2004 DAEWOO NUBIRA display

ENGINE CONTROLS 1F – 291
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
101. Replace the ECM.
2. Turn the ignition OFF for 10 seconds.
3. Clear any DTCs from ECM.
4. Turn the ignition switch to ON.
Does the fuel pump operate?2.55 secondsSystem OKGo to Step 11
111. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC ad specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 12Go to Step 2
12Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

1F – 294IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
101. Replace the ECM.
2. Turn the ignition OFF for 10 seconds.
3. Clear any DTCs from ECM.
4. Turn the ignition switch to ON.
Does the fuel pump operate?2.55 secondsSystem OKGo to Step 11
111. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC ad specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 12Go to Step 2
12Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

1F – 296IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Remove the crankshaft.
2. Check for a problem with the crahkshaft’s visu-
al defection and tooth.
Is a problem found?–Go to Step 5Go to Step 6
5Replace the crankshaft.
Is the replacement complete?–System OK–
61. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 7–
71. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as supported in the text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 8Go to Step 2
8Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 298IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
5Replace the crankshaft.
Is the replacement complete?–System OK–
61. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 7–
71. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as supported in the text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 8Go to Step 2
8Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 300IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1382 – Rough Road Data Invalid (NON ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with engine OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Review and record the scan tool Failure Re-
cords data.
4. Operate the vehicle within Failure Records
conditions as noted.
5. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1382.
Does the scan tool indicate that DTC P1382 failed?–Go to Step 4Go to Step 3
31. Check for the following conditions and repair as
needed:
2. VR sensor seal missing or damaged.
3. VR sensor mounting flanges cracked, missing,
or incorrectly installed.
Is the repair complete?–Go to Step 14Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the VR sensor electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Observe the VR sensor value displayed on the
scan tool.
Is the VR sensor value near the specified value?0VGo to Step 5Go to Step 12
51. Jumper the 5 volt reference circuit, terminal 2
and the VR sensor signal circuit, terminal 1 to-
gether at the VR sensor harness connector.
2. Observe the VR sensor value displayed on the
scan tool.
Is the VR sensor value near the specified value?4.95VGo to Step 14Go to Step 10
61. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
and check the sensor ground circuit for high
resistance, an open between the ECM and the
VR sensor, or for a poor connection at the ter-
minal 53 of the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 10
7Check the 5 volt reference circuit for high resistance,
an open between the ECM and the VR sensor, or a
poor connection at the terminal 84 of the ECM and
repair as needed.
Is the repair complete?–Go to Step 14Go to Step 8
81. Turn the ignition OFF.
2. Disconnect the ECM and check the VR sensor
signal circuit for high resistance, an open, a low
voltage, or a short to the sensor ground circuit
and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 9

ENGINE CONTROLS 1F – 301
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
9Check the VR sensor signal circuit for a poor con-
nection at the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 13
10Check for a poor connection at terminal 1 of the VR
sensor and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 11
11Replace the VR sensor.
Is the repair complete?–Go to Step 14–
121. Turn the ignition OFF.
2. Disconnect the ECM.
3. Turn the ignition ON.
4. Check the VR sensor signal circuit for a short
to battery voltage or a short to the 5 volt refer-
ence circuit and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 13
131. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 14–
141. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 15Go to Step 2
15Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 303
DAEWOO V–121 BL4
DTC P1382 – Rough Road Data Invalid (ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with engine OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Review and record the scan tool Failure Re-
cords data.
4. Operate the vehicle within Failure Records
conditions as noted.
5. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1382.
Does the scan tool indicate that DTC P1382 failed?–Go to Step 4Go to Step 3
31. Check for the following conditions and repair as
needed:
2. Wheel speed sensor seal missing or damaged.
3. Wheel speed sensor mounting flanges
cracked, missing, or incorrectly installed.
Is the repair complete?–Go to Step 14Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the defected Wheel speed sensor
electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Observe the Wheel speed sensor value dis-
played on the scan tool.
Is the Wheel speed sensor value near the specified
value?0VGo to Step 5Go to Step 12
51. Jumper the 5 volt reference circuit, the Wheel
speed sensor signal circuit, together at the de-
fected Wheel speed sensor harness connector.
2. Observe the defected Wheel speed sensor val-
ue displayed on the scan tool.
Is the VR sensor value near the specified value?4.95VGo to Step 14Go to Step 10
61. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
and check the sensor ground circuit for high
resistance, an open between the ECM and the
Wheel speed sensor, or for a poor connection
of the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 10
7Check the 5 volt reference circuit for high resistance,
an open between the ECM and the Wheel speed
sensor, or a poor connection of the ECM and repair
as needed.
Is the repair complete?–Go to Step 14Go to Step 8

1F – 304IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
81. Turn the ignition OFF.
2. Disconnect the ECM and check the Wheel
speed sensor signal circuit for high resistance,
an open, a low voltage, or a short to the sensor
ground circuit and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 9
9Check the Wheel speed sensor signal circuit for a
poor connection at the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 13
10Check for a poor connection at the Wheel speed
sensor and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 11
11Replace the Wheel speed sensor.
Is the repair complete?–Go to Step 14–
121. Turn the ignition OFF.
2. Disconnect the ECM.
3. Turn the ignition ON.
4. Check the Wheel speed sensor signal circuit
for a short to voltage or a short to the 5 volt
reference circuit and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 13
131. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 14–
141. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 15Go to Step 2
15Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK