2004 Citroen BERLINGO cold

Downloaded from www.Manualslib.com manuals search engine 59
GENERAL
LUBRICANTS TOTAL recommended oils
POWER STEERING OILS
ENGINE COOLANT FLUID
ALL TYPES
TOTAL FLUIDE ATX
TOTAL FLUIDE DAS
Special oil distributed by
CITROËN
Part No.: 9730 A1
Power steering
All countries
Very cold countries
All countriesCITROËN fluid
Protection: 35C°
2Litres
5Litres
20 Litres
210Litres
9979 70
9979 71
9979 769979 779979 72
9979 73
9979 749979 75 PackCITROËN Part No.
REVKOGEL 2000
GL YSANTIN G33

Downloaded from www.Manualslib.com manuals search engine 60
GENERAL
LUBRICANTS TOTAL recommended oils
BRAKE FLUIDS
Synthetic brake fluid
HYDRAULIC CIRCUIT
WARNING: TOTAL FLUIDE LDS fluid cannot be blended with TOTAL LHM.
WARNING: CITROËN C5: Use exclusively TOTAL FLUIDE LDS suspension fluid.
All countriesTOTAL HYDRAURINCAGE
All countriesCITROËN fluid
0,5Litre
1 Litre
5 Litres
9979 05
9979 069979 07 Pack
CITROËN Part No.
ALL TYPES
Pack
CITROËN Part No.
Norm
Colour
All countries
TOTAL FLUIDE LDS
TOTAL LHM PLUS
TOTAL LHM PLUS
Very cold countries Orange 9979 69
ZCP 830095
9979 20 Green1
Litre

Downloaded from www.Manualslib.com manuals search engine 226
ENGINEVALVE CLEARANCE SETTINGS
The valve clearances must be checked with the engine cold
Inlet
Petrol all types(Except16VNFU)
NFU
Petrol 16V all types
1.4 HDi
1.4 HDi 16V
Diesel 2.0 HDi
Diesel all types(Except Diesel 1.4 HDi
1.4 HDi 16V
2.0 HDi)0,20 mm ± 0,05Exhaust
0,40 mm ± 0,05
Hydraulic adjustment 1 mm ± 0,05
1 mm ± 0,05
Rocking
Adjust
1
1
3
3
4
4
2
24
4
2
2
1
1
3
3
Inlet

Adjust Rocking
Valves fully
openAdjust
1
3423 4
4
2
2
1
1
3
Fully open (Exhaust)
POSSIBLE PROCEDURES
For engines with 4 cylinders in a line (1342 )
Engines without hydraulic
adjustment: the clearance (J)should be checked opposite the
cam.
B1DP13QC
0,15 mm ± 0,08
0,30 mm ±0,08

Downloaded from www.Manualslib.com manuals search engine 231
ENGINE
ALL TYPES FILLING AND BLEEDING THE COOLING CIRCUIT
Tools.
[1]
Filling cylinder: 4520T
[2]Adaptor for filling cylinder: 4222T
IMPERATIVE: Respect the safety and cleanliness requirements.
The draining and refilling operations can be carried out using WINN’S or similar coolant fluid replacement
equipment;it is essential to follow the instructions as stated for that equipment.
Filling and bleeding.
Fit the cylinder adaptor [2] 4222T (Picasso,C2,C3)and the filling cylinder [1] 4520T (all types).
Use the coolant to ensure protection between 15°C and 37°C.
Slowly fill the system.
NOTE:Keep the cylinder filled up (visible level).
Close each bleed screw as soon as the coolant flows without air bubbles.
Start the engine :Engine speed
1500 rpm.
Maintain this speed until the first cooling cycle (cooling fans cut in and cut out).
Stop the engine and allow it to cool down.
Remove the filling cylinder
[1] 4520T (all types)and the cylinder adaptor [2] 4222T.
Top up the system to the max. mark, with the engine cold.
Refit the filler cap.
E5AP1GNCB1GP00AC

Downloaded from www.Manualslib.com manuals search engine 255
INJECTION
ADJUSTING THE MECHANICAL CONTROLS OF THE DELPHI INJECTION PUMP
Engine: WJY
Adjusting the fast idle.
Engine cold.
Ensure that the lever (2)is up against its stop to the right.
If not, adjust the tension of the cable (3)using the cable clamp (1).
Finish tensioning using the sleeve tensioner (4).
Engine hot. Check that the cable (3)is in tension.
Checking the thermostatic sensor. There should be a minimum 6 mmcable travel between a cold and a hot engine.
Adjusting the accelerator control.
Prior conditions.
Engine hot (cooling fan is engaged twice).
Checking the accelerator cable tension. Fully depress the accelerator pedal.
Check that the lever (6)is against its stop (5)otherwise, alter the position of the pin.
If not, adjust the position of the accelerator cable tensioning retaining pin.
Ensure that in the idle position the lever
(6)is against the stop (7).
B1HP0K9C
XSARA

Downloaded from www.Manualslib.com manuals search engine 459
ELECTRICAL
SYSTEM
STARTER MOTORS
Abbreviations and definitions
ALL TYPES
Coding of climates is as follows:
CLIMATES:C Hot
: Starting possible as low as 18°C.
T Temperate: Starting possible as low as 18°C.
F Cold: Starting possible as low as 25°C.
GF Very cold: Starting possible as low as 30°C.
Meaning of abbreviations:
BV
: Gearbox.
M: Manual gearbox.
A: Automatic gearbox.
MAP: Piloted manual gearbox.
DA: Powerassisted steering.
REFRI: Air conditioning.

Downloaded from www.Manualslib.com manuals search engine ALTERNATORS
Abbreviations and definitions
ALL TYPES
Coding of climates is as follows:
CLIMATES:
C
: Hot (45°C/37°C).
T: Temperate (37°C/17°C).
F: Cold (17°C/25°C).
GF : Very cold (<25°C).
Meaning of abbreviations:
BV
: Gearbox.BVM: Manual gearbox.BVA: Automatic gearbox.BVMP: Piloted manual gearbox.NON REFRI: Without air conditioning.REFRI: With air conditioning.DA: Powerassisted steering.GEP: Electropump motor.DP: Double lug.3 Pts: 3Point.NC: Not marketed.TT: All Types.N: Level.SOP: Without Option.TOP: All Options.L.C.: Heated rear screen.DAG:Left hand drive.DAD:Right hand drive.
472
ELECTRICAL
SYSTEM

Downloaded from www.Manualslib.com manuals search engine 473
ELECTRICAL
SYSTEM
ALTERNATORS
Allocation of alternator classes
C2
Meaning of abbreviations, see page:472.
Without aircon With aircon
Without cold pack With cold pack Without cold pack With cold pack
RT3
RT3RT3
RT3RT3
RT3RT3
RT3
Engine Gearbox Climate Base N1 or
N3Base N1 or
N3Base N1 or
N3Base N1 or
N3
N2 N2 N2 N2
C
8
88
81.1iT
BVM F77
77
7GF
C
791.4i T77 8BVMPF8778GF88C791.6i 16V T77 8BVMF8778GF88C
1.4 HDiT15BVM F
GF