2004 DAEWOO NUBIRA section 9G

BODY REAR END 9S – 3
DAEWOO V–121 BL4
4. Remove the lower B–pillar seat belt bolt and the
anchor.
5. Remove the screw and the fuel filler door remote
cable handle cover.
6. Remove the screws and the fuel filler door remote
cable handle.
7. Disconnect the cable from the handle.
8. Remove the driver’s side seat and the rear seats.
Refer to Section 9H, Seats.
9. Remove the left side front and rear rocker panels,
the left side kick panel, and the left side lower B–
pillar trim panel. Refer to Section 9G, InteriorTrim.
10. Reposition the floor carpet on the left side of the
vehicle.
11. Remove the cable.
Installation Procedure
1. Feed the cable from the luggage compartment to
the passenger compartment.
2. Install the floor carpet to its original position.
3. Install the left side front and rear rocker panels, the
left side kick panel, and the left side lower B–pillar
trim panel. Refer to Section 9G, Interior Trim.
4. Install the driver’s side seat and the rear seats. Re-
fer to Section 9H, Seats.
5. Connect the cable to the handle.
Notice : Dissimilar metals in direct contact with each other
may corrode rapidly. Make sure to use the correct fasten-
ers to prevent premature corrosion.
6. Install the fuel filler door remote cable handle with
the screws.
Tighten
Tighten the fuel filler door remote cable handle screws
to 10 NSm (89 lb–in).
Notice : Dissimilar metals in direct contact with each other
may corrode rapidly. Make sure to use the correct fasten-
ers to prevent premature corrosion.
7. Install the fuel filler door remote cable handle cover
with the screw.
Tighten
Tighten the fuel filler door remote cable handle cover
screw to 3 NSm (27 lb–in).

9S – 4IBODY REAR END
DAEWOO V–121 BL4
8. Install the lower B–pillar seat belt anchor with the
bolt.
Tighten
Tighten the lower B–pillar seat belt anchor bolt to 38
NSm (28 lb–ft).
9. Connect the cable to the fuel filler door.
10. Install the luggage compartment wheelhouse trim
panels and the luggage compartment rear trim pan-
el. Refer to Section 9G, Interior Trim.
11. Close the luggage compartment.
REAR DECK LID
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the electrical connector.
3. Remove the electrical harness from the rear deck
lid hinge arm.
4. Remove the bolts and the rear deck lid.
Installation Procedure
Notice : Dissimilar metals in direct contact with each other
may corrode rapidly. Make sure to use the correct fasten-
ers to prevent premature corrosion.
1. Install the rear deck lid with the bolts.
Tighten
Tighten the rear deck lid bolts to 10 NSm (89 lb–in).
2. Install the electrical harness to the rear deck lid
hinge arm.
3. Connect the electrical connector.
4. Connect the negative battery cable.

9S – 6IBODY REAR END
DAEWOO V–121 BL4
LUGGAGE COMPARTMENT LOCK
STRIKER
Removal Procedure
1. Open the luggage compartment.
2. Remove the luggage compartment rear lower cov-
er. Refer to Section 9G, Interior Trim.
3. Remove the bolts securing the lock striker.
4. Pull the lock striker out.
5. Disconnect the lock release cable from the lock
striker.
Installation Procedure
1. Connect the lock release cable.
Notice : Dissimilar metals in direct contact with each other
may corrode rapidly. Make sure to use the correct fasten-
ers to prevent premature corrosion.
2. Install the lock striker with the bolts.
Tighten
Tighten the luggage compartment lock striker bolts to
8 NSm (71 lb–in).
3. Install the luggage compartment rear lower cover.
Refer to Section 9G, Interior Trim.
LUGGAGE COMPARTMENT LOCK
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the luggage compartment lock cover.
3. Disconnect the electrical connector.
4. Remove the screws and the luggage compartment
lock.
5. Disconnect the lock rod.
Installation Procedure
1. Connect the lock rod.
Notice : Dissimilar metals in direct contact with each other
may corrode rapidly. Make sure to use the correct fasten-
ers to prevent premature corrosion.
2. Install the luggage compartment lock with the
screws.
Tighten
Tighten the luggage compartment lock screws to 6
NSm (53 lb–in).
3. Connect the electrical connector.
4. Install the luggage compartment lock cover.
5. Connect the negative battery cable.

BODY REAR END 9S – 7
DAEWOO V–121 BL4
WEATHERSTRIP
Removal Procedure
1. Open the luggage compartment lid.
2. Remove the weatherstrip from around the gutter.
Installation Procedure
1. Install the weatherstrip onto the gutter flange.
2. Inspect the weatherstrip. Make sure that the clinch
is completely seated onto the flange.
3. Using a water hose without a nozzle, test the rear
deck lid to make sure that no leaks are present.
S If there are no leaks present, no further repair is
required.
S If leaks are present, continue with the remainder
of the installation procedure.
J4D39S01
HATCHBACK WEATHERSTRIP
Removal Procedure
1. Open the luggage compartment lid.
2. Remove the luggage compartment rear quarter and
rear trim panels. Refer to Section 9G, Interior Trim.
3. Remove the weatherstrip from around the gutter.
J4D39S01
Installation Procedure
1. Install the weatherstrip onto the gutter flange.
2. Inspect the weatherstrip. Make sure that the clinch
is completely seated onto the flange.
3. Using a water hose without a nozzle, test the rear
deck lid to make sure that no leaks are present.
4. Install the luggage compartment rear quarter and
rear trim panels. Refer to Section 9G, Interior Trim.

9S – 8IBODY REAR END
DAEWOO V–121 BL4
J4D39S02
HATCHBACK DOOR
Removal Procedure
1. Open and suitably support the hatchback door.
2. Disconnect the hatchback door grommet, the elec-
trical connector, and the washer hose.
3. Remove the gas support assemblies from the
hatchback door and the body. Refer to ”Gas Sup-
port Assemblies” in this section.
4. With the aid of another technician, remove the bolts
and the hatchback door from the hinges.
J4D39S02
Installation Procedure
1. With the aid of another technician, install the hatch-
back door to the hinges with the bolts.
Tighten
Tighten the hatchback door hinge bolts to 20 NSm (15
lb–ft).
2. Install the gas support assemblies to the hatchback
door and the body. Refer to ”Gas Support Assem-
blies” in this section.
3. Connect the hatchback door electrical connector,
the washer hose, and the grommet.
4. Close the hatchback door.
GAS SUPPORT ASSEMBLIES
Removal Procedure
1. Open and suitably support the hatchback door.
2. Unscrew and remove the gas support assembly
from the hatchback door and the body.
Installation Procedure
1. Install the gas support assembly onto the hatch-
back door and the body.
Tighten
Tighten the gas support assembly studs to 8 NSm (71
lb–in).
2. Close the hatchback door.

BODY REAR END 9S – 9
DAEWOO V–121 BL4
HATCHBACK DOOR LOCK STRIKER
Removal Procedure
1. Open the hatchback door.
2. Remove the luggage compartment rear trim panel.
Refer to Section 9G, Interior Trim.
3. Remove the screws that secure the lock striker.
4. Disconnect the cable from the lock striker.
Installation Procedure
1. Connect the cable to the lock striker.
2. Install the lock striker with the screws.
Tighten
Tighten the hatchback door lock striker screws to 20
NSm (15 lb–ft).
3. Install the luggage compartment rear trim panel.
Refer to Section 9G, Interior Trim.
4. Close the hatchback door.
J4D39S04
HATCHBACK DOOR LOCK
Removal Procedure
1. Open the hatchback door.
2. Remove the hatchback door lower garnish molding.
Refer to Section 9G, Interior Trim.
3. Remove the screws and the hatchback lock.
4. Disconnect the lock rods and the electrical connec-
tor.
J4D39S04
Installation Procedure
1. Connect the lock rods and the electrical connector.
2. Install the hatchback lock with the screws.
Tighten
Tighten the hatchback door lock screws to 6 NSm (53
lb–in).
3. Install the hatchback door lower garnish molding.
Refer to Section 9G, Interior Trim.
4. Close the hatchback door.

SECTION : 9T1
REMOTE KEYLESS ENTRY AND ANTI–THEFT
SYSTEM
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS 9T1–1 . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 9T1–1. . . . . . . . . .
SCHEMATIC AND ROUTING DIAGRAMS9T1–2 . . . .
Notchback Remote Keyless Entry and Anti–Theft
System 9T1–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hatchback Remote Keyless Entry and Anti–Theft
System 9T1–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Module/Receiver Connector 9T1–4. . . . . . . . .
MAINTENANCE AND REPAIR9T1–5 . . . . . . . . . . . . . .
ON–VEHICLE SERVICE 9T1–5. . . . . . . . . . . . . . . . . . . .
Control Module/Receiver 9T1–5. . . . . . . . . . . . . . . . . . .
Siren (General Only) 9T1–5. . . . . . . . . . . . . . . . . . . . . . Remote Keyless Entry Transmitter
Programming 9T1–7. . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION9T1–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Keyless Entry and Anti–Theft System 9T1–8
Remote Locking and Unlocking 9T1–8. . . . . . . . . . . . .
Security Indicator 9T1–8. . . . . . . . . . . . . . . . . . . . . . . . .
Intrusion Sensing 9T1–8. . . . . . . . . . . . . . . . . . . . . . . . .
Siren (General Only) 9T1–8. . . . . . . . . . . . . . . . . . . . . .
Vehicle Locator 9T1–8. . . . . . . . . . . . . . . . . . . . . . . . . . .
Autolocking (Safety Lock) 9T1–9. . . . . . . . . . . . . . . . . .
Control Module/Receiver 9T1–9. . . . . . . . . . . . . . . . . . .
Fault or Alarm Indication 9T1–9. . . . . . . . . . . . . . . . . . .
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNSmLb–FtLb–In
Siren Braket Mounting Bolts.8–71

REMOTE KEYLESS ENTRY AND ANTI–THEFT SYSTEM 9T1 – 5
DAEWOO V–121 BL4
MAINTENANCE AND REPAIR
ON–VEHICLE SERVICE
CONTROL MODULE/RECEIVER
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the floor console. Refer to Section 9G,
Interior Trim.
3. Disconnect the control module/receiver electrical
connector.
4. Slide the control module/receiver away from its
mounting bracket.
Installation Procedure
1. Install the control module/receiver on its mounting
bracket.
2. Connect the control module/receiver electrical con-
nector.
3. Install the floor console. Refer to Section 9G, Inte-
rior Trim.
4. Connect the negative battery cable.
SIREN (GENERAL ONLY)
Removal Procedure
1. Remove the siren electrical connector.
2. Remove the siren bracket mounting bolts and siren.