2004 Citroen XSARA battery

Downloaded from www.Manualslib.com manuals search engine 310
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: MA PILOTED MANUAL GEARBOX
Engaging of «N», using a diagnostic tool.
Preliminary operations:
Battery voltage higher than 12.5 volts.
Ignition switched on.
Connect the diagnostic tool to the vehicle’s diagnostic socket.
From the diagnostic tool menus, select:
«DIAGNOSIS»
MA type piloted manual gearbox.
Actuator test.
Gearbox actuator test.
Gear engagement test.
N(neutral).
NOTE:The letter «N»should appear on the instrument panel.
If not, see the following solution:
Engaging of
«N», without using a diagnostic tool.
Engaging of «N», without using a diagnostic tool.
In this configuration, the gearbox actuator is blocked, gear engaged.
NOTE:This recovery solution is to be used solely in a case where the
attempt to make the gearbox actuator engage b via the diagnostic toolhas failed.
Engines: HFX KFV NFU 8HX
C2

Downloaded from www.Manualslib.com manuals search engine 311
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: MA PILOTED MANUAL GEARBOX
Engines: HFX KFV NFU 8HX
Engaging of «N», without using a diagnostic tool (continued).
Preliminary operation:
Disconnect the battery negative terminal.
Remove the air filter.
Use a
22 mmspanner.
Use the spanner to lift the gear engagement lever the maximum possible until
the axis
«A»of the engagement lever is perpendicular to the axis «B»(mid
point of the gear engagement lever).
When this position is attained, position
«N»is engaged.
B2CP3L8D
C2

Downloaded from www.Manualslib.com manuals search engine 332
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOX
Engines: KFV NFU RFN RHZ
Precautions to be taken.
Towing.
The front of the vehicle must be raised in order to be towed.
If the front of the vehicle cannot be raised:
IMPERATIVE: Put gear lever in position «N».
Do not add any oil.
Do not exceed
30 mphover a distance of 30 milesof maximum.
Driving.
Never drive with the ignition switched off.
Never push the vehicle to try to start it
(impossible with an automatic gearbox).
NOTE:The automatic gearbox is only lubricated when the engine is
running.
Repairs on electrical components.
Do not disconnect:
The battery when the engine is running.
The ECU when the ignition is switched on.
Before reconnecting a switch,check: The condition of the various contacts (for deformation, corrosion etc).
The presence and condition of the mechanical locking.
When performing electrical checks: The battery should be correctly charged.
Never use a voltage source higher than 16V.
Never use a test lamp.
C3 XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 345
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
NOTE:The «shift lock»«P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch. Automatic gearbox ECU.
Electrical harnesses.
Battery voltage.
Remove:
The gear lever knob
(1)(pull upwards).
The cover (2)(Unclip).
The top of the central console (3).
Unlock the «shift lock» (4)with the aid of a screwdriver.
Move the gear selection lever out of position «P».
Engine: KFV
C3
C5FP0ETCB2CP3GZC

Downloaded from www.Manualslib.com manuals search engine 346
CLUTCH
GEARBOX
TRANSMISSION
XSARAAL4 AUTOMATIC GEARBOX
Engines: NFU RFN RHZ
SHIFT LOCK.
NOTE:
The «shift lock»«P».
U
nlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed. Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch.
Automatic gearbox ECU.
Electrical harnesses. Battery voltage.
Remove:
The cover
(1).
Unlock the «shift lock» (2) with the aid of a screwdriver.
Move the gear selection lever out of position «P».
C5FP06ZC
C5FP06YC

Downloaded from www.Manualslib.com manuals search engine 480
ELECTRICAL
SYSTEM
CHARGING CIRCUIT ALTERNATOR WITH MONOFUNCTION REGULATOR
Checking the alternator output.
Connect as shown in the diagram opposite, using an ammeter (A), a voltmeter (V),
and a rheostat
(R)or a Volt/Ammeter/Rheostat combination.
Referring to the vehicle’s equipment specification
(see table opposite), adjust the
engine speed and rheostat charge to obtain
U = 13.5 V.
Reminder:The excitation energising current will flow through the warning lamp;
check that the warning lamp comes on when the ignition is switched on. It shouldgo out when the engine has started
(accelerate slightly).
Checking the voltage regulator.
Set the rheostat to zero and disconnect all the electrical consumers.
Display
3000alternator rpm. If U alternator is > 14.7 V, the regulator is faulty.
Note:These tests should be performed with the engine hot and the battery fully
charged.
Method of reading the alternator speed.
Fit a reflecting shim on the pulley of the alternator.
Adjust a stroboscope to the frequency equivalent to the control speed.
(e.g. 2000 rpm = 2000/60 = 83 Hz).
Adjust the engine speed so that the shim appears fixed.
D1AP025C
A: Ammeter.B:Battery.G: Generator.L: Warning lamp.K1and K2:Switch.R: Electric charge.S:Shunt 200mV/200A.V:Voltmeter.1 : Alternator.