2004 CHEVROLET TRACKER reset

Resuming a Set Speed
If you set your cruise control at a desired speed then
suspend cruise by applying the brake, by pressing
the clutch pedal if you have a manual transmission or
by pressing CANCEL, you don't need to reset it.
You may resume your previously set speed by brie¯y
turning the switch to RESUME ACCEL (Accelerate),
provided your speed has not dropped below 25 mph
(40 km/h). If your speed has dropped below 25 mph
(40 km/h), accelerate to 25 mph (40 km/h) or greater
then turn the switch to RESUME ACCEL. There is
a short time delay after your speed is suspended until
you can reset the cruise control to your desired speed.
Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed.
·Use the accelerator pedal to go to a higher speed.
Turn the switch on the lever down to COAST SET
and release it. Take your foot off the accelerator
pedal. You'll now cruise at the higher speed.
·Turn the switch on the lever up to RESUME
ACCEL. Hold the switch at RESUME ACCEL until
you get up to the speed you want, then release
the switch.
Reducing Speed While Using Cruise
Control
To reduce your speed, turn the switch and hold it down
in the COAST SET position until you reach the lower
speed you want, then release the switch.
3-11

{CAUTION:
Your regular brake system may not be working
properly if the anti-lock brake system warning
light is on. Driving with the anti-lock brake
system warning light on can lead to an
accident. After you have pulled off the road
and stopped carefully, have the vehicle towed
for service.
If the anti-lock brake system warning light stays on
longer than normal after you've started your engine, turn
the ignition off. Or, if the light comes on and stays on
when you're driving, stop as soon as possible and turn
the ignition off. Then start the engine again to reset
the system. If the light still stays on, or comes on again
while you're driving, your vehicle needs service. If
the light is on and the regular brake system warning
light isn't on, you still have brakes, but you don't have
anti-lock brakes.
The anti-lock brake system warning light should come
on brie¯y when you turn the ignition key to ON. If
the light doesn't come on then, have it ®xed so it will be
ready to warn you if there is a problem.
Engine Coolant Temperature Gage
This gage shows the
engine coolant
temperature. If the gage
pointer moves to the
H (red) side, your engine
is too hot.
It means that your engine coolant has overheated and
you should stop your vehicle and turn off the engine
as soon as possible.
See
Engine Overheating on page 5-28.
3-32

Radio with CD
Playing the Radio
PWR (Power):Press this knob to turn the system
on and off.
VOL (Volume):Turn this knob to increase or to
decrease volume.
RCL (Recall):Press this knob to switch the display
between the radio station frequency and the time.
Time display is available with the ignition turned off.
Finding a Station
AM FM:Press this button to switch between FM1,
FM2, and AM. The display will show your selection.
TUNE:Turn this knob to select radio stations.
oSEEKp:Press the right or the left arrow to go to
the next or to the previous station and stay there.
To scan stations, press and hold either SEEK arrow for
two seconds until you hear a beep. The radio will go
to a station, play for a few seconds, then go on to
the next station. Press either SEEK arrow again to stop
scanning.
To scan preset stations, press and hold either SEEK
arrow for more than four seconds until you hear
two beeps. The radio will go to the ®rst preset station
stored on your pushbuttons, play for a few seconds, then
go on to the next preset station. Press either SEEK
arrow again to stop scanning presets.
The radio will seek and scan only to stations that are in
the selected band and only to those with a strong
signal.
3-40

Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six FM1, six FM2, and six AM) by performing the
following steps:
1. Turn the radio on.
2. Press AM FM to select FM1, FM2, or AM.
3. Tune in the desired station.
4. Press and hold one of the six numbered
pushbuttons until you hear a beep. Whenever you
press that numbered pushbutton, the station
you set will return.
5. Repeat the steps for each pushbutton.
Setting the Tone (Bass/Treble)
AUDIO:To adjust the bass or the treble, press and
release the AUDIO button repeatedly until BAS or TRE
appears on the display. Then press and hold the up
or the down arrow to increase or to decrease. If a station
is weak or noisy, you may want to decrease the
treble.
To adjust bass or treble to the middle position, select
BAS or TRE. Then press and hold the AUDIO button for
more than two seconds until you hear a beep. B and
a zero or T and a zero will appear on the display.
To adjust both tone controls and both speaker controls
to the middle position, ®rst end out of audio mode
by pressing another button, causing the radio to perform
that function, or by waiting ®ve seconds for the display
to return to time of day. Then press and hold the AUDIO
button for more than two seconds until you hear a
beep. CEN will appear on the display.
3-41

Temperature ± A, B, C
The temperature grades are A (the highest), B, and C,
representing the tire's resistance to the generation
of heat and its ability to dissipate heat when tested
under controlled conditions on a speci®ed indoor
laboratory test wheel. Sustained high temperature can
cause the material of the tire to degenerate and
reduce tire life, and excessive temperature can lead to
sudden tire failure. The grade C corresponds to a
level of performance which all passenger car tires must
meet under the Federal Motor Vehicle Safety Standard
No. 109. Grades B and A represent higher levels of
performance on the laboratory test wheel than the
minimum required by law.
Warning: The temperature grade for this tire is
established for a tire that is properly in¯ated and not
overloaded. Excessive speed, underin¯ation, or
excessive loading, either separately or in combination,
can cause heat buildup and possible tire failure.
Wheel Alignment and Tire Balance
The wheels on your vehicle were aligned and balanced
carefully at the factory to give you the longest tire life
and best overall performance.
Scheduled wheel alignment and wheel balancing are
not needed. However, if you notice unusual tire wear or
your vehicle pulling one way or the other, the alignment
may need to be reset. If you notice your vehicle
vibrating when driving on a smooth road, your wheels
may need to be rebalanced.
5-69

Restraint Systems
Checking....................................................1-59
Replacing Parts...........................................1-60
Resynchronization............................................. 2-6
Right Front Passenger Position, Safety Belts......1-24
Roadside
Assistance Program....................................... 7-5
Rocking Your Vehicle To Get It Out...................4-45
Routing, Engine Drive Belt..............................5-101
Running Your Engine While You Are Parked.......2-30
S
Safety Belt
Reminder Light............................................3-28
Safety Belts
Care of......................................................5-88
Center Passenger Position............................1-24
Driver Position............................................1-15
How to Wear Safety Belts Properly................1-14
Questions and Answers About Safety Belts.....1-13
Rear Seat Passengers.................................1-26
Right Front Passenger Position......................1-24
Safety Belt Extender....................................1-28
Safety Belt Use During Pregnancy.................1-23
Safety Belts Are for Everyone......................... 1-9
Safety Chains.................................................4-60
Safety Warnings and Symbols.............................. iii
Scanning the Terrain.......................................4-19Seats
Head Restraints............................................ 1-5
Manual........................................................ 1-2
Manual Lumbar............................................. 1-3
Rear Seat Operation...................................... 1-5
Reclining Seatbacks...................................... 1-3
Securing a Child Restraint
Center Rear Seat Position............................1-47
Designed for the LATCH System...................1-44
Rear Outside Seat Position...........................1-44
Right Front Seat Position..............................1-49
Security While You Travel.................................. 7-5
Selecting the Right Schedule, Maintenance.......... 6-4
Service........................................................... 5-3
Adding Equipment to the Outside of Your
Vehicle..................................................... 5-4
Doing Your Own Work................................... 5-3
Engine Soon Light.......................................3-33
Publications Ordering Information...................7-11
Service Bulletins.............................................7-11
Service Engine Soon Light...............................3-33
Service Manuals.............................................7-11
Setting Preset Stations....................................3-41
Setting the Time.............................................3-39
Setting the Tone (Bass/Treble)..........................3-41
Sheet Metal Damage.......................................5-91
Shift Speeds..................................................2-21
Shifting Into or Out of FOUR-WHEEL
LOW (4L)...................................................2-23
Shifting Into Park (P).......................................2-25
11