2004 HONDA PILOT remote control

µ
The HomeLink
Universal
Transceiver built into your vehicle
canbeprogrammedtooperateupto
three remote controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor f or that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
The HomeLink Transceiver stores
the code in a permanent memory.
There should be no need to retrain
HomeLink if your vehicle’s battery
goes dead or is disconnected.
If your garage door opener was
manuf actured bef ore April 1982, you
may not be able to program
HomeLink to operate it. They do not
have the safety feature that causes the motor to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury.
Always ref er to the opening
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with the HomeLink
Universal Transceiver. If you do not
have this information, contact the
manuf acturer of the equipment.
If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the f irst button. To do this,
press and hold the two outside
buttons on HomeLink Transceiver
f or about 20 seconds, or until the red
light f lashes. Release the buttons,
then proceed to Step 1. If you are training the second or
third buttons, go directly to Step 1.
Unplug the garage door opener
motor f rom the house current.
Holdtheendof thegaragedoor
opener remote control 2 to 5
inches f rom HomeLink. Make
sure you are not blocking your
view of the red light in HomeLink.
2. 1.
On EX Models
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures
General Inf ormation Important Saf ety Precautions
T raining HomeL ink
Bef ore you begin
118

Press and hold the remote control
button and one of the HomeLink
buttons at the same time.The remote
control you are training f rom may
stop transmitting after two
seconds. This is not long enough
f or HomeLink to learn the code.
Release and press the button on
the remote control every two
seconds until HomeLink has
learned the code.
The red light in HomeLink should
begin f lashing. It will f lash slowly
at first, then rapidly.
When the red light f lashes rapidly,
release both buttons. HomeLink
should have learned the code from
the remote control. Plug in the garage door opener
motor, then test the HomeLink
Transceiver button by pushing it.
If the button does not work, repeat
the procedure to train it again. If it
still does not work, you may have a
variable or rolling code garage
door opener. See if you do by
pressing and holding the
HomeLink transceiver button you
just trained. If the red light blinks
f or two seconds, then stays on,
you have a rolling code garage
door opener. Go to ‘‘Training With
a Rolling Code System’’ (see page
).
Repeat these steps to train the
other two HomeLink buttons to
operate any other remotely-
controlled devices around your
home (lighting, automatic gate,
security system, etc.).
3.
4.
5.
6.
7.
120
Canadian Owners:
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures119

µµ
For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Inf ormation f rom
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so they send and
receive the correct codes.
Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure.
Find the ‘‘Training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer. Press the Training button on the
garage door opener unit until the
light next to the button comes on,
then release it. The light may blink,
or come on and stay on. You then
have approximately 30 seconds to
complete the f ollowing steps.
Press and hold the button on
HomeLink f or 3 4 seconds.
Press and hold the HomeLink
button again f or 3 4 seconds.This should turn of f the training
light on the garage door opener
unit. (Some systems may require
youtopressthebuttonuptothree
times.)
Press the HomeLink button again.
It should operate the garage door.
Toerasethecodesstoredinallthree
buttons, press and hold the two
outside buttons until the red light
begins to f lash, then release the
buttons.
Youshoulderaseallthreecodes
bef ore selling the vehicle.
Totrainanalreadyprogrammed
transceiver button with a new device,
you do not have to erase all the
memory. Train the selected button
over the existing memory code
following the steps under .
6.
2. 4.
5.
1.
3.
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures
T raining With a Rolling Code
System
Erasing Codes
Retraining a ButtonT raining
HomeL ink
120
TRAINING BUTTON

...
Octane Requirement, Gasoline . 124
.........................................
Odometer .54
...............................
Odometer, Trip .54
....................
Of f -Highway Driving . 155
...................
Of f -Road Precautions . 155
Oil ........................
Change, How to .172
..............
Change, When to . 164,165
......................
Checking Engine .127
..............
Pressure Indicator . 48,206
Selecting Proper Viscosity ......................................
Chart .171
...........
ON (Ignition Key Position) . 64
Onboard Ref ueling Vapor ................................
Recovery .223
..............................
Outside Mirrors .74
....................
Overheating, Engine .204
....
Owner’s Maintenance Checks . 163 ...................
Radiator Overheating . 204
Radio/CD Sound ..........................................
System .88
..........................
Readiness Codes .226
.................................
Rear A/C Unit .87
............
Rear Audio Control Panel . 107
........
Rear Entertainment System . 104
..
Rear Lights, Bulb Replacement . 182
............................
Rear View Mirror .74
.................
Rear Window Def ogger . 60
.
Rear Window Wiper and Washer . 57
.........
Reclining the Seat Backs . 68,69
...........
Reclining the Second Seats . 70
................
Reclining the Third Seat . 71
.............................
Reminder Lights .47
................
Remote Audio Controls . 101
.................
Remote Control (RES) . 109
.......................
Remote Transmitter .66
Replacement Inf ormation ..............
Dust and Pollen Filter . 185
................
Engine Oil and Filter . 172
.................................
Floor Mats .185
..........................................
Fuses .210
................................
Light Bulbs .180
..............
Panel Brightness Control . 59
........................
Park Gear Position .139 ...........................................
Parking .143
.................................
Parking Brake .75
Parking Brake and Brake System ...............................
Indicator .49, 208
.................................
Parking Lights .58
..
Parking Over Things that Burn . 225
............................
Playing the Radio .88
....................................
Playing a CD .93
....................
Playing a CD Changer . 94
.................................
Playing a Tape .98
.............................
PGM-FI System .224
..........................
Power Door Locks .65
................
Power Seat Adjustments . 68
.................
Power Socket Locations . 76
..............................
Power Windows .73
.........
Pregnancy, Using Seat Belts . 15
.........
Protecting Adults and Teens . 10
...
Additional Safety Precautions . 16
.....
Advice f or Pregnant Women . 15
........................
Protecting Children .25
.....................
General Guidelines .25
...........................
Protecting Inf ants .29
...........
Protecting Larger Children . 38
.............
Protecting Small Children . 30
Index
O
P R
VI