2004 DAEWOO LACETTI ignition

1F – 550IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1336
58X CRANK POSITION TOOTH ERROR NOT LEARNED
Circuit Description
In order to detect engine misfire at higher engine speeds,
the Engine Control Module (ECM) must know of any varia-
tion between the crankshaft sensor pulses. Most varia-
tions are due to the machining of the crankshaft reluctor
wheel. However, other sources of variation are also pos-
sible. A Crankshaft Position (CKP) system variation learn-
ing procedure must be performed any time a change is
made to the crankshaft sensor to crankshaft relationship
of if the ECM is replaced or reprogrammed. The ECM
measures the variations and then calculates compensa-
tion factors needed to enable the ECM to accurately de-
tect engine misfire at all speeds and loads. A scan tool
must be used to command the ECM to learn these varia-
tions. If for any reason the ECM is unable to learn these
variations or they are out of an acceptable range, the ECM
will set Diagnostic Trouble Code (DTC) P1336. An ECM
that has not had the CKP system variation learning proce-
dure performed due to replacement or reprogramming will
also set DTC P1336.
Conditions for Setting the DTC
S Tooth error not learned if the manufacture enable
counter is set to zero.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0132, P0201, P0202, P0203,
P0204, P0325 , 0327, P0336, P0337, P0341,
P0342, P0351, P0352, P0402, P1404, P0404,
P0405, P0406 and P0502 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffer.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF after four consecutive igni-
tion cycles in which the diagnostic runs without a
fault.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Disconnecting the ECM battery feed for more than
10 seconds.
S DTC(s) can be cleared by using the scan tool.Diagnostic Aids
CAUTION : To avoid personal injury when performing
the crankshaft position system variation learning
procedure, always set the vehice parking brake and
block the drive wheels. Release the throttle immedi-
ately when the engine starts to decelerate. Once the
learn procedure is completed, engine control will be
returned to the operator, and the engine will respond
to throttle position.
DTC P1336 will only set if the ECM has not learned the
CKP system variation. The ECM only needs to learn this
variation once per life cycle of the vehicle unless the crank
sensor to crankshaft relationship is disturbed. Removing
a part is considered a disturbance. A fully warmed engine
is critical to learning the variation correctly. If a valid learn
occurs, no other learns can be completed that ignition
cycle.
If the engine cuts out before the specified learn procedure
engine speed or at normal fuel cutoff rpm, the ECM is not
in the learn procedure mode.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the fault occurred. The information is then stored on
the scan tool for later reference.
2. Engine temperature is critical to properly learn the
CKP system variation. Failure to properly warm the
engine before performing this procedure will result
in an inaccurate measurement of the CKP system
variation. The ECM learns this variation as the en-
gine is decelerating and then allows engine control
to be returned to the operator. All accessories must
be OFF when learning the CKP system angle varia-
tion. If the A/C is not disabled when the learn pro-
cedure is enabled, the ECM will disable the A/C.
3. If after the specified number attempts the ECM
cannot learn the CKP system variation, then the
variation is too large and no further attempts should
be made until the variation problem is corrected.
4. Being unable to learn the procedure indicates that
the variation is out of range.
5. After the CKP system variation has been learned,
wait above 10 seconds with ignition switch OFF to
prevent being cleared the learned value.

ENGINE CONTROLS 1F – 551
DAEWOO V–121 BL4
DTC P1336 – 58X Crank Position Tooth Error Not Learned
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Put the vehicle in PARK or NEUTRAL.
4. Start the engine and operate to normal operat-
ing temperature.
5. Turn all accessories OFF.
6. Enable the TEC (Tooth Error Correction)
LEARN PROCEDURE with the scan tool.
7. Raise the engine rpm to the specified value,
then release the throttle as soon as the engine
cuts out.
Does the scan tool indicate that the Crankshaft Posi-
tion (CKP) system variation has been learned?65°C (149°F)
4000 rpmGo to Step 5Go to Step 3
3Attempt the CKP system variation procedure as
many times as the specified value.
Does the scan tool indicate that the CKP system
variation has been learned?10Go to Step 5Go to Step 4
4Check for a problem with the CKP sensor to crank-
shaft relationship.
Is the repair complete?–Go to Step 5–
51. Turn the ignition OFF and wait above specified
value.
2. Turn the ignition ON, with engine OFF.
3. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
4. Start the engine and idle at normal operating
temperature.
5. Operate the vehicle within the conditions for
setting this DTC as supported in the text.
Does the scan tool indicate that this diagnostic ran
and passed?10 secGo to Step 6Go to Step 2
6Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 553
DAEWOO V–121 BL4
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. The On–Board Diagnostic (EOBD) System Checkprompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
DTC P1391 – G Sensor Rough Road Rationality
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with engine OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Review and record the scan tool Failure Re-
cords data.
4. Operate the vehicle within Failure Records
conditions as noted.
5. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1391.
Does the scan tool indicate that DTC P1391 failed?–Go to Step 4Go to Step 3
3Check for the following conditions and repair as
needed:
S G sensor seal missing or damaged.
S G sensor mounting flanges cracked, missing,
or incorrectly installed.
Is the repair complete?–Go to Step 14Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the G sensor electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Observe the G sensor value displayed on the
scan tool.
Is the G sensor value near the specified value?0 vGo to Step 5Go to Step 12
51. Jumper the 5 volt reference circuit, terminal A
and the G sensor signal circuit, terminal B to-
gether at the G sensor harness connector.
2. Observe the G sensor value displayed on the
scan tool.
Is the G sensor value near the specified value?4.95 vGo to Step 6Go to Step 7
61. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
and check the sensor ground circuit for high
resistance, an open between the ECM and the
G sensor, or for a poor connection at the termi-
nal k34 of the ECM and repair as needed.
3. f the problem is found, repair as necessary.
Is a problem found?–Go to Step 14Go to Step 10
7Check the 5 volt reference circuit for high resistance,
an open between the ECM and the G sensor, or a
poor connection at the terminal k50 of the ECM and
repair as needed.
Is the repair complete?–Go to Step 14Go to Step 8

1F – 554IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
81. Turn the ignition OFF.
2. Disconnect the ECM and check the G sensor
signal circuit for high resistance, an open, a
short to ground, or a short to the sensor ground
circuit and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 9
9Check the G sensor signal circuit for a poor connec-
tion at the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 13
10Check for a poor connection at terminal C of the G
sensor and repair as needed.
Is the repair complete?Go to Step 14Go to Step 11
11Replace the G sensor.
Is the repair complete?–Go to Step 14–
121. Turn the ignition OFF.
2. Disconnect the ECM.
3. Turn the ignition ON.
4. Check the G sensor signal circuit for a short to
voltage or a short to the 5 volt reference circuit
and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 13
131. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 14–
141. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 15Go to Step 2
15Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 556IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1392 – G Sensor Rough Road Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Turn the ignition ON, with the engine OFF.
4. Observe the ROUGH ROAD value displayed
on the scan tool.
Is the ROUGH ROAD value near the specified val-
ue?0 vGo to Step 4Go to Step 3
31. Review and record the scan tool Failure Re-
cords data.
2. Operate the vehicle within Failure Records
conditions as noted.
3. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1392.
Does the scan tool indicate that DTC P1392 failed?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the G sensor electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Jumper the 5 volt reference circuit, terminal A
and the G sensor signal circuit, terminal B to-
gether at the G sensor harness connector.
5. Observe the G sensor value displayed on the
scan tool.
Is the G sensor value near the specified value?4.95 vGo to Step 9Go to Step 5
51. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
and check the 5 volt reference circuit for an
open or short to ground and repair as needed.
Is the repair complete?–Go to Step 11Go to Step 6
6Check the 5 volt reference circuit for poor connection
at the ECM and repair or replace as needed.
Is the repair complete?–Go to Step 11Go to Step 7
71. Turn the ignition OFF.
2. Disconnect the ECM and check the G sensor
signal circuit for an open, a short to ground, or
a short to the sensor ground circuit and repair
as needed.
Is the repair complete?–Go to Step 11Go to Step 8
8Check the G sensor signal circuit for a poor connec-
tion at the ECM and repair as needed.
Is the repair complete?–Go to Step 11Go to Step 10
9Replace the G sensor.
Is the repair complete?–Go to Step 11–
101. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 11–

ENGINE CONTROLS 1F – 559
DAEWOO V–121 BL4
DTC P1393 – G Sensor Rough Road High Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Start and idle the engine.
4. Observe the ROUGH ROAD value displayed
on the scan tool.
Is the ROUGH ROAD value near the specified val-
ue?4.5 vGo to Step 4Go to Step 3
31. Review and record the scan tool Failure Re-
cords data.
2. Operate the vehicle within Failure Records
conditions as noted.
3. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1393.
Does the scan tool indicate that DTC P1393 failed?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the G sensor electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Note the G sensor voltage displayed on the
scan tool.
Is the G sensor value near the specified value?0 vGo to Step 5Go to Step 6
5Probe the sensor ground circuit terminal C with a test
light to B+.
Is the test light ON?–Go to Step 7Go to Step 9
6Check the G sensor signal circuit for a short to volt-
age or a short to the 5 volt reference circuit and re-
pair as needed.
Is the repair complete?–Go to Step 12Go to Step 11
7Check for a poor sensor ground terminal connection
at the G sensor electrical connector.
Is the repair complete?–Go to Step 12Go to Step 8
8Check for a poor sensor ground terminal connection
at the Engine Control Module (ECM) and repair as
needed.
Is the repair complete?–Go to Step 12Go to Step 10
9Check the G sensor ground circuit for an open and
repair as needed.
Is the repair complete?–Go to Step 12Go to Step 10
101. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 12–
11Replace the G sensor.
Is the repair complete?–Go to Step 12Go to Step 10

1F – 562IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1396 – ABS WSS Signal Variation
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with the engine OFF.
2. Install a scan too.
Are any additional Diagnostic Trouble Codes
(DTCs) set?–Go to
applicable DTC
tableGo to Step 3
31. Review and record the scan tool Failure Re-
cords data.
2. Operate the vehicle within Failure Records
conditions as noted.
3. Using the scan tool, monitor specific DTC info
for DTC P1391.
Does the scan tool indicate that DTC P1391 failed?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the engine control module (ECM)
and check for an open or short in the wire be-
tween ECM connector terminal K7 and Elec-
tronic Brake Control Module (EBCM) connector
terminal 25.
Is the problem found?–Go to Step 5Go to Step 6
5Repair an open or short in the wire between ECM
connector terminal K7 and EBCM connector termi-
nal 25.
Is the repair complete?–Go to Step 7–
61. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 7–
71. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as supported in the text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 8Go to Step 2
8Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 564IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1397 – ABS WSS No Signal
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with the engine OFF.
2. Install a scan too.
Are any additional Diagnostic Trouble Codes
(DTCs) set?–Go to
applicable DTC
tableGo to Step 3
31. Review and record the scan tool Failure Re-
cords data.
2. Operate the vehicle within Failure Records
conditions as noted.
3. Using the scan tool, monitor specific DTC info
for DTC P1391.
Does the scan tool indicate that DTC P1391 failed?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the engine control module (ECM)
and check for an open or short in the wire be-
tween ECM connector terminal K7 and Elec-
tronic Brake Control Module (EBCM) connector
terminal 25.
Is the problem found?–Go to Step 5Go to Step 6
5Repair an open or short in the wire between ECM
connector terminal K7 and EBCM connector termi-
nal 25.
Is the repair complete?–Go to Step 7–
61. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 7–
71. Using the scan tool, clear the DTCs.
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as supported in the text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 8Go to Step 2
8Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK