2004 Citroen XSARA PICASSO Tool kit

Downloaded from www.Manualslib.com manuals search engine 259
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Engines: 8HX 8HW
Tools.
[1] Ø 10 mmlow pressure connector: 4215T.
[2]Pressure gauge for testing boost pressure: 4073T.A Tool kit 4073T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel
injection engines.
Link tools [1]and [2]in series between the fuel high pressure pump and the fuel filter.
ESSENTIAL:Check that the tool [2] is clean.
Check the negative pressure according to the table below:
Vacuum Observations
10 ±5 cmHg
Engine driven by the starter motor
20 ±5 cmHg
60 ±5 cmHgEngine running under full load
Supply circuit obstructed
(full tank
strainer, piping, fuel filter).
B1BP2NWC
C2 C3

Downloaded from www.Manualslib.com manuals search engine 260
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Engines: 8HV 8HY 9HZ 9HY
Tools.
[1] Ø 10 mmlow pressure connector: 4215T.
[2]Pressure gauge for testing boost pressure: 4073T.A Tool kit 4073T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel
injection engines.
Remove the air filter duct.
Link tool [1]in series, downstream of the injectors, between the fuel high pressure pump
and the fuel filter at «a»and «b».
WARNING:Any checking of pressure downstream of the fuel filter is prohibited.
Switch on the ignition.
ESSENTIAL: Check that the tool [2] is clean.
Check the negative pressure according to the table below:
VacuumObservations
10 ±05 cmhg
Engine driven by the starter motor
20 ± 20 cmhg
60 ± 05 cmhgEngine running under full load
Supply circuit obstructed
(full tank
strainer, piping, fuel filter).B1BP2PHC
C3 XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 261
INJECTION
XSARA PICASSO
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Engines: RHY RHZ
Tools.
[1] Ø 10 mm
low pressure connector: 4215T.
[2] Ø 8 mmlow pressure connector: 4218 T.
[3]Pressure gauge for testing boost pressure: 4073 T Kit 4073 T
Connect the tool [1]between the booster pump and the fuel filter (white mark at "a" on the
fuel supply pipe).
Connect the tool [2]downstream of the diesel injectors, between the high pressure fuel
pump and the fuel filter (green mark at "b"on the fuel return pipe).
WARNING: Any check of pressure downstream of the fuel filter is PROHIBITED.
Checks on pressure:static.
Switch on ignition
For 3 seconds(normal functioning):
Fuel supply pressure shown by the pressure gauge [3] = 1.8 ± 0.4 Bar. Fuel return pressure shown by the pressure gauge [3] = 0.5 ± 0.4 Bar.
B1BP1TWD

Downloaded from www.Manualslib.com manuals search engine 266
INJECTION
CHECKS: TURBO PRESSURE
Engine: RHZ
XSARA PICASSO
Tools.
[1]
Pressure gauge for checking boost pressure: 4073T.A Kit 4073T
[2]Sleeve for checking boost pressure: 4185T
[3]Adaptor sleeve: 4229T
Checks.
IMPERATIVE: respect the following checking requirements: Engine at running
temperature. Vehicle in running order at full load.
Preparation.
Remove the collar fixing (3).
Insert the tool [2]connected with tool [3], between the pipe (1)and the duct (2).
Position tool [1]in the vehicle.
Connect the sleeve [2]to the tool [1]with its tube «a».Procedure. Start the engine.
Engage first gear and start the engine.
Engage the gears up to third gear.
Decelerate to
1000 rpm.
Accelerate hard, and check the pressure:0.6 ± 0.05 Bar (1500 rpm).
Accelerate freely in kickdown (changing from fourth to third gear).
Check the pressure:0.95 ± 0.05 Bar(between 2500 and 3500 rpm).
Remove the tools, reposition the pipe (1)and refit the collar (3).B1HP12JD

Downloaded from www.Manualslib.com manuals search engine 267
INJECTION
CHECKS: TURBO PRESSURE
Engine: RHY
Tools.
[1]
Pressure gauge for checking boost pressure: 4073T.A Kit 4073T
[2]Sleeve for checking boost pressure: 4185T
Checks.
IMPERATIVE: respect the following checking requirements: Engine at running temperature.
Vehicle running at full load.
Preparation.
Remove the collar (3) and the sleeve.
Insert the tool [2]between the pipe (1)and the duct (2).
Position tool [1]in the vehicle.
Connect the pressure gauge [1]to the tool [2]with its tube «a»long enough for the gauge to
be positioned inside the vehicle.
Procedure. Start the engine.
Engage first gear and start the engine.
Engage the gears up to third gear.
Decelerate to
2000 rpm.
Gradually accelerate.
Check the pressure:
0.95 ± 0.05 Bar Remove the tools, refit the collars (3)and the sleeve.B1BP1ZXD
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 276
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / FILLING OF THE ADDITIVE RESERVOIR
Imperative: Respect the safety and cleanliness requirements.
Tools.
Filling kit comprising the following items:1Container of Eolys2Filters2Tubes1Empty container2Hooks1Adaptor
Filling.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves
that are resistant to hydrocarbons.
Place the vehicle on a lift.
Disconnect the battery negative terminal.
Unclip the the factory filler connector
(1).
Couple the container of additive to the tube (2)using the adaptor and the tube (with tap)from the
filling kit.
Screw the filler connector on the additive container
(3)at «b».
Place the additive container (3)on the component lift.
Open the tap located on the filler connector at «a».
Tilt the additive container (3)(to facilitate the end of filling).
Close the tap at «a».
Remove the filler connector and the tube (4).
Couple the tube (2).
Reconnect the battery negative terminal.
IMPERATIVE: The filling kit should be recycled after this operation. Any «Eolys» additive
containers that have been opened should not be kept.
XSARA PICASSO
B1HP1UVC
C4BP1EGC

Downloaded from www.Manualslib.com manuals search engine 277
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / CHECKING THE ADDITIVE PUMP
Engine: 9 HZ
IMPERATIVE: Respect the safety and cleanliness requirements.
Tools.
[1]
Manual pressure/vacuum pump: FACOM DA 16
[2]Additive container: ().1613.G Kit 1613
Checks.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves that are
resistant to hydrocarbons.
Place the vehicle on a lift.
Raise the vehicle
To test the flow of the additive pump :
Uncouple the tube
(1).
Couple tool [2]on the outlet «a»of the additive reservoir.
Operate for 50 secondsthe actuator test «Additive pump»with the aid of LEXIA or PROXIA.
IMPERATIVE:The volume collected by the tool [2] should be 20 ± 5 ml.
NOTE:
Replace the additive pump if it is defective.
Couple the tube (1).
Operate the actuator test «Filling the tube: additive pump – additive injector», with the aid of LEXIAorPROXIA.
B1HP1UTC
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 354
CLUTCH
GEARBOX
TRANSMISSION
DRIVESHAFTS GEARBOX
Tightening torques (m.daN)
Driveshaft
bearing Engines
V ehiclesGearboxRH side LH side Tool kitGearbox oil seal mandrels
24,5 ± 0,5
32 ± 1,5
32,5 ± 2,57114T.W
Seal extractor
RH / LH
() 0338 C
() 0338 J1
+ () 0338 J3() 0338 H1
+ () 0338 H2
() 0338 J1
+ () 0338 J2() 0338 H1
+ () 0338 H2() 0338 7114T.X
7116T Driveshaft
nut
HFX KFV KFU
8HX 8HW
NFU
KFW NFU
NFV RFS RFN 6FZ WJY
8HZ 9HZ 9HY RHY RHZ
8HV 8HY
NFU RFN RHZ
KFV MA/5
XSARA
XSARA PICASSOC2 C3 C3 Pluriel
XSARANO
2 ± 0,2
1,8 ± 0,1
2 ±0,2
1,8 ±0,1
1 ±0,1
C3
C3
XSARA PICASSO
XSARA
Tightening torque (m.daN) for wheel bolts: XSARA = 8,5 ± 0,8 XSARA PICASSO = 10 ± 1 C2 C3 C3 PLURIEL = 9 ± 1BE4/5
AL 4
C2 C3 C3 PLURIEL XSARA XSARA PICASSO