2004 Citroen C3 injection pump

Downloaded from www.Manualslib.com manuals search engine 262
INJECTION
XSARA PICASSO CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Engines: RHY RHZ (continued)
Checks on pressure: dynamic.Engine running, at idle (normal functioning):
Fuel supply pressure shown by the pressure gauge [3] = 2 ± 0.4 Bar. Fuel return pressure shown by the pressure gauge [3] = 0.7 ± 0.4 Bar.
Abnormal functioning
Impossible to start the engine:
Fuel supply pressure less than 0.8 Bar:
Check the low pressure regulator incorporated in the filter (locked open). Check the high pressure pump distribution valve (locked shut).
Check: diesel injector return flow.(Table below)
Uncouple the diesel injector return pipe.
Fuel supply pressure Fuel return pressure Checks
Between 3and 3.5 Bar 0,7 ± 0,2 BarCheck the condition of the diesel filter
More than
3.5 Bar
More than 3.5 Bar
Less than 0.7 Bar
More than 0.7 Bar
Check the low pressure regulator incorporated in
the filter (locked shut): replace.
Check the fuel return circuit
(pipe pinched or trapped…)
Between 0.8 and 1.5 BarLess than 0.7 BarCheck the fuel suppy circuit:
Booster pump (low pressure), piping.
Check:
Observe:
The flow should be drop by drop.
Diesel injector functioning correctly.
Excessive fuel return.
Diesel injector locked shut.

Downloaded from www.Manualslib.com manuals search engine 268
INJECTION
CHECKING THE AIR SUPPLY CIRCUIT
Tools.
[1]
Manual pressurevacuum pump: FACOM DA 16
Vacuum pump:
Connect the tool [1]onto the vacuum pump (1).
Start the engine.
Wait 30 seconds.
The vacuum value should be
0.9 ±0.1 barat idle.
B1HP1K8D
Engines: 8HX 8HW 8HY 8HV
C2 C3

Downloaded from www.Manualslib.com manuals search engine 269
INJECTION
CHECKING THE AIR SUPPLY CIRCUIT
Engines: RHY RHZ
XSARA PICASSO
Tools.
[1]Manual vacuum pump : FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
Vacuum pump.
Connect the tool [1]on the vacuum pump (1).
Start the engine.
Pressure should be
0.8 barat 780 rpm.Boost pressure regulator electrovalve. Connect the tool [1]between the electrovalve (2)and the valve (3)of the boost pressure
regulator.
Compare readings with the values in the table below.
Pressure regulator valve. Connect the tool [1]on the valve (3).
Appy a pressure of 0.5 barto activate the rod "a":
Rod "a"should be moved 12 mm.
Engine speed (rpm) Pressure (Bar)
780 0,6
4000 0,25
B1HP12FD

Downloaded from www.Manualslib.com manuals search engine 270
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: 8HX 8HW
Engines: 8HV 8HY
Tools.
[1]
Manual pressurevacuum pump: FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel
injection (HDi) engines.
EGR v
alve.Connect tool [1]on the capsule takeoff (2).
Apply a vacuum of approx.0,6 barseveral times to activate the rod «a».
In abruptly suppressing the vacuum, the valve should click and lock itself back on its seating.
Regulation electrovalve (EGR).(Engine:8HX8HW).Check to be performed between the electrovalve (1)and the EGR valve (2).
Link the tool [1]in series, between the electrovalve (1)and the capsule (2).
Compare the values noted with those in the table below.
Regulation electrovalve (EGR).(Engine:8HV8HY).Check to be performed between the electrovalve (2)and the EGR valve (1).
Link the tool [1] in series, between the electrovalve (2)and the capsule (1).
Compare the values noted with those in the table below.
Engine speed (rpm) Vacuum value
780 0,5
2500 0
B1HP15GD
B1HP1K6D
C2 C3

Downloaded from www.Manualslib.com manuals search engine 272
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: RHY RHZ
XSARA PICASSO
Tools.
[1]
Manual vacuum pump : FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
EGR valve.
Connect the tool [1]to the capsule union (1).
Apply several times in succession a vacuum of approx.0.6 barto activate the rod "a".
In abrupt reaction to the vacuum, the valve should close on its seating with a clicking
noise.
Exhaust gas reycling (EGR) electrovalve. Check, not under load, between the electrovalve (2)and the EGR valve (1).
Connect the tool [1]between the electrovalve (2)and the capsule (1).
Compare readings with the values in the table below.
Engine speed (rpm) Vacuum value
7800,5
25000
B1HP12GD

Downloaded from www.Manualslib.com manuals search engine 274
INJECTION
PARTICLE FILTER SAFETY AND CLEANLINESS REQUIREMENTS
Operations on the fuel additive circuit.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves that are resistant to hydrocarbons.
The work area must be ventilated.
In the event of any significant dispersion of additive:
Wear a breathing mask for filtering the particles.
Recover as much of the product as possible.
Place the product thus recovered in an appropriately labelled container. Wash the soiled area with copious amounts of water.
Dispose of materials and solid residues in an authorised recovery point.
IMPERATIVE:The filling kit should be recycled following a repair. All «Eolys» additive containers that have been opened should be
disposed of.
Cleanliness rules.
ESSENTIAL: The operator should wear clean overalls.
Before working on the injection circuit, it may be necessary to clean the unions of the following sensitive components(see corresponding operations).
Fuel filter.
Fuel high pressure pump.
Fuel high pressure regulator.
Fuel high pressure common injection rail. Fuel high pressure piping. Diesel injector carriers.
IMPERATIVE: After dismantling, immediately blank the unions of the sensitive components with plugs, to prevent any ingress of impurities.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 277
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / CHECKING THE ADDITIVE PUMP
Engine: 9 HZ
IMPERATIVE: Respect the safety and cleanliness requirements.
Tools.
[1]
Manual pressure/vacuum pump: FACOM DA 16
[2]Additive container: ().1613.G Kit 1613
Checks.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves that are
resistant to hydrocarbons.
Place the vehicle on a lift.
Raise the vehicle
To test the flow of the additive pump :
Uncouple the tube
(1).
Couple tool [2]on the outlet «a»of the additive reservoir.
Operate for 50 secondsthe actuator test «Additive pump»with the aid of LEXIA or PROXIA.
IMPERATIVE:The volume collected by the tool [2] should be 20 ± 5 ml.
NOTE:
Replace the additive pump if it is defective.
Couple the tube (1).
Operate the actuator test «Filling the tube: additive pump – additive injector», with the aid of LEXIAorPROXIA.
B1HP1UTC
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 278
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / CHECKING THE ADDITIVE PUMP
Sealing of the additive injector.
Couple tool [1] to the tube (1).
Action the manual pump [1].
WARNING:The additive injector should open at a pressure of 100 ± 20 Bars.
Action the manual pump in vacuum
[1]at 800 m.bars.
WARNING:The downstream pressure should not fall rapidly.
NOTE:Replace the fuel tank if the injector is defective.
Couple the tube
(1).
Operate the actuator test «Filling the tube: additive pump – additive injector», with the aid ofLEXIAor PROXIA.
Check the additive level.
The checking of the additive level is done with reference to the gradations «a»marked on the additive
reservoir.
The top graduation indicates maximum filling
(3 Litres).
The difference between the two gradations equates to 0,25 Litres.
XSARA PICASSO
B1HP1UUC
B1KP019C