2004 GMC YUKON buttons

A. Air Outlets
B. Exterior Lamps Control
C. Turn Signal/Multifunction Lever
D. OnStar
®and Radio Steering
Wheel Control Buttons
E. Instrument Panel Cluster
F.Shift Lever/Tow/Haul Selector
Button
G. Audio System
H. Dome Lamp Override ButtonI. Rear Wiper Washer
J. Fog Lamps Button (if equipped)
K. Driver Information Center (DIC)
Buttons
L. Parking Brake Release
M. Tilt Wheel Lever
N. Comfort Control System
O. Storage Area (Denali models)P.Compact Disc Changer (Denali
models. Storage area (if equipped)
on Yukon models)
Q. Accessory Power Outlet
R. StabiliTrak
®Button (Denali location
shown. See “T” for Yukon models)
S. Glove Box
T.Automatic Transfer Case/
StabiliTrak®Mode Button (AWD
Vehicles)/Traction Assist System
(TAS) (Storage compartment on
Denali models)
Getting to Know YourYukon/Yukon Denali2
Instrument Panel
See Section 3 of your Owner Manual.(Denali Instrument Panel shown)

7
Entertainment Systems —
Radio/CD
Set the time on radios withouta
Radio Data System (RDS)
•Press and hold the HR or MIN arrow
for two seconds.
•Press the HR (down) arrow until the
correct hour appears on the display.
•Press and hold the MIN (up) arrow
until the correct minute appears on
the display.
Set the time on radios witha Radio
Data System (RDS)
Your radio may have a button marked
“H” or “HR” to represent hours and an
“M” or “MIN” to represent minutes.
•Press and hold the hour button until
the correct hour appears on the
display.
•Press and hold the minute button
until the correct minute appears on
the display.Program radio station presets
•Turn the radio on.
•Press BAND to select the band (AM,
FM1/FM2/XM1/XM2).
•Use the seek or tune knob to tune in
the desired station.
•Press AUTO EQ or AUTO TONE (as
applicable to your radio) to select the
equalization that best suits the type of
station selected.
•Press and hold one of the six num-
bered buttons until a beep sounds;
release the button.
•Repeat these steps for each station
preset, using a different numbered
button for each station.
Access one of the two available XM
Satellite Radio bands (if equipped)
•Press the BAND button until XM1 or
XM2 appears on the display. (Note:
Requires subscription to XM Radio.)
Note:The time may be set with the
ignition on or off.

9
HomeLink®Transmitter
(if equipped)
Program HomeLink
1. Determine which of the three chan-
nels (buttons) you want to program:
garage door opener, gate opener,
entry door locks or other.
2. Press and hold the desired HomeLink
button through step 3.
3. When the HomeLink light blinks slow-
ly (within 30 seconds), hold your
transmitter/opener 1" to 3" away from
the HomeLink buttons. Then hold
your transmitter button on until the
HomeLink light flashes rapidly (up to
90 seconds). The process is now
complete.
See Section 2 of your Owner Manual.
Close the sunroof
•Hold the front portion of the button
(“B”) down until the sunroof motor
stops. The sunroof will tilt up slightly
to seal. This is normal.
Open sunroof to vent position
•Press and hold the front portion of
button (“B”) when the sunroof is
closed.
Note:If your transmitter has a “rolling
code” feature, the above process may
not work. Please refer to your Owner
Manual or contact HomeLink at
1-800-335-3515 (www.homelink.com).
Steering Wheel Controls
(OnStar®/ Radio) (if equipped)
(OnStar/Voice Recognition)
(if equipped): This button will activate
OnStar
®for use. (Note: If your vehicle is
not equipped with the OnStar®
Communications system, pressing this
button will mute the radio. For additional
OnStar
®features information, including
Personal Calling and Virtual Advisor, see
the OnStar
®System section of your
Owner Manual.)
PROG:This button will cycle through
the radio presets.
:Selects AM, FM, XM Satellite
Radio (if equipped), cassette or CD
:Seeks radio stations
:Adjusts radio volume
See Sections 2 and 3 of your Owner Manual.

Getting to Know YourYukon/Yukon Denali10
Automatic Headlamp Controls
Turn off Daytime Running Lamps
(DRL) and automatic headlamps
•Turn the exterior lamps knob (located
to the left of the steering wheel) to
OFF ( ).
Activate the
automatic
headlamp
system
•Turn the
exterior
lamps
knob to
AUTO. The automatic headlamp sys-
tem will turn on the front and rear
lamps.
Illuminate the parking lamps, side-
marker lamps, taillamps, instrument
panel/radio lights, license plate lamps
and roof marker lamps (if equipped)
•Turn the exterior lamps knob to the
parking lamp position ( ).
Power Camper-Type Mirrors
(if equipped)
Extend or retract mirrors
•Move the selector switch located
above the mirror control to the center
position (as shown under Power
Folding Mirrors above).
•Press the left side of the four-way
control pad to extend mirrors.
•Press the right side of the four-way
control pad to retract mirrors.
See Section 2 of your Owner Manual.
Power Folding Mirrors
(if equipped)
Fold mirrors
•Move the
selector switch
located above
the mirror
control (“A”
above) to
the center
position.
•Press the right
side of the
four-way control pad (“B” above)
to fold the mirrors in.
•Press the left side of the four-way
control pad to fold the mirrors out.
If the mirrors have been folded manual-
ly, they must be moved through the
power folding cycle three times to reset
them in their tracks.
See Section 2 of your Owner Manual.
Adjustable Pedals
(if equipped)
The buttons used to
adjust the pedals are
located on the driver’s
side door panel.
•Press the button
closest to you to
move the pedals closer to your body.
•Press the button farthest from you to
move the pedals away from your
body.
The vehicle must be in PARK (P) for this
feature to operate.
See Section 2 of your Owner Manual.
A
B