2004 GMC YUKON reset

7
Entertainment Systems —
Radio/CD
Set the time on radios withouta
Radio Data System (RDS)
•Press and hold the HR or MIN arrow
for two seconds.
•Press the HR (down) arrow until the
correct hour appears on the display.
•Press and hold the MIN (up) arrow
until the correct minute appears on
the display.
Set the time on radios witha Radio
Data System (RDS)
Your radio may have a button marked
“H” or “HR” to represent hours and an
“M” or “MIN” to represent minutes.
•Press and hold the hour button until
the correct hour appears on the
display.
•Press and hold the minute button
until the correct minute appears on
the display.Program radio station presets
•Turn the radio on.
•Press BAND to select the band (AM,
FM1/FM2/XM1/XM2).
•Use the seek or tune knob to tune in
the desired station.
•Press AUTO EQ or AUTO TONE (as
applicable to your radio) to select the
equalization that best suits the type of
station selected.
•Press and hold one of the six num-
bered buttons until a beep sounds;
release the button.
•Repeat these steps for each station
preset, using a different numbered
button for each station.
Access one of the two available XM
Satellite Radio bands (if equipped)
•Press the BAND button until XM1 or
XM2 appears on the display. (Note:
Requires subscription to XM Radio.)
Note:The time may be set with the
ignition on or off.

9
HomeLink®Transmitter
(if equipped)
Program HomeLink
1. Determine which of the three chan-
nels (buttons) you want to program:
garage door opener, gate opener,
entry door locks or other.
2. Press and hold the desired HomeLink
button through step 3.
3. When the HomeLink light blinks slow-
ly (within 30 seconds), hold your
transmitter/opener 1" to 3" away from
the HomeLink buttons. Then hold
your transmitter button on until the
HomeLink light flashes rapidly (up to
90 seconds). The process is now
complete.
See Section 2 of your Owner Manual.
Close the sunroof
•Hold the front portion of the button
(“B”) down until the sunroof motor
stops. The sunroof will tilt up slightly
to seal. This is normal.
Open sunroof to vent position
•Press and hold the front portion of
button (“B”) when the sunroof is
closed.
Note:If your transmitter has a “rolling
code” feature, the above process may
not work. Please refer to your Owner
Manual or contact HomeLink at
1-800-335-3515 (www.homelink.com).
Steering Wheel Controls
(OnStar®/ Radio) (if equipped)
(OnStar/Voice Recognition)
(if equipped): This button will activate
OnStar
®for use. (Note: If your vehicle is
not equipped with the OnStar®
Communications system, pressing this
button will mute the radio. For additional
OnStar
®features information, including
Personal Calling and Virtual Advisor, see
the OnStar
®System section of your
Owner Manual.)
PROG:This button will cycle through
the radio presets.
:Selects AM, FM, XM Satellite
Radio (if equipped), cassette or CD
:Seeks radio stations
:Adjusts radio volume
See Sections 2 and 3 of your Owner Manual.

Getting to Know YourYukon/Yukon Denali10
Automatic Headlamp Controls
Turn off Daytime Running Lamps
(DRL) and automatic headlamps
•Turn the exterior lamps knob (located
to the left of the steering wheel) to
OFF ( ).
Activate the
automatic
headlamp
system
•Turn the
exterior
lamps
knob to
AUTO. The automatic headlamp sys-
tem will turn on the front and rear
lamps.
Illuminate the parking lamps, side-
marker lamps, taillamps, instrument
panel/radio lights, license plate lamps
and roof marker lamps (if equipped)
•Turn the exterior lamps knob to the
parking lamp position ( ).
Power Camper-Type Mirrors
(if equipped)
Extend or retract mirrors
•Move the selector switch located
above the mirror control to the center
position (as shown under Power
Folding Mirrors above).
•Press the left side of the four-way
control pad to extend mirrors.
•Press the right side of the four-way
control pad to retract mirrors.
See Section 2 of your Owner Manual.
Power Folding Mirrors
(if equipped)
Fold mirrors
•Move the
selector switch
located above
the mirror
control (“A”
above) to
the center
position.
•Press the right
side of the
four-way control pad (“B” above)
to fold the mirrors in.
•Press the left side of the four-way
control pad to fold the mirrors out.
If the mirrors have been folded manual-
ly, they must be moved through the
power folding cycle three times to reset
them in their tracks.
See Section 2 of your Owner Manual.
Adjustable Pedals
(if equipped)
The buttons used to
adjust the pedals are
located on the driver’s
side door panel.
•Press the button
closest to you to
move the pedals closer to your body.
•Press the button farthest from you to
move the pedals away from your
body.
The vehicle must be in PARK (P) for this
feature to operate.
See Section 2 of your Owner Manual.
A
B

Arm the system
•Lock the doors using
the power door lock
switch or the Keyless
Entry System trans-
mitter. The alarm is
activated when the symbol shown
above illuminates in the instrument
panel cluster (approximately 30
seconds).
If your vehicle is equipped with a Driver
Information Center, you can program the
alarm to the following:
Manually activate the headlamps, all
exterior tail/marker lamps and the
instrument panel/radio lights
•Turn the exterior lamps knob to this
position ( ).
Turn the fog lamps (if equipped) on
or off
•Press the fog lamp
button located on
the left side of the
instrument panel.
An indicator lamp
will illuminate when
the fog lamps are on.
See Section 3 of your Owner Manual.11
Daytime Running Lamps (DRL)
Disable the DRL when idling
•Shift the vehicle into PARK, or
•Set the parking brake.
See Section 3 of your Owner Manual.
Content Theft-Deterrent System
(if equipped)
•Both Horn/Headlamps
•Horn only
•Lamps only
•Off
See Section 2 of your Owner Manual.
Note:Your vehicle’s factory default
setting is Horn and Lamps. See the
Personalizing Your Vehicle section of
this booklet for more information.
Tire Pressure Monitor
(if equipped)
This feature alerts you when a
substantial reduction in pressure occurs
in one of your vehicle’s tires. If this
occurs, a CHECK TIRE PRESSURE
message will appear in the instrument
panel cluster. This message will remain
on until you reset the system.
Reset the tire pressure monitor
•To reset the tire pressure message,
you must fill the tires with the correct
amount of air. The best time to check
your tire pressure is when the tires
are cold.
•Pressing the cluster stem button on
your instrument panel cluster or the
Select/Reset button ( ) on your
steering wheel (if equipped) will
temporarily eliminate the message.
However, at the next vehicle start-up,
the message will reappear. The tire
pressure must be corrected to
permanently eliminate the message.
See Section 5 of your Owner Manual.
Note:The Tire Pressure Monitor
can alert you about low tire pressure,
but it doesn’t replace normal tire
maintenance.
Note:Your DRLs will re-engage at the
next key cycle.

Getting to Know YourYukon/Yukon Denali12
Memory Positions for Driver’s
Seat, Mirrors, Pedals, Radio and
Climate Controls (if equipped)
Use the driver’s
door mounted con-
trols to:
•Adjust driver
seat, including
lumbar
adjustment
•Adjust gas and
brake pedals
•Adjust the outside rearview mirrors
•Set the radio presets and climate
control temperature (the temperature
setting will revert to the last tempera-
ture setting used)
•Press and hold Memory 1 or 2 until
two chimes sound (about four
seconds)
•To set up for another driver, repeat
the process with the other memory
button
These settings will be remembered after
they are programmed by pressing the
Memory 1 or 2
button on the
driver’s door
(shown above).
If you unlock the
vehicle with the
Remote Keyless
Entry (RKE)
transmitter, the
vehicle memory
settings will correspond to the number
on the RKE transmitter: 1 or 2.
See Section 2 of your Owner Manual.
Memory Settings for Your
Vehicle (Driver Information
Center) (if equipped)
Your vehicle may be programmed with
the features shown below. To cycle
through them, use the
Personalization/Menu button ( )
located on your steering wheel.
•Alarm Warning Type
•Automatic Locking/Unlocking
•Perimeter Lighting
•Delayed Locking
•Remote Lock/Unlock Feedback
•Seat Position Recall
•Headlamps On at Exit
•Easy Exit Driver Seat
•Display Units
•Display Language
•Curb View Assist (if equipped)
Selection Options
Use the Select button ( ) to choose
your desired setting. The last setting
remaining on the display will be
the selection of choice. Continue
cycling through the menu with the
Personalization/Menu button ( )
to set other preferences.
Alarm W
arning Type
1. Alarm Warning: Both (default)
2. Alarm Warning: Off
3. Alarm Warning: Horn
4. Alarm Warning: Lamps

Getting to Know YourYukon/Yukon Denali14
Odometer/Trip Settings
(if equipped)
Your vehicle’s personal trip and busi-
ness trip odometers operate only when
they are turned on. The controls are
located on the steering wheel.
Enable the system
•Press the Trip button ( ) until the
words “Personal Trip” appear. Then
press ( ) to denote Personal Trip
ON. Press the Trip button again to
monitor your mileage. (Note:
Continue to press the Trip button to
monitor the features shown in the
next column.)Use the above procedure to monitor the
following settings:
•Personal/Business: Miles
•Personal/Business: Gal.
•Personal/Business: Avg. MPG
•Personal/Business: MPH
•Personal/Business: Annual % Usage
•Business: Hourmeter (Total Engine
Run Time)
•Business: Annual Log
•Business: Timer
Reset trip information
•Press and hold the Select button
( ) for two seconds while viewing
any of the trip modes on the Driver
Information Center.
See Section 2 of your Owner Manual.
Note:Whether your vehicle is equipped
with a Driver Information Center or not,
you can select and reset trip features by
using the Trip Odometer Reset Stem
located on the instrument panel cluster.