2004 HONDA ACCORD COUPE clock

If your vehicle’s battery is
disconnected or goes dead, you will
need to set the clock.
To set the time, press the Clock Set
button (SOUND) until you hear a
beep. The displayed time begins to
blink.
Press and hold the H (Preset 4) side
of the bar until the hour advances to
the desired time. Press and hold the
M (Preset 5) side of the bar until the
minutes advance to the desired time.
Press the Clock Set button
(SOUND) again to enter the set time.The upper display shows the time
when the ignition switch is in the
ACCESSORY (I) or ON (II) position.
The Navigation System receives
signals f rom the Global Positioning
System (GPS), and the displayed
time is updated automatically by the
GPS. Ref er to the Navigation System
Owner’s Manual to set up the time.
You can quickly set the time to the
nearest hour. If the displayed time is
bef ore the half hour, pressing the
Clock Set (SOUND) button until you
hear a beep, then pressing the R
(Preset 6) side of the bar sets the clockbacktotheprevioushour.If
the displayed time is after the half
hour, the clock sets f orward to the
beginning of the next hour.
For example:
1:06 will reset to 1:00
1:53 will reset to 2:00
Setting the Clock
Comf ort and Convenience Feat ures
On Vehicles wit hout Navigat ion
Syst em
On Vehicles wit h Navigat ion Syst em
154
CLOCK SET BUTTONDIGITAL CLOCK
PRESET BARS
EX-L and EX-V6
without navigation system
——y

y
(%
y
y

When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Pour the coolant slowly and caref ully
so you do not spill. Clean up any
spills immediately; it could damage
components in the engine
compartment.
Put the radiator cap back on, and
tighten it fully.
4. 5.
1. 2. 3.
Engine Coolant
Maint enance222
RESERVE TANK
4-cylinder models 6-cylinder models 4-cylinder models
RADIATOR CAP
RADIATOR CAP
——y

y
(%
yy

Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Install the new bulb and turn it
one-quarter turn clockwise to lock
it in place.Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
3.
2. 4. 5.
Lights
Maint enance234
6-cylinder modelsAIR INTAKE
COVER
FASTENERS
4-cylinder models 6-cylinder modelsTAB BULB
TABBULB
——y


y
(%
yy

To change the low beam headlight
bulb on the driver’s side, remove
the air intake duct. You can reach
the air intake duct f rom the back
side of the inner f ender.Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.Install the new bulb and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the air intake duct
securely.
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter.
6.
5. 7. 8.9.
10. 11.
4.
On EX-V6 model with manual
transmission
On EX-V6 model with manual transmission
Lights
Maint enance236
AIR INTAKE DUCT
EX-V6 with M/T
——y
y
(%
yy

To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
1.
3.
2.
4.
CONT INUED
Lights
Maint enance
Replacing a Front T urn Signal/
Parking/Side Marker Light Bulb
237
HOLDING CLIPS
——y
y
(%
yy

Remove the burned out bulb f rom
thesocketbypushingitinand
turning the bulb counterclockwise
until it unlocks.
Install the new bulb in the socket.
Turn it clockwise to lock it in place.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter.Open the trunk.
Remove the light assembly cover
by pulling its outside edge.Determine which of the three
bulbs is burned out: stop/taillight/
side marker, back-up or turn
signal.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Turn on the lights to make sure
the new bulb is working.
Install the light assembly cover.
Make sure it snaps into place.
1. 3.
2. 4. 5.6. 7.
5. 6. 7. 8. 9.
Lights
Maint enance
Replacing Rear Bulbs
238
COVER
——y
y
(%
y
y

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb into the
socket.Reinstall the socket. Turn it
clockwise until it locks.
Turn on the lights to make sure
the new bulb is working.
1. 2. 3. 4.
Lights
Maint enance
Replacing a High-mount Brake
Light Bulb
239
BULB
SOCKET
——y
y
(%
yy

The jack is behind a cover in the
right f ender. Remove the cover by
turning the handle counterclock-
wise, then pulling on the cover.Turn the jack’s end bracket
counterclockwise to loosen it, then
remove the jack.
Loosen each wheel nut 1/2 turn
with the wheel wrench.
6.
7.8.
Changing a Flat T ire
T aking Care of t he Unexpect ed258
JACK
WHEEL WRENCHWHEEL NUT
——y
y
(%
y
y