2004 Citroen C3 Flywheel

Downloaded from www.Manualslib.com manuals search engine ENGINE
165
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Tools.
[1]
Flywheel peg :4507T
[2]Camshaft peg: 4533TA.C1
[3]Crankshaft setting peg: ().0194.A
Checks.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.Remove:
The oil filter. The engine cover.
The upper timing cover
(1).
The sparking plugs, to ease rotation of the engine.
Rotate the engine by means of the crankshaft screw
(never turn the engine backwards).
B1BP2ZJD
C3

Downloaded from www.Manualslib.com manuals search engine 166
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
B1BP2MBC
Position the tools [3]and [2].
Peg the flywheel, using tool
[1].
NOTE:If the setting is not correct, recommence the operation.
Remove the pegs
[2]and [3].
Refit :
The oil filter.
The timing cover
(1).
The engine cover.
Reconnect the battery.
Lower the vehicle.
Perform the operations that are necessary following a reconnection of the battery.
B1BP2ZTC
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
167
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Tools.
[1]
Flywheel setting peg: 4507T
[2]Engine support crossmember:
[3]Crankshaft setting peg: ().0194.A
[4]Camshaft peg: 4533TA.C1
[5]Belt retaining pin: 4533T.AD
Removing.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.Remove:
The front RH wheel.
The front RH splashshield. The engine cover.
The accessories drive belt
(see corresponding operation).
The crankshaft pulley. The oil filter.
Remove the upper timing cover
(1).
B1BP2ZJD
C3

Downloaded from www.Manualslib.com manuals search engine 168
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
B1BP2ZTC
Rotate the engine by means of the crankshaft pinion screw (2)(clockwise), to bring it to the pegging position.
Peg the flywheel, using tool
[1].
Position the tools
[3]and [4].
Position the tool
[2].
Support the engine.
Remove the screws
(3).
The upper RH engine support.
B1BP2MCCB1BP2MBCB1BP2ZUC
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
171
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ RFN 2003 # NEW ASSEMBLY2003 #
(6)Crankshaft pinion
(7)Accessories drive pulley
(8)Washer
(9)Screw
The pinion
(6)is fitted as an idler on the crankshaft.
The accessories drive pulley
(7)is immobilised on the crankshaft by a halfmoon keyway and
by the tightening of washer
(8)and screw (9).
A:Pegging on manual gearbox.
B:Pegging on automatic gearbox.
The pegging of the crankshaft is done on the flywheel, or on the converter drive plate
(automatic gearbox).
The pegging hole on the cylinder block
(exhaust end)is calibrated and reinforced.
IMPERATIVE: Never turn the crankshaft with the accessories drive pulley slackened.
IMPERATIVE: Never remove the accessories drive pulley without pegging the crank
shaft and the camshafts.
IMPERATIVE: Always turn the crankshaft in the direction of engine rotation.
B1EP1B9D
B1BP2V2D
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine ENGINE
179
CHECKING AND SETTING THE VALVE TIMING
Engine: RFS
Tools.
[1]
Belt tension measuring instrument: 4122T
[2]Camshaft pulley locating peg: 9041T.Z Tool kit 7004T
[3]Crankshaft locating peg: 7014T.N
[4]Camshaft pulley locking peg: 4200T.G
[5]Tensioner spanner: 7017T.W
[6]Toothed sector for locking the flywheel: 9044T
Checking the setting.
Turn the engine by the crankshaft screw (1).
Peg the crankshaft using the tool[3].
ESSENTIAL: Check that the crankshaft DAMPERS pulley is in good condition. If the hub/pulley markings
do not line up, the crankshaft pulley must be replaced.
Peg the camshaft using the tool [2](the locating pegs [2]should slide in easily).
If this is not the case, set the timing.
NOTE:Camshaft hubs (see pages 138and 139).
B1EP12GCB1EP12FC
XSARA

Downloaded from www.Manualslib.com manuals search engine 180
ENGINEXSARACHECKING AND SETTING THE VALVE TIMING
Engine: RFS
Remove:
The peg [3].
The screw (4)(brush the screw thread).
The pulley (5).
The lower cover (6).
Remove:
The tool
[6].
The studs (8).
Fit the tool [4].
Loosen the screws (10).
Remove the tool [4].
Slacken the tensioner roller (7).
Remove the belt (9). Peg the crankshaft using tool
[3].
Peg the camshaft pulleys using tool [2].
Lock the flywheel using the tool [6].
Refit:
The pulley (5).
The screw (4)(tighten moderately).
The peg [3].
B1EP120CB1EP11ZC
Setting the valve timing.

Downloaded from www.Manualslib.com manuals search engine 184
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HX 8HW 8HZ
B1BP2LXC
Tools.
[1]
Pliers for removing plastic pegs : 7504T
[2]Lever for detensioning the dynamic tensioner roller: ().0194.E
[3]Engine flywheel setting peg: ().0194.C
[4]Camshaft setting peg: ().0194.B
[5]Crankshaft and high pressure pump setting peg: ().0194.A
Preliminar
y operations.Remove:
The front RH wheel.
The front RH splashshield, using tool
[1].
The clips of the electrical harness on the upper timing cover. The accessories belt, using tool
[2](see corresponding operation).
Check ing the setting.
Disconnect the battery negative cable.
Remove the upper timing cover (1).
Rotate the engine using the screw (2)of the crankshaft pulley.
NOTE:The locking hole is located under the crankshaft bearing cap cover.
Undo the screw (2).
Detension the auxiliary drive belt dynamic tensioner roller, using tool [2].
C2 C3 C3 PLURIEL XSARA