2004 Citroen C3 Steering pivot

Downloaded from www.Manualslib.com manuals search engine 402
AXLES
SUSPENSION
STEERING
A > B =Negative figure: – = TOEOUT
A < B = Positive figure:+ =TOEIN
WARNING
AXLE GEOMETRY
Checks at reference height (the reference height of the vehicle is set as per the table below).
NO CRD Vehicle (CRD = Difficult road conditions)
Front axle Rear axle
Vehicle Tracking Castor Pivot angle Camber Tracking Camber
Adjustable Yes No
All types0 ± 1 mm4,8 ± 1,3 mm
0°09’ at + 0°09’3° ± 18’ 10°43’ ± 30’ 0° ± 30’
0°43’ ± 0°12’ 1°13’ ± 18’
XSARA PICASSO
B3CP02UC

Downloaded from www.Manualslib.com manuals search engine 404
AXLES
SUSPENSION
STEERING
A > B =Negative figure: – = TOEOUT
A < B = Positive figure:+ =TOEIN
WARNING
AXLE GEOMETRY
Checks at reference height (the reference height of the vehicle is set as per the table below).
CRD Vehicle (CRD = Difficult road conditions)
Front axle Rear axle
Vehicle Tracking Castor Pivot angle Camber Tracking Camber
Adjustable Yes No
All types 1 ± 1 mm3,7 ± 1,3 mm
0°18’ at 0°0’2°56’ ± 18’ 10°25’ ± 30’ 0°07’ ± 30’
0°33’ ± 0°12’ 1°14’ ± 18’
XSARA PICASSO
B3CP02UC
Engines: NFV RFN RHY

Downloaded from www.Manualslib.com manuals search engine 405
AXLES
SUSPENSION
STEERING
FRONT AXLE
Tightening torques m.daN.
(1)Damper nut: 4.5 ± 0.4
(2)Cup screw: 2.5 ± 0.2
(3)Suspension leg(4)Antiroll bar link rod balljoint: 3.7 ± 0.3
(5)Suspension leg swivel: 4.5 ± 0.4
(6) Antiroll bar(7)Antiroll bar link rod balljoint: 3.7 ± 0.3
(8)Lower swivel balljoint: 4 ± 0.4.
(9) Hub nut (greased): 32.5 ± 2
(10)Wheel bolt (face and threads not greased):9 ±1
(11) Lower arm front pivot: 7.6 ± 0.7
(12)Lower arm rear pivot and
antiroll bar bearing:6.8 ±0.6
(13) Screw under rear pivot : 3.5 ± 0.3 Lower arm in forged steel : 3.7 ± 0,3 Lower arm in plate steel: 3.1 ± 0,3Screw fixing subframe on bodyshell:8.5 ±0,8Screw fixing balljoint on lower arm (plate steel):4.5 ± 0,4
Antiroll bar
Engine
All TypesDiameter
21colour reference
WHITE Suspension leg angle :
Tab «a»towards the front.B3CP056P
B3CP057D
B3CP043D
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 408
AXLES
SUSPENSION
STEERING
STEERING COLUMN SPECIFICATIONS
Tightening torques (m.daN).
(7)
Pivot balljoint nut: 4 ± 0.4
(8)
Steering rod adjusting lock nut: 4.5 ± 0.4
(9)
Balljoint on steering rack: 6 ± 0.6
(10)
Fixing steering on subframe: 8 ± 0.8
(11)
Hydraulic pipe connection: 2.4 ± 0.2
(12)
Power steering valve: 1.2 ± 0.2
(13)
Plunger flange screws: 1.2 ± 0.2
(14)
Steering ram screw on housing:9 ±1
(15)
Steering ram screw on yoke:9 ±1
NOTE:
When removing the steering, it is imperative to replace screws
(14)and (15)(new screws).
B3EP117D
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 409
AXLES
SUSPENSION
STEERING
Steering Rack pinion Number of teeth Number of steering Turning circle Turning circle
rack travel in rack wheel turns between walls between kerbs
Left hand drive
71,7 x 2
LH helix28 Teeth 3,22 12 m 11,48 m
Right hand driveRH helix
Engines Steering valve
NFV 6FZ RFN RHY
number of teeth :7
Length of the steering link rods (preadjustment):
Between balljoint centres =
392 mm.
Between the centre of the pivot balljoint and the contact face of the steering rack balljoint =
412 mm.
STEERING COLUMN SPECIFICATIONSXSARA PICASSO