2004 Citroen C3 PLURIEL Gearbox control

Downloaded from www.Manualslib.com manuals search engine 330
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Tools.
[1] Tool for positioning the gear lever: 9607T.
Adjustements.
WARNING: Cables should be adjusted each
time the gearbox, gear controls or power unit
are removed.
Inside the vehicle:
Remove the trim under the gear lever.
Lock the gear lever in neutral position,
using tool
[1].
Under the bonnet: Remove the air filter assembly.
Unlock the balljoint keys at «a».
Place the gear selection and control levers on
neutral.
Lock the cable lengths with the balljoint locking
keys.
Checks.
Remove the tool [1].
Check that all the gears engage without
«tightness ».
Check that the gear lever moves identically
forwards and backwards and to right and left. If it
does not, repeat the adjustment.
Refit the trim under the gear lever.
Refit the air filter assembly.
Adjusting the gear controls Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
XSARA XSARA PICASSO
B2CP3C6CB2CP3C0C

Downloaded from www.Manualslib.com manuals search engine 340
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
In passenger compartment.The gear selector is guided by the shape of the stepped gate and by a retaining spring which
pulls it to the left hand side.
The gear selector control has
5 positions:
Position
«P»: Park (locking and immobilisation of the vehicle).
Position «R»:Reverse gear.
Position «N»: Neutral.
Position «D»: Drive (use of the 4 gears in their autoadaptive automatic function).
Position «M»: Manual (this position lets the driver select his own gears in sequential mode
by pulling the gear selector to «M-»or pushing it to «M+»).
NOTE:Only the positions «P»or «N»authorise the starting of the engine.
In position
«M», selection is by an electronic sensor located close to the gear lever.
The variation of flux necessary to the movement of the sensor cells is obtained by a magnet
located on the lever itself. This enables the change of status.
Engines: KFV RFN
C3 XSARA PICASSO
B2CP3H7DB2CP3MUD
XSARA PICASSOC3

Downloaded from www.Manualslib.com manuals search engine 341
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
In passenger compartment (continued).
The information is transmitted to the gearbox ECU.
NOTE:The vehicle is equipped with the «shift lock»«P».
Two switches placed on the gear control gate permit the driver to choose one of the following
three driving programmes:

Normal programme: Operates as the default programme (eco law, autoadaptive mode).
Sport programme (a): Permits a more dynamic, sporty performance.
Snow programme (b): Facilitates starting and adhesion on slippery surfaces.
To return to the normal programme, press a second time on the sport switch or snow switch.
Engine: KFV
C3
B2CP3DKD

Downloaded from www.Manualslib.com manuals search engine 342
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Gearbox end.
The automatic gearbox is controlled by a cable.
«c»or «d»Pushbutton.
(1)Control lever with balljoint.
(2)Automatic adjustment (pull out the button to adjust the control, push it in to lock the
adjustment of the control).
(3)Sleeve stop.
(4)Selection control locking clip (5)on the sleeve stop(3).
Engines: KFV RFN
C3 XSARA PICASSO
B2CP3H8CB2CP3N7C
XSARA PICASSOC3

Downloaded from www.Manualslib.com manuals search engine 343
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
In passenger compartment.
The selector control has 6 positions:
The gear selector is guided by the shape of the stepped gate and by a retaining spring
which pulls it to the left hand side.
Push the lever to the right to exit from position
«P».
NOTE:The vehicle is equipped with the «shift lock»«P».
P:Park (system locked).R:Reverse gear.N:Neutral.D:Automatic (1st to 4th gear).3:Automatic (1st to 3rd gear).2:Automatic (1st to 2nd gear).
A switch located to the left of the gear control allows the driver to choose from these
programmes:
Normal:Conventional use of the automatic gearbox.Sport:This programme favours performance.Snow:In position «D», starting is in 2nd gear for dieseland in 3rd gear for petrol.
NOTE:Only the positions «P»or «N»authorise the starting of the engine.
Engines: NFU RFN RHZ
XSARA
B2CP3ADC
XSARA

Downloaded from www.Manualslib.com manuals search engine 344
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Gearbox end.
(1)
Control lever.
(2)Automatic adjustment.
(3) Sleeve stop.
The automatic gearbox is controlled by a cable.
Engines: NFU RFN RHZ
XSARA
XSARA

Downloaded from www.Manualslib.com manuals search engine 347
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
SHIFT LOCK.
NOTE:
The «shift lock»«P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).
NOTE:It is impossible to unlock the «shift lock»
«Shift lock»
«shift lock»by pressing at «a»with a screwdriver placed in the gear selection
control gate.
Move the gear selection lever out of position
«P».
Engine: RFN
XSARA PICASSO
B2CP3N8C

Downloaded from www.Manualslib.com manuals search engine 348
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Refitting the gearbox control.
New gear selection control
Couple the balljoint (3).
Push in the component (a)without bending the cable.
Check all the gear selection control positions.
Reused gear selection control.
Release the component (a).
Couple the balljoint (3).
Push in the component (a)without bending the cable.
Check all the gear selection control positions.
Engine: KFV
C3
C3
B2CP3GYD