2004 Citroen XSARA rear

Downloaded from www.Manualslib.com manuals search engine 382
AXLES
SUSPENSION
STEERING
ESSENTIAL: When checking the suspensions, the vehicle should be at reference height.
XSARA
AXLE GEOMETRY
Values of the front and rear suspensions, at reference height
Tools.
Compress the suspension, to obtain the values at reference height.
[1]Set of two suspension compressors: 9511T.A
[2] Set of four straps : 9511T.B
[3] Set of four shackles :9511T.C
A > B =
Negative figure: – = TOEOUT
A < B = Positive figure: + = TOEIN
WARNING
B3CP04LC

Downloaded from www.Manualslib.com manuals search engine 383
AXLES
SUSPENSION
STEERING
AXLE GEOMETRYXSARA
Values of the front and rear suspensions, at reference height
Front axle
Adjustable
YES
NO
Pivot angle
Camber CastorTracking
Camber
(*) CRD
= Difficult road conditions.
Tracking
Tolerances
± 30’ ± 30’ ±18’ ± 1 mm 1,5 ± 1 mm
0°15’ ± 10’
(toe-out)
3° 2°55’ 3° ± 07’ 2°55’
10°22’ 11° ± 07’ 10°26’
0°12’ 0° ± 07’ 0°07’ 10°40’
0°
Saloon or
entreprise KFWSaloon all engine
typesexcept KFW
Estate
all engine types
except CRD (*)
Rear axle
NO YES
Saloon CRD (*)
KFW2.0i 16V (RFS)Saloon CRD (*)
all engine types
except KFW
Estate CRD (*)
all engine types
Adjustable TolerancesSaloon all engine types
Saloon entreprise2.0i 16V (RFS)Estate
all engine typesSaloon CRD (*)
all engine types
Estate CRD (*)
all engine types
10°44’
± 1,3 mm
± 15’4,54 ± 1,3 mm 5,1 ± 1,3 mm 4,27 ± 1,3 mm 3,45 ± 1,3 mm
0°41’ ± 11’ 0°46’ ± 11’ 0°39’ ± 11’ 0°31’ ± 10’
0°57’ 0°58’ 0°59’

Downloaded from www.Manualslib.com manuals search engine 384
AXLES
SUSPENSION
STEERING
XSARA
AXLE GEOMETRY
a= Angle which defines the tracking between the front and rear axles.
Its value must not exceed
12'.
B3CP04UC

Downloaded from www.Manualslib.com manuals search engine 385
AXLES
SUSPENSION
STEERING
XSARA
FR ONT AXLE
Tightening torques (m.daN).
(1)
Damper nut: 4,5 ± 0,4
(2)Cup screw : 2,5 ± 0,3
(3)Suspension leg(4)Antiroll bar link rod upper balljoint: 3,7 ± 0,3
(5)Suspension leg pivot (hollow pivot): 4,5 ± 0,5
(5) Suspension leg pivot (pivot «H»): 5,5 ± 0,5
(6)Antiroll bars(7)Antiroll bar link rod lower balljoint:3,7 ± 0,3
(8)Pivot lower balljoint:4 ± 0,4
(9)Driveshaft nut: 32,5 ± 2,5
(10) Wheel bolt:9 ±1
(11)Lower arm front mounting: 7,6 ± 0,7
(12) Lower arm rear mounting
and antiroll bar bearing: 6,8 ± 0,6
(13)Screw under rear mounting: 3,1 ± 0,3
(14) Balljoint fixing on lower arm:5 ±0,5Subframe to bodyshell fixing screw: 8,5 ± 0,8
B3CP040PB3CP041D
VehiclesRPO 8667#are all equipped
as standard with ventilated discs.

Downloaded from www.Manualslib.com manuals search engine 389
AXLES
SUSPENSION
STEERING
XSARA
REAR AXLE
Tightening torques (m.daN).
(1)
Antiroll bar lever: 3,2 ± 0,3
(2)Antiroll bar(3)Transversal torsion bars(4)Rear crossmember flanges: 8,3 ± 0,8
(5) Front silentblocks: 5,5 ± 0,5
(6)Rear silentblocks: 4,5 ± 0,4
(7)Antivibration clamp(8) Damper pin:9,6 ± 0,9
(9)Stub axle nuts (lubricated):18,5 ±1
NOTE:
The RHtorsion bar is identified by 1 paint line.
The
LHtorsion bar is identified by 2 paint lines.
B3DP04SP

Downloaded from www.Manualslib.com manuals search engine 390
AXLES
SUSPENSION
STEERING
REAR AXLE
XSARA
Vehicles
Engines Diameter colour reference Diameter colour referenceTorsion bars (mm) Antiroll bar (mm)
3door Entreprise
19,3 Violet 19 Orange
3 and 5door TT
exc. Entreprise
Estates All types
18,7
20 Grey20 Green
3 and 5door TT19,3
Violet19 Orange
Estates All types20 Grey20 Green
3door VTS
3 and 5door TT
Estates All types21Light green
23
19,3Violet19
20
Grey20Without colour,
or white sticker yellow 18 Blue
1.9 D
1.6i 16V 2.i 16V
1.4 HDi 2.0 HDi
2.0i 16V
Grand Export
«CRD»
Orange
Green

Downloaded from www.Manualslib.com manuals search engine 391
AXLES
SUSPENSION
STEERING
XSARA REAR AXLE
The front silentblocks are aligned at an angle of 45°in relation to the vehicle’s axis.
The rearsilentblocks are in parallel with the vehicle’s axis.
NOTE:There are two suppliers for the silentblocks:

RBT, identified by a Green or Yellow painted dot on the side of the mounting.
PAULSTRA, identified by a Blackpainted dot on the side of the mounting.
It is
FORBIDDENto swap components of different suppliers.
Operating clearance X = 1 to 1.4 mm.
NOTE:
The RH torsion bar can be identified by 1
paint line.
The LH torsion bar can be identified by
2 paint lines.
B3DP04UDB3DP04TC

Downloaded from www.Manualslib.com manuals search engine 392
AXLES
SUSPENSION
STEERING
Adjusting the rear dummy damper
Lengths of the rear dummy damper (mm)
Grand export
346
339
346
342 Normal driving
339
318
336
XSARA REAR DAMPER
E5AP14WC
Engines
1.9 D
1.6i 16V 3door
1.6i 16V 5door
2.0i 16V (RFN) 1.4 HDi
2.0 HDi
2.0i 16V (RFS)
Estates and
Entreprise all types