2004 Citroen XSARA no pegs

Downloaded from www.Manualslib.com manuals search engine 118
ENGINE
B1BP2LSCB1BP2LTC
AUXILIARY EQUIPMENT DRIVE BELT
Engines: HFX KFV NFU
Tools.
[1]
Pliers for removing plastic pegs: 7504 –T
[2] Belt tension measuring instrument: 4122T
V
ehicle without air conditioning.
Refit.
Refit the belt.
Respect the following sequence:
Crankshaft pinion.
Alternator pulley.Place tool
[2]on the belt.
Tighten screw (1)to achieve a tension of:55 ± 3 SEEM units.Tighten:
Screw (3).
Screw (2).
Remove tool [2]and complete the refitting.
Remove.
Slacken:
Screw
(2). Screw (3). Tensioning screw (1).
Push the alternator back towards the engine.
Remove the belt.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 120
ENGINE
B1BP234C
XSARA PICASSOAUXILIARY EQUIPMENT DRIVE BELT
Engine: NFV
Without air conditioning.
Tools.
[1]Pliers for removing plastic pegs: 7504 –T
[2]Belt tension measuring instrument: 4122 –T
[3]TORX spanner
Remove. Release the central screw (1),tool [3] Detension the tensioner roller (2), (flat spanner 27 on flat).
Remove the belt.
Refit. Position the belt.
Hold the belt in position using the tensioner roller (2).
Pretension the belt 120 SEEM units, tool [2].
Lock the central screw (1),tool [3].
Remove the tool [2].
Rotate the crankshaft 2to 4times.
Check the tension, 120 SEEM units.
If not, restart the operation.

Downloaded from www.Manualslib.com manuals search engine 121
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: NFV
With air conditioning.
XSARA PICASSO
B1BP235C
Tools.
[1]
Pliers for removing plastic pegs: 7504 –T
[2] Belt tension measuring instrument: 4122 –T
[3] 10 mm square (drain spanner)[4] TORX spanner
Remove. Detension the automatic tensioner, tool[3]. Place aØ 6 mm peg at(a) to immobilise the automatic tensioner.
Remove the belt.
Refit. Position the belt
Detension the automatic tensioner, tool[3]. Remove theØ 6 mm peg.
Release the automatic tensioner.
Remove the tool
[3].

Downloaded from www.Manualslib.com manuals search engine 123
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: KFU
B1BP2LTC
Tools.
[1]Plyers for removing plastic pegs: 7504 –T
[2]Belt tension measuring instrument (SEEM): 4122 –T
Removing.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.
Remove the front RH wheel and the front RH splashshield, using tool
[1].
Vehicle without air conditioning.Removing.Slacken the tension, screw(2), screw (3)and screw(1).
Push back the alternator towards the engine.
Remove the auxiliary equipment drive belt.
Refitting.Refit the auxiliary equipment drive belt.
Respect the following sequence :
Crankshaft pinion, alternator pulley.
Position tool
[2]on the belt. Tighten the screw (1)to tension the belt to 55 ±3 SEEM units. Tighten screw (3), screw (2).
Remove tool [2]. Complete the refitting in the opposite order to removal.
B1BP2LSC
C3

Downloaded from www.Manualslib.com manuals search engine 128
ENGINEAUXILIARY EQUIPMENT DRIVE BELT 2002
Engines: 6FZ RFN
Without air conditioning.With air conditioning.
Tools.
[1]
Pliers for removing plastic pegs :7504T
Remove the belt.
Detension the belt (3)by turning the screw (2)of the tensioner roller (1)(anticlockwise).
The screw
(2) (WARNING: not left hand screw).
Remove the belt (3), while keeping the tensioner roller (1)tight.
Refit the belt. Refit the belt (3), while keeping the tensioner roller (1)tight.
Release the tensioner roller (1).
B1BP23PCB1BP23QCB1BP23PCB1BP23RC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 135
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 8HX 8HW
With compressor and alternator .
B1BP2MKCB1BP2MJD
Tools.
[1]
Pliers for removing plastic pegs: 7504T
[2]Tensioner roller compression lever:().0194.E
[3]Tensioner roller setting peg Ø4 mm: ().0194.F
Removing.
Disconnect the battery negative cable.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel.
Move aside the splashshield, using tool
[1].
IMPERATIVE: In the case of belt reuse, mark the
direction of rotation of the belt. If the index on the
tensioner roller is outside the marks, change
the auxiliary equipment drive belt.
The alternator (1).
The aircon compressor (2).
Detension the auxiliary belt tensioner roller, using tool [2].
Position the peg [3].
Remove the auxiliary drive belt.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine ENGINE
149
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
B1BP2MAC
Checking the timing (continued).
Engine:
NFU.
Place a jack under the engine, peg the engine.
Remove:
The engine support
(4)complete.
The timing casing
(3).
The sparking plugs
(eases engine rotation).
Turn the wheel to rotate the engine
(normal direction of rotation).
Position the pegs
[3a]and[3b].
Peg the flywheel, using tool
[1].
If the setting is not correct, recommence the operation.
Remove the tools
[1], [2], [3a]and [3b].
Complete the refitting.
B1BP2MBCB1EP18MC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 154
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: HFX KFV
B1EP18QC
Setting the timing (continued).
Engines:
HFXKFV.
Refit.
WARNING: Respect the direction of fitting of the belt
(the arrows «d» indicate the direction of rotation
of the crankshaft).
Refit the timing belt.
Position the timing belt, belt
«e»well tensioned, in the following order:
Crankshaft pinion, hold the belt using tool [5].
Camshaft pulley.
Coolant pump pulley. Tensioner roller.
Remove the pegs
[1]and [2].
C2 C3 C3 PLURIEL