2004 DACIA SOLENZA window

61
HEATING
61 - 9
Control cables
DISMOUNTING
Dismounting of the control cables ( 1) may be performed without dashboard dismounting .
Dismo unt :
- ashtray;
- switches of the front doors electric windows;
- control panel as well as cables ( 1) attached to this one by screws.
Dismount the maintaining clips (2) in the cockpit lower part.
Release the cables.
1 2
R
EMOU NT I NG
Perform the dismounting operations in the reverse order.
Check the good operation of the controls.
Remount the control panel on the dashboard and central console.
continuity and resistance against vehicle’s mass,
front wiring between:
- cockpit fuse F 14 exit pin 7 climate control panel
- pin 9 climate control panel vehicle mass.
vnx.su

62
AIR CONDITIONING
62 - 5
Operating principle
The climate control assembly is enabling outside air penetration in the vehicle climate control
unit.
Climate controls:
A – air temperature adjustment
B – air distribution in the cockpit
C – air quantity adjustment in cockpit
Air temperature adjustment
Control knob (A) is enabling the obt aining of t he de sired tempera ture in t he cockpit. By
turning to the right the knob (A), the air temperature is increasing.
Air distribution in the cockpit
Ai r distribution in the cockpit is obtained by means of rotating t he knob (B) in the desired
position.
Position
Airflow is directed towards the dashboard air vents.
Position
Airflow is directed towards all dashboard air vents and passengers l egs.
Position
Airflow is directed towards passengers legs.
Position
Airflow is directed between all a ir vents, front side windows defrosting vents, windscreen
defrosting vent and passenger legs.
Position
Entire airflow is directed towards windscreen and side windows defrosting air vents. For a
more substantial efficiency, close the dashboard air vents.
A B
D EC
vnx.su

62
AIR CONDITIONING
62- 6
Operating principle
Air quantity adjustment in c ockpit
The flow of circulating air in cockpit is adjusted by rotating the (C) knob in the correspondin g
positions for the four speed steps of the blower. The more speed step is bigger the more airflow
is bigger.
For a be tter effi ciency of the windscreen defrosting or de fogging, t he (C ) knob m ust be
placed on the last position. In order to complete closing of the cold air penetration, rotate the knob on “ 0” position.
Air conditioning AC
When pushing the (D) button, the starting / stopping of the air conditioning is ensured. If ( D)
button is not pushed, the air conditioning is not working, ventilation being identical to the one of
a vehicle without air conditioning.
The use of air conditioning is enabling:-lowering the a ir temperature i n cockpit when the vehicle i s driven in sunny places or
when the vehicle is stopped in the sunshine; -reducing the humidity in cockpit (event facilitated by defogging).
Air conditioning can not be used at low outside temperatures. During air conditioning operatio n,
for a better efficiency, all windows must be closed.
R ecycled air
When pushing the ( E) button, the climate maintenance unit is working with cockpit recycled
air, without outside air penetration.
Air recycli ng is enabling:
- isolation from outside atmosphere;
-f aster reaching the desired temperature in cockpit.
Prolonged use of this function may lead to glasses fogging. Normal operation returning, with
outside air, is t hen imposed, by pushing the (E) button stopping the cockpit air recycling.
A B
D EC
vnx.su

66
66 - 1
GLASSES SEALING
Glasse s gaskets
1. Windscreen gasket
2. Hatchback gasket
3. Fix window gasket
4. Doors glasses gaskets kit.
10 cm
5
8
67
4
1 3
2
DISMOUNTIN
G
Dismount the windscreen and hatchback
glass, together with the gasket by pushing from
the inside of the vehicle. If reused, the glass gasket shall be c leaned
or replaced with a new one.
R EMOU NT I NG
Place the gasket (6) all around the glass (5).
Apply in the gasket channelin the contact area
with carriage body a cord of sealaling material
Ro mtix 1502 P 3 mm di ameter. Int roduce a
cotton cord (8) of 3 – 4 mm diameter has been
previously introduced, leaving at the ends (7)
about 20 mm of cord, and between the ends,
the distance shall be not more than 10 mm. ATTENT ION:
Check if the gasket draining holes are
pierced.
vnx.su

66
66 - 2
GLASSES SEALING
Inside wipers
INSI DE WIPERS
DISMOUNTIN G
Dismount :
- opening handle;
- window regulator crank;
- inside door opening mechanism;
- panel attachment screws.
Remove the inside wiper.
R EMOU NT I NG
Perform the dismounting operations in the reverse order.
vnx.su

66
66 - 3
GLASSES SEALING
DISMOUNTIN G
Lower the window in the minimum position.
Dismount the outside wiper (1), by detaching it from the clips (2).
REMOU NT I NG
Perform in the reverse order the dismounting operation.
Outside wipers
vnx.su

72
72 - 1
LATERAL OPENINGS TRIMS
Front door panel
DISMOUNTIN G
Disconnect the battery.
Dismount :
- window regulator crank (A) for glass
lifting , that is mounted by clips attachment on
the window regulator axle ( in case of the
vehicles provided with glass hand-drive lifting);
- attachment screw of the open ing
mechanism from inside (B), consequently the
mechanism. - locking handle (C) attached by screw.
Rotate the speaker grill (D) counter clock-
wise direction and extract it from the front door
panel.
Dismount the four attachmen t screws of the
s peaker on the door pa nel.
Disco n n ect the front door speaker
connector. Dismount the attachment screws (1 ) of the
door panel on the caisson.
D C
1
1
CD 1
2
B
A
Detach from clips the door panel in poi nts
(2) .
R EMOU NT I NG
Perform in the reverse order the dismounting
operations taking i nto account t he following
recommendations: - check the integrity of the deflective
panel and of the continuos layer of Romtix
1502 P sealing materi al on the front door
caisson; - for the mounting of the inside opening
mechanism, the opening control rod will be
placed in the position where the assemble d plate
with electric control is blocked;
- after mounting, check the operation of
the inside opening mechanism and its alignment
with the front door panel; - check t he ope ration of t he front door
speaker.
vnx.su

72
72 - 2
LATERAL OPENINGS TRIMSRear door panel
1 C
B
1A 2
C
2
DISMOUNTIN
G
Dismount :
- window regulator cra nk (A) for glass
lifting that is mounted by clips attachment on
the window regulator axle.
- attachment screw of the inside opening
mechanism (B), consequently, the mechanism;
- locking handle (C) attached by screw;
- attachment screws (1) of the rear door
panel on the caisson; Detach from clips the rear door panel from
points (2).
REMOU NT I NG
Perform the dismounting operations in the
reverse orde r, taking into considera tion the
followings recommendations: - check the integrity of the deflectiv e panel
and of the continuos sealant material layer
Romt ix 1502 P on the door caisson outliner;
- for the mounting of the inside opening
mechanism, the opening control rod will be
placed in the position where the assemble d plate
with electric control is unblocked. - after mounting, check the operation of
the inside opening mechanism and its alignment
w ith the rear door panel.
vnx.su