2004 Citroen BERLINGO engine coolant

Downloaded from www.Manualslib.com manuals search engine 213
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: WJY
Setting the timing (continued).
Peg the camshaft hub, using tool [4].
Peg the injection pump hub, using tool [3].
Slacken screws (5)and (6).
Slacken screw (9)of the tensioner roller (8).
Remove the timing belt.
Refitting. Retighten screws (5)and (6)by hand.
Turn the pinions (10)and (7)clockwise in order to place them at end of slots.
Fit the timing belt on the crankshaft. Hold the belt, using tool
[5].
Position the timing belt in the following sequence:
Guide roller
(11).
Injection pump pinion (7).
Camshaft pinion (10).
Coolant pump pinion
(12).
Tensioner roller (8).
B1EP16PDB1EP1EDCB1EP132C
XSARA
B1EP1EEC

Downloaded from www.Manualslib.com manuals search engine 219
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Uncouple, plug and move aside, using tool [7], the fuel delivery pipe (2)and return
pipe (1).
Remove:
Screws
(3), (4) and (6).
Screw (7).
The upper timing cover (5).
WARNING:Refit screw (7)equipped with a spacer (17 mm thick), tighten the
screw (7)to 1,5 ± 0,1 m. daN.
NOTE:The screw (7)is one of the screws securing the coolant pump and is there
for its sealing.
Put the gear lever in 5th gear.Turn the road wheel to turn the engine in its direction of rotation.
Orient the camshaft pulley in the pegging position, use a mirror if necessary.
Peg the camshaft, using tool
[5].
Peg the engine flywheel, using tool
[3].
B1EP1A7CB1BP2H3CB1BP2H2CB1BP2R2C
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 221
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Slacken the screw (17)of the tensioner roller (18).
Remove the timing belt
(14).
Checks.
IMPERATIVE: Just before refitting, carry out the checks below.
Check that:
The rollers
(18)and (15)turn freely (without play and without any tight spot).
The coolant pump pulley
(16)turns freely (without play and without any tight spot).
There are no traces of oil leaks from the crankshaft and camshaft seals, etc.
The crankshaft pinion travels freely on the keyway.
Replace defective components if necessary.
Peg the crankshaft pinion
(19)by inserting tool [9]on the LH side of the keyway.
B1EP1A8DB1EP1A9C
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 222
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Reposition the timimg belt, belt at «a»well tensioned, in the following order:
Fuel high pressure pump pulley
(21).
Guide roller
(15).
Crankshaft pinion
(19).
Coolant pump pinion
(16).
Tensioner roller
(18).
Position tool
[1]on the belt at «a».
Remove tools
[4]and [9].
Turn the tensioner roller
(18)anticlockwise, using tool [2], to attain an overtension of:
98 ± 2 SEEM units.
Tighten screw
(17)of the tensioner roller to 2,5 ± 0,2 m.da N.
Lock the flywheel by means of tool
[6].
Tighten the accessories drive pulley screw
(8)to 7 ± 0,7 m.da N.
Remove tools
[1], [3], [5] and [6].
Rotate the crankshaft eight times in the normal direction of rotation.
Peg:
The crankshaft, using tool
[3].
The camshaft drive pulley, using tool
[5].
B1EP1ABDB1EP1ACC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 231
ENGINE
ALL TYPES FILLING AND BLEEDING THE COOLING CIRCUIT
Tools.
[1]
Filling cylinder: 4520T
[2]Adaptor for filling cylinder: 4222T
IMPERATIVE: Respect the safety and cleanliness requirements.
The draining and refilling operations can be carried out using WINN’S or similar coolant fluid replacement
equipment;it is essential to follow the instructions as stated for that equipment.
Filling and bleeding.
Fit the cylinder adaptor [2] 4222T (Picasso,C2,C3)and the filling cylinder [1] 4520T (all types).
Use the coolant to ensure protection between 15°C and 37°C.
Slowly fill the system.
NOTE:Keep the cylinder filled up (visible level).
Close each bleed screw as soon as the coolant flows without air bubbles.
Start the engine :Engine speed
1500 rpm.
Maintain this speed until the first cooling cycle (cooling fans cut in and cut out).
Stop the engine and allow it to cool down.
Remove the filling cylinder
[1] 4520T (all types)and the cylinder adaptor [2] 4222T.
Top up the system to the max. mark, with the engine cold.
Refit the filler cap.
E5AP1GNCB1GP00AC

Downloaded from www.Manualslib.com manuals search engine 233
INJECTION
Emission standard Engine type
Injection make
and type
PETROL INJECTION
Air temperature sensor
resistive value (ohms)
C2
M. MARELLI 48P2 SAGEM S2000 BOSCH M.7.4.4.
Fuel pressure (bars)
Overspeed cutoff (rpm)
Injector resistive value (ohms)
Engine coolant temperature
sensor resistive value (ohms)
Idling actuator or stepper
motor resistive value (ohms)
HFX KFV NFU
L4/IFL5 L4/IFL5 IFL5
1.1i 1.4i 1.6i 16V
333
5500 5500 6600
14,5 12,2 14,5
Stepper motor: 53 3 800 at 10°C 2500 at 20° C 800 at 50°C 230 at 90° C
3 800 at 10°C 2500 at 20° C 800 at 50°C 230 at 90° C
C2

Downloaded from www.Manualslib.com manuals search engine 234
INJECTION
Emission standard Engine type
Injection make
and type
PETROL INJECTION
C3 C3 PLURIEL
Air temperature sensor
resistive value (ohms)
C3 PLURIEL
C3
M. MARELLI
48P2M. MARELLI
6LP SAGEM
S2000BOSCH
M.7.4.4.SAGEM
S2000BOSCH
M.7.4.4.
Fuel pressure (bars)
Overspeed cutoff (rpm)
Injector resistive value (ohms)
Engine coolant temperature
sensor resistive value (ohms)
Idling actuator or stepper
motor resistive value (ohms)
HFX
K’L4INFL4/IFL5 L5 K’L4INFL4/IFL5 L4 L4/IFL5 IFL5
1.1i 1.4i 1.4i 16V 1.6i 16V
1.6i 16V
1.4i
KFU
KFV NFU KFV NFU
3,53,5
3,5
3,5 3,5 3,5
14,5 14,5 14,5
12,214,5 14,5
5500
5800
5500
5500
5500 5800
Stepper motor:53 3800 at 10° C 2 500 at 20° C 800 at 50° C 230 at 90° C
3800 at 10° C 2 500 at 20° C 800 at 50° C 230 at 90° C

Downloaded from www.Manualslib.com manuals search engine 235
INJECTION
Emission standard Engine type
Injection make
and type
PETROL INJECTION
XSARA XSARA PICASSO
Air temperature sensor
resistive value (ohms)
XSARA PICASSO
XSARA 2
SAGEM
S2000M. MARELLI
6LP BOSCH
M.7.4.4.BOSCH
M.7.4.4.SAGEM
S2000M. MARELLI
6LP
Fuel pressure (bars)
Overspeed cutoff (rpm)
Injector resistive value (ohms)
Engine coolant temperature
sensor resistive value (ohms)
Idling actuator or stepper
motor resistive value (ohms)
KFW
L4/IFL5/L5 L4/IFL5 L4/IFL5 L4 IFL5L4/IFL5
1.4i 1.6i 16V 2.0i 16V 1.6i
2.0i 16V
1.8i 16V
RFN
NFU NFV 6FZ RFN
3,53,5
3
3 3,5 3,5
14,5 14,5 14,5
14,512,2 14,5
5500
5700
6000
5800
5500 6000
Stepper motor:53 3800 at 10° C 2 500 at 20° C 800 at 50° C 230 at 90° C
3800 at 10° C 2 500 at 20° C 800 at 50° C 230 at 90° C