2004 Citroen C3 too low

Downloaded from www.Manualslib.com manuals search engine 335
CLUTCH
GEARBOX
TRANSMISSION
Engines: KFV NFU RFN RHZ
Updating the value of the oil usage counter.
Using PROXIA.
Access to reading and recording of the oil counter is via the menu:
«Configuration
(integrated circuit button)/ Oil counter».
Adjustment of the oil counter value is done in incremental steps of
2750units.
Using LEXIA or ELIT.Access to reading and recording of the oil counter is via the menu:
«Oil counter».
Adjustment of the oil counter value is done by entering directly the
5 figures of the oil counter.
Downloading.
ECU downloading procedure:
Follow the diagnostic tool procedure.
A new ECU or downloaded update is always configured with the
following options:
SHIFT LOCK gear selection lever position.
Without OBD outlet
(depollution L4).
If the ECU is to be fitted to a vehicle with depollution
L4or not
equipped with gear lever locking safety: Perform a configuration operation.
Pedal initialisation.
A pedal initialisation must be carried out in the following cases:
Replacement of the automatic gearbox ECU.
Replacement of the automatic gearbox.
Downloading of the ECU configuration.
Adjustment or replacement of the accelerator cable.
Replacement of the butterfly potentiometer.
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOXC3 XSARA XSARA PICASSO
Procedure for initialising the automatic gearbox ECU

Downloaded from www.Manualslib.com manuals search engine 351
CLUTCH
GEARBOX
TRANSMISSION
DRAINING / FILLING / TOPUP: AL4 GEARBOX
Tools.
[1]
Filling cylinder: ().0341
Draining.
IMPERATIVE:
The gearbox should be drained when the oil is warm (at least 60°C), to
eliminate the impurities in suspension in the oil.
NOTE:Draining is partial, the converter cannot be completely emptied.
Remove the drain plug
(1).
NOTE:Approx. 3 litres of oil should flow out.
Filling.
Refit the drain plug (1)(equipped with a new seal), tighten to2,4 ±0,2 m.daN.
Remove the oil filler cap (2).
Use tool [1].
Oil capacity for dry gearbox:

EW engine:5,85 litres.
DWengine:5,40 litres.
Oil remaining after draining:
3 litres(approx.).Quantity of oil to be put in :3 litres(approx.).Refit the oil filler cap (2)(equipped with a new seal), tighten to 2,4± 0,2 m.daN.
Initialise the oil wear counter (follow the diagnostic tool procedure).
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3AYD
B2CP31GC

Downloaded from www.Manualslib.com manuals search engine 353
CLUTCH
GEARBOX
TRANSMISSION
DRAINING / FILLING / TOPUP: AL4 GEARBOX
Thread of oil then "dripdrip".
Refit the plug (3), Tighten to 2,4± 0,2 m.daN.
"Dripdrip" or nothing.
Refit the oil level plug (3).
Stop the engine.Add
0.5 litresextra oil into the gearbox.
Repeat the oil level procedure.
NOTE:The level is correct at the moment the thread of oil becomes “dripdrip”.
Refit the oil level plug
(3)(equipped with a new seal), tighten to2,4±0,2 m.daN.
Checking the oil level (continued).
Refit the oil filler plug (3) (equipped with a new seal), tighten to 2,4± 0,2 m.daN.
An excessive level of oil can lead to the following consequences:
Oil heating up abnormally,
Oil leaks.
A level that is too low will result in the destruction of the gearbox.
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3AZD

Downloaded from www.Manualslib.com manuals search engine 423
BRAKES
B3FP160C
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
With the bleeding apparatus.
Connect the bleeding apparatus [1]on the brake fluid reservoir (1).
Adjust the apparatus pressure to
2 Bars.
For each circuit:
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles. Close the bleed screw.
Remove the bleeding apparatus
[1].
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE:Two operators are necessary.
For each circuit:
Apply the brake pedal to place the circuit under pressure.
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw. Remove the tool
[1].
NOTE:Recommence the process a second time if that is necessary.
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
C2

Downloaded from www.Manualslib.com manuals search engine 438
BRAKES
B3FP160C
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
With the bleeding apparatus.
Connect the bleeding apparatus [1]on the brake fluid reservoir (1).
Adjust the apparatus pressure to
2 Bars.
For each circuit:
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw.
Remove the bleeding apparatus
[1].
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE:Two operators are necessary.
For each circuit:
Apply the brake pedal to place the circuit under pressure.
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container. Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw.
Remove the tool
[1].
NOTE:Recommence the process a second time if that is necessary.
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 458
BRAKESBLEEDING THE BRAKESXSARA PICASSO
Tools.Bleeding equipment of type «LURO» or similar.IMPERATIVE: For bleeding the secondary circuit, use ELIT, LEXIA or PROXIA diagnostic tools.
Draining.
Drain the brake fluid reservoir as empty as possible using a syringe.
Disconnect the brake fluid warning lamp connector.Retrieve the brake fluid reservoir from its supply pipes by pulling upwards.
Finish emptying the reservoir of brake fluid.
Clean the brake fluid reservoir.
Refit the brake fluid reservoir.
Reconnect the brake fluid warning lamp connector.
Filling.Refill the reservoir with brake fluid.WARNING:Use only the recommended hydraulic fluids.
Bleeding.
NOTE:Two technicians are required.
IMPERATIVE:During bleed operations, ensure that the level of brake fluid is maintained in the
reservoir and top it up, use only new brake fluid.
Bleed each wheel cylinder, proceeding in the following order:
Rear right hand wheel.
Front left hand wheel.
Rear left hand wheel.
Front right hand wheel.

Downloaded from www.Manualslib.com manuals search engine 500
26 ± 2 23,2 ± 2 21 ± 2 19,2 ± 2 15,3 ± 2 15 ± 2
4,3 ±2 3,4 ± 2 3,1 ± 2 2,8 ± 2 2,7 ± 2
25,2 ±223,6 ± 2 21,4 ± 2 20 ± 2 17,6 ± 2 14,5 ± 2
3,5 ± 2 3 ± 2 2,8 ± 2 2,5 ± 2 2,4 ± 2
26,2 ± 2 23,2 ± 2 21 ± 2 19,2 ± 2 15,3 ± 2 15 ± 2
4,3 ± 2 3,4 ± 2 3,1 ± 2 2,8 ± 2 2,7 ± 2
CHECKING THE EFFICIENCY OF THE AIR CONDITIONING SYSTEM
Checking pressures
Tools. 1
charging station. 2thermometers.
Once the preliminary conditions, vehicle equipment and checks havebeen fulfilled
(see table). After the air conditioning has been on for
three minutes, record the following parameters: The temperature of the air coming from the central vents
(see table).
The High Pressure. The Low Pressure.
Compare the values recorded with the table below, or the graphs.
Ambient temperature in °C40 35 30 25 20 15
VehiclesEngines
C3
C3
C3 PlurielKFV
NFUHigh pressure (Bars)
Low pressure (Bars)
Low pressure (Bars)
High pressure (Bars)
Low pressure (Bars)8HX 8HWVehicle using R134.a fluid
(Compressor with variable capacity)
High pressure (Bars)
AIRCONAIRCON
C3 C3 PLURIEL XSARA XSARA PICASSO KFV

Downloaded from www.Manualslib.com manuals search engine 501
AIRCON
23 ± 2 22,5 ± 2 20 ± 2 17 ± 2 15,5 ± 2 14,5 ± 2
3,8 ± 0,2 3,6 ± 0,2 3,5 ± 0,2 3,1 ± 0,2 3 ± 0,2 2,9 ± 0,2
24,5 ±221,5 ±2 18,5 ± 2 17 ± 2 15,5 ± 2
4 ±0,2 3,8 ± 0,2 3,5 ± 0,2 3,2 ± 0,2 3 ± 0,2
21,5 ± 2 22,5 ± 2 20 ± 2 18 ± 2 16,5 ± 2 15,6 ± 2
3,2 ±0,23,3 ±0,23 ±0,22,8 ± 0,2 2,6 ± 0,2
25,5 ±320,5 ±318 ± 3 20 ± 3 13,5 ± 3 11 ± 3
4 ±0,33,5 ± 0,3 3 ± 0,3
25 ± 3 22,5 ± 3 20 ± 3 17 ± 3 15 ± 3
4 ±0,33,5 ± 0,3 3 ± 0,3
CHECKING THE EFFICIENCY OF THE AIR CONDITIONING SYSTEM
Checking pressures
Tools. 1
charging station. 2thermometers.
Once the preliminary conditions, vehicle equipment and checks havebeen fulfilled
(see table). After the air conditioning has been on for
three minutes, record the following parameters: The temperature of the air coming from the central vents
(see table).
The High Pressure. The Low Pressure.
Compare the values recorded with the table below, or the graphs.
Ambient temperature in °C40 35 30 25 20 15
VehiclesEngines
XSARA
XSARA
PICASSOTU
EW
High pressure (Bars)
Low pressure (Bars)
Low pressure (Bars)
High pressure (Bars)
Low pressure (Bars)DWVehicle using R134.a fluid
(Compressor with variable capacity)
High pressure (Bars)
XSARA XSARA PICASSO
High pressure (Bars)
Low pressure (Bars)
High pressure (Bars)
Low pressure (Bars)
TU
EW
DW