2004 Citroen C3 cooling

Downloaded from www.Manualslib.com manuals search engine 231
ENGINE
ALL TYPES FILLING AND BLEEDING THE COOLING CIRCUIT
Tools.
[1]
Filling cylinder: 4520T
[2]Adaptor for filling cylinder: 4222T
IMPERATIVE: Respect the safety and cleanliness requirements.
The draining and refilling operations can be carried out using WINN’S or similar coolant fluid replacement
equipment;it is essential to follow the instructions as stated for that equipment.
Filling and bleeding.
Fit the cylinder adaptor [2] 4222T (Picasso,C2,C3)and the filling cylinder [1] 4520T (all types).
Use the coolant to ensure protection between 15°C and 37°C.
Slowly fill the system.
NOTE:Keep the cylinder filled up (visible level).
Close each bleed screw as soon as the coolant flows without air bubbles.
Start the engine :Engine speed
1500 rpm.
Maintain this speed until the first cooling cycle (cooling fans cut in and cut out).
Stop the engine and allow it to cool down.
Remove the filling cylinder
[1] 4520T (all types)and the cylinder adaptor [2] 4222T.
Top up the system to the max. mark, with the engine cold.
Refit the filler cap.
E5AP1GNCB1GP00AC

Downloaded from www.Manualslib.com manuals search engine 255
INJECTION
ADJUSTING THE MECHANICAL CONTROLS OF THE DELPHI INJECTION PUMP
Engine: WJY
Adjusting the fast idle.
Engine cold.
Ensure that the lever (2)is up against its stop to the right.
If not, adjust the tension of the cable (3)using the cable clamp (1).
Finish tensioning using the sleeve tensioner (4).
Engine hot. Check that the cable (3)is in tension.
Checking the thermostatic sensor. There should be a minimum 6 mmcable travel between a cold and a hot engine.
Adjusting the accelerator control.
Prior conditions.
Engine hot (cooling fan is engaged twice).
Checking the accelerator cable tension. Fully depress the accelerator pedal.
Check that the lever (6)is against its stop (5)otherwise, alter the position of the pin.
If not, adjust the position of the accelerator cable tensioning retaining pin.
Ensure that in the idle position the lever
(6)is against the stop (7).
B1HP0K9C
XSARA

Downloaded from www.Manualslib.com manuals search engine 275
INJECTION
SPECIAL FEATURES: FORCED REGENERATION OF THE PARTICLE FILTER
Tools.
Diagnostic stations: LEXIA or PROXIA
Imperative: Respect the safety and cleanliness requirements.
Forced regeneration of the particle filter.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
ESSENTIAL: Connect the vehicle to a gas extractor approved for this type of operation.In the absence of the required installations,carry out the forced regeneration of the particle filter outside the workshop, in a concreted
area well away from any inflammable materials. Place the vehicle in the high position.
WARNING:
Check that the fuel level is sufficient (at least 20 litres).
Start the engine and allow it to warm up (60°C minimum).
Connect the diagnostic tool to the vehicle’s central socket.
Trigger the regeneration cycle, with the diagnostic tool.
Automatic running of the regeneration cycle of the particle filter:
Autocheck by the engine ECU. Stabilisation of engine speed at
4000 rpm, operating with post injection.
Change to idling speed (for 30 seconds).
Stabilisation of engine speed at 3000 rpm, checking of the efficiency of the regeneration of the particle filter.
Change to idling speed.
NOTE:Let the engine run at idling speed for the benefit of cooling.
Stop the engine.
IMPERATIVE: Wait for at least an hour before any operation on the exhaust line.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 494
AIRCONAIRCON
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Changing the filtering/drying cartridge
Tools.
[1]
Charge station :(according to workshop equipment)[2]TORX adaptor: TORX 70 FACOM
Removing.
Depressurise the aircon circuit, using tool [1].
Uncouple the hose
(2).
Remove:
The air filter assembly
(3).
The nuts (1).
Protect the radiator harness with strong cardboard cut to the dimensions of the radiator.
Move aside the cooling fan.
Remove:
The screws
(4).
The brackets (5).
B1BP23FCB1BP23GC
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 498
AIRCONAIRCON
AIR CONDITIONING SYSTEM R 134.a
Testing procedure
Conditions inside the vehicle.
Positions of the air conditioning controls:
Maximum cold.
Maximum blower power.
Air distribution on
«ventilation»with the air vents open.
Position the air inlet flap to outside air.
WARNING:For RFTA (1), disconnect the air inlet motor connector, first
ensuring that it is in the outside air position.
(1) RFTA= Fully automatic air conditioning.
Test procedure.When all these conditions are met, proceed in the following order:
Measure the temperature in the workshop approx. one metre in front of
the vehicle’s air inlet grille.
Start the engine
(without the air conditioning, or the blower, operating)and wait for the cooling fan slow speed to trigger (should the engine tem
perature not rise sufficiently, it is permissable to increase the engine
speed to 2000 rpm)
.
Once it is sufficiently hot in the engine compartment, return the engine
to idle and commence the test.Switch on the air conditioning and adjust the engine speed to
2500 rpm.
In an ambient temperature of 40°C, the engine speed will be brought
down to 2000 rpm, in order for the pressure safety threshold to cut off the
compressor.
For further temperatures/pressures: see Tables and Graphs on following
pages
221, 222 and 226.
After
3 minutesof operation, note down the following 3 parameters:
The temperature of the blown air coming out of the 2 central air vents
(take the average).
The high pressure, via the intermediary of the clickfit union (at the
pressure reducer inlet).
The low pressure, via the intermediary of the clickfit union (at the pressure
reducer outlet).NOTE:The low and high pressures are absolute pressures.
When measuring the blown air temperatures, avoid any contact between
the thermocouple and the air vents.
At the conclusion of the test involving vehicles with
«RFTA»
ALL TYPES