on the brake pedal may cause the brakes to overheat,which reduces their effectiveness and may lead to more serious con- sequences.
o Take care of your tires. Keep them inflated to the recommended pres-sure. Incorrect inflation, either toomuch or too little, results in unnec- essary tire wear. Check the tire pres- sures at least once a month.
o Be sure that the wheels are aligned correctly. Improper alignment canresult from hitting curbs or drivingtoo fast over irregular surfaces. Poor alignment causes faster tire wear and may also result in other prob-lems as well as greater fuel con- sumption.
WARNING:
ABS will not prevent accidents due to improper or dangerous driving maneuvers. Even though vehicle control is improved during emer-gency braking, always maintain a safe distance between you and ob- jects ahead. Vehicle speeds shouldalways be reduced during extreme road conditions. The braking distance for cars equipped with an anti-lock braking system may be longer than for those without it in the following road con-ditions.
o Driving on rough, gravel or snow- covered roads.
o Driving with tire chains installed.
o Driving on roads where the road
surface is pitted or has different surface height.
!During these conditions, the ve- hicle should be driven at reduced speeds. The safety features of anABS equipped vehicle should not be tested by high speed driving or cornering. This could endanger thesafety of yourself or others.
C140A01A-GAT DRIVING FOR ECONOMY You can save fuel and get more kilo- meters from your car if you follow these suggestions:
o Drive smoothly. Accelerate at amoderate rate. Don't make "jack- rabbit" starts or full-throttle shifts and maintain a steady cruisingspeed. Don't race between stop- lights. Try to adjust your speed to that of the other traffic so you don'thave to change speeds unneces- sarily. Avoid heavy traffic whenever possible.Always maintain a safe distance from other vehicles so you can avoid unnecessary braking. This also re-duces brake wear.

FEATURES OF YOUR HYUNDAI 1- 3
B020A01FC-EAT
RUNNING IN YOUR NEW
HYUNDAI (Petrol Engine)
The longevity and performance of the
vehicle are greatly affected by the care
exercised during the first 1,000 miles of
motoring. Because of modern manu-
facturing techniques, rigid guidelines
regarding maximum road speeds have
become unnecessary. However, cer-
tain precautions should be observed in
order to obtain the best possible perfor-
mance and useful life from the vehicle.
1) Do not race the engine without a load
(i.e revving the engine in neutral).
2) During the first 500 miles the maxi-
mum engine speed should be re-
stricted to 3,000 rpm and gradually
increased thereafter.
3) Avoid prolonged constant speed op- eration. The internal components of
the engine will become more quickly
run in if the operation speed is varied
during the running-in period.
4) Never allow the engine to labour. Use
the gearbox freely and avoid large
throttle openings when the engine
speed is below 1,500 rpm.
5) Avoid rapid acceleration and maxi- mum throttle openings.
6) Avoid harsh braking during the first
100 miles of urban motoring or 1,000
miles of motorway driving to allow
the friction facings of the brake pads
and shoes to bed against the discs
and drums properly.
7) No trailer towing should be under-
taken during the running-in period.
B020B01FC-EAT
(Diesel Engine)
The longevity and performance of the
vehicle are greatly affected by the care
exercised during the first 1,000 miles of
motoring. Because of modern manu-
facturing techniques, rigid guidelines
regarding maximum road speeds have
become unnecessary. However, cer-
tain precautions should be observed in
order to obtain the best possible perfor-
mance and useful life from the vehicle. 1) Do not race the engine without a load
(i.e revving the engine in neutral).
2) During the first 600 miles the maxi- mum engine speed should be re-
stricted to 3,000 rpm and gradually
increased thereafter. And while driv-
ing, keep under three quarters of
maximum vehicle speed.
3) Avoid prolonged constant speed op- eration. The internal components of
the engine will become more quickly
run in if the operation speed is varied
during the running in period.
4) Never allow the engine to labour. Use
the gearbox freely and avoid large
throttle openings when the engine
speed is below 1,500 rpm.
5) Avoid rapid acceleration and maxi- mum throttle openings.
6) Avoid harsh braking during the first
100 miles of urban motoring or 1,000
miles of motorway driving to allow
the friction facings of the brake pads
and shoes to bed against the discs
and drums properly.
7) No trailer towing should be under
taken during the running in period.
tbuk-1a.p65 3/23/04, 2:21 PM
3

1- 6 FEATURES OF YOUR HYUNDAI
SB040G1-F
CENTRAL DOOR LOCK
(Not all models)
SB040D1-F
Locking from the Inside
To lock the doors from inside, simply
close the door and push the lock switch
to the "LOCK" position.
When this is done, the door cannot be
using either the inside or the outside
door handle. SB040F1-E
CHILD-PROOF REAR DOOR
LOCK
The rear doors are fitted with child proof
locks to prevent accidental opening of
the doors using the inside door handle,
whilst allowing access by means of the
outside handle (such as is required in
the event of an acccident for example)
provided that the door lock button is at
the unlocked position. Use of the child
o To help prevent theft, always re-
move the ignition key, close all
windows, and lock all doors and
tail gate when leaving your ve-
hicle unattended.
NOTE:
When the door is locked, the red
mark on the switch is not visible and
the character "LOCK" on the switch
is visible. proof lock mechanism is recommended
when children are carried in the vehicle.
The child proof lock mechanism may
be activated by opening the door and
moving the lever located by the door
latch to the " " position. Move the
lever to the opposite direction of " "
position when normal door operation is
desired.
HTB057-D
UNLOCK
LOCK
HTB058-D
HTB212-D
tbuk-1a.p65 3/23/04, 2:21 PM
6

FEATURES OF YOUR HYUNDAI 1- 7
B070A01A-EAT
ANTI-THEFT ALARM SYSTEM
(Not all models)
This system is designed to provide
protection from unauthorized entry into
the car. This system is operated in
three stages: the first is the "Armed"
stage, the second is the "Alarm" stage,
and the third is the "Disarmed" stage. If
triggered, the system provides an au-
dible alarm with blinking of the turn
signal lights.
The central door locking is operated by
pushing the driver's door lock switch
toward the front or rear of the vehicle. If
the passenger and rear doors are open
when the switch is pushed, the door will
remain locked when closed.
NOTE:
o When pushing the switch toward
the rear, all doors and tail gate will
unlock.
When pushing the switch toward
the front, all doors and tail gate
will lock.
o When the door is unlocked, the
red mark on the switch is visible
and the character "LOCK" on the
switch is visible.
o The central door locking is oper- ated by turning the key (with theft-
alarm system: driver's door and
passenger's door, without theft-
alarm system: driver's door only)
toward the front or rear of the
vehicle. Park the car and stop the engine. Arm
the system as described below.
1) Remove the ignition key from the
ignition switch.
2) Make sure that the engine bonnet and hatchback door are closed.
3) Lock the doors using the transmitter
of the keyless entry system.
After completion of the steps above,
the turn signal lights will blink once to
indicate that the system is armed.
NOTE:
1) If any door, hatchback door or engine bonnet remains open, the
system will not be armed.
2) If this happens, rearm the system
as described above.
CAUTION:
Do not arm the system until all pas-
sengers have left the car. If the sys-
tem is armed while a passenger(s)
remains in the car, the alarm may be
activated when the remaining
passenger(s) leaves the car.
!
HTB052-D
B070B01O-EAT
Armed Stage
tbuk-1a.p65
3/23/04, 2:21 PM
7

1- 10 FEATURES OF YOUR HYUNDAI
!
HTB257-D
SB060A1-E
DOOR WINDOWS
The front door windows may be opened
or closed by turning the window regula-
tor handle. Ensure that when the win-
dows are closed, nothing may become
trapped between the glass and the door
frame. HTB064-D
(1)
HTB066-D
In order to prevent operation of the
passenger front and rear windows, a
window lock switch is provided on the
armrest of the driver's door. To disable
the power windows, press the window
lock switch.
To revert to normal operation, press the
window lock switch a second time.
Auto-Down Window
(Driver's Side)
The Auto-Down window is moved to its
fully open position by pushing the
switch. To stop at the desired position
push the switch again.
B060A01E-EAT
POWER WINDOWS
(Not all models)
The power windows operate when the
ignition key is in the "ON" position. The
main switches are located on the driver's
armrest and control the front and rear
windows on both sides of the vehicle.
The windows may be opened by de-
pressing the appropriate window switch
and closed by pulling up the switch. To
open the window on the driver's side,
press the switch(1) down. The window
moves as long as the switch is oper-
ated.
WARNING:
When opening or closing the win-
dows, make sure your passenger's
arms and hands are safety out of the
way.
tbuk-1a.p65 3/23/04, 2:21 PM
10

FEATURES OF YOUR HYUNDAI 1- 13
HTB025-D
SB070F1-F
Seat Cushion Height Adjustment
(Not all models) (Driver's seat
only)
To raise or lower the front part of the
seat cushion, turn the front knob for-
ward or rearward.
To raise or lower the rear part of the seat
cushion, turn the rear knob forward or
rearward.HTB027-D
SB070E1-E
Lumbar Support Adjustment
(Not all models) (Driver's seat
only)
Some models are fitted with adjustable
driver seat lumbar support which may
be used to increase the amount of
lumbar support offered by the seat back.
Adjustment is performed by moving the
handle at the side of the backrest in a
forward direction to increase the sup-
port.
!WARNING:
o For maximum effectiveness in case of an accident, the headrest should
be adjusted so the top of the head-
rest is at the same height as the
top of the occupant's ears. The
use of a cushion that holds the
body away from the seatback is
not recommended.
o Do not operate the vehicle with the headrests removed as severe in-
jury to an occupant may occur in
the event of an accident. Head-
rests may provide protection
against severe neck injuries when
properly adjusted.
tbuk-1a.p65 3/23/04, 2:21 PM
13