2004 Citroen C3 steering wheel

Downloaded from www.Manualslib.com manuals search engine ENGINE
201
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1BP304D
Tools.
[1]
Flywheel setting peg: ().0194.C
[2]
Camshaft setting peg:().0194.B
[3]
Crankshaft setting peg: ().0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove: The front RH wheel.
The front RH splashshield.
The accessories drive belt
(see corresponding operation).
Uncouple: The fuel supply unions
(1).
The air/air heat exchanger inlet and outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connecter at
«a».
Remove and move aside the power steering fluid reservoir
(6).
Uncouple, plug and move aside the tube
(2).
Support the engine with a roller jack equipped with a block.
Remove the engine supports
(4)and (5).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 204
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper timing cover
(12).
The lower timing cover (11).
The accessories drive pulley (9).
The screw (10).
Tightening torqueScrew (10)Pretighten to:3 ± 0,3 m.daN.
Angular tighten:180°±5°.
Remove tool [1].
Refit:
The engine support
(8), tighten to 5,5 ± 0,4 m.daN.
The engine support (4), tighten to 6,1 ±0,6 m.daN.
The engine support (5), tighten to 2,5 ±0,2 m.daN.
The electrical harness (7).
The power steering fluid reservoir (6).
XSARA PICASSO
Couple:
The tube (2).
The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
The fuel unions (1).
The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
The accessories drive belt
(see corresponding operation).
The front RH splashshield
(see corresponding operation).
The front RH wheel, tighten to 9 ±1 m.daN.
Reconnect the positive and negative terminals of the battery.
IMPERATIVE:Perform the operations that are necessary following a
reconnection of the battery (see corresponding operation).

Downloaded from www.Manualslib.com manuals search engine 205
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1BP304D
Tools.
[1]
Flywheel setting peg: ().0194.C
[2]
Camshaft setting peg:().0194.B
[3]
Crankshaft setting peg: ().0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove: The front RH wheel.
The front RH splashshield.
The accessories drive belt
(see corresponding operation).
Uncouple:
The fuel supply unions
(1).
The air/air heat exchanger inlet and outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connecter at
«a».
Remove and move aside the power steering fluid reservoir
(6).
Uncouple, plug and move aside the tube
(2).
Support the engine with a roller jack equipped with a block.Remove the engine supports
(4)and (5).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 210
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting (continued).
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper timing cover
(12).
The lower timing cover (11).
The accessories drive pulley (9).
The screw (10).
Tightening torqueScrew (10)Pretighten to:3 ± 0,3 m.daN.
Angular tighten:180°±5°.
Remove tool [1].
Refit:
The engine support
(8), tighten to5,5 ± 0,4 m.daN.
The engine support (4), tighten to 6,1 ±0,6 m.daN.
The engine support (5), tighten to 2,5 ±0,2 m.daN.
The electrical harness (7).
The power steering fluid reservoir (6).
XSARA PICASSO
Disengage the jack from under the engine.
Couple:
The tube
(2).
The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
The fuel unions (1).
The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
The accessories drive belt
(see corresponding operation).
The front RH splashshield (see corresponding operation).
The front RH wheel, tighten to 9 ± 1 m.daN.
Reconnect the positive and negative terminals of the battery.
IMPERATIVE: Perform the operations that are necessary following a
reconnection of the battery (see corresponding operation).

Downloaded from www.Manualslib.com manuals search engine 220
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Remove:
The fixings of the pipe linking the power steering pump with the rotary valve.
The clutch lower closing plate.
Lock the engine flywheel, using tool
[6].
Remove the screw (8).
Refit the screw (8)without its thrust washer.
Remove:
The accessories pulley
(9), using tool[8].
Tool [6].
The lower torque reaction rod.
Support the engine by means of a workshop hoist.
Remove:
The bearing shell fitting
(10).
The nut (12).
Screws (11).
The bracket (13).
NOTE:Lift then lower the engine with the workshop hoist, to have access to the
timing cover fixing screws.
Remove:
The intermediate timing cover.
The lower timing cover.
B1CP04BCB1BP2R3CB1BP2R4C
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
355
C2 AXLE GEOMETRY
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point (see corresponding operation).
Conditions for checking and adjusting
Vehicle heights at reference height
E1APOBZD
Front height Rear height
L1L2
H1 = R1 – L1 H2 = R2 + L2
H1
= Measurement between the measuring zone underneath the front H2 = Measurement between the measuring zone underneath the rear
subframe and the ground. sill and the ground.
R1= Front wheel radius under load.R2= Rear wheel radius under load.L1= Distance between the wheel axis and the measuring zoneL2= Distance between the wheel axis and the measuring zone
underneath the front subframe. underneath the rear sill.

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
356
C2 AXLE GEOMETRY
B3CP07SD
Measuring front height Measuring rear height
[1]
Gauge for measuring the wheel radius, 4 bolts, tool 8006T
Z1
= Measuring zone underneath the front subframe.Z2= Measuring zone underneath the rear sill.
Measure the radius of the front wheel
R1 Calculate dimension H1 = R1 – L1Measure the radius of the rear wheel R2 Calculate dimension H2 = R2 + L2
Value at referenceExcept CRD (*)Value at referenceExcept CRD (*)heightHFX KFV 8HX NFUheightHFX KFV 8HX NFU
(+ 6 8 mm)L1 = 142,5 mmL1 = 152,5 mm(+ 10 6 mm)L2 = 52 mm L2 = 42 mm
Compress the suspension to obtain the calculated values.
The height difference between the two axle dimensions should be less than 10 mm.(*) = CRD: Difficult road conditions.

Downloaded from www.Manualslib.com manuals search engine 357
AXLES
SUSPENSION
STEERING
A < B = Positive figure: + = TOEIN
A > B = Negative figure: = TOEOUT
WARNING
AXLE GEOMETRY
Rear axle Front axle
Dissymmetry of lower camb8er 0° 18. Dissymmetry of lower castor at
0° 30’.
DISSYMMETRY OF LOWER CAMBER 0° 18’.
Distribute symmetrically, LH / RH wheel, the total tracking value.
All types (except CRD)
NFU
Vehicle TrackingCastor Camber Pivot angle
(± 0°18’) (± 0°30’) ± 0°30’
ADJUSTABLE Non adjustable
2 ± 1
0°18’±0°09’ 3°58’ 0°31’ 11°26’
NFU
Vehicle TrackingCastor Camber Pivot angle
±0°30’
ADJUSTABLENon adjustable
2 ± 1
0°18’± 0°09’ 4° 0°32’ 11°35’Tracking Camber
Non adjustable
5,5 ± 1
0°53’ ± 0°09’ 1°30’
TrackingCamber
Non adjustable
5,8 ±1
0°49’ ± 0°09’ 1°31’
All
Typesmm
0°
All
Typesmm
0°
B3CP02UC
C2
± 0°18’ ± 0°30’
HFX KFV 8HX HFX KFV 8HX