2004 BMW X3 3.0I wiper blades

Driving
42 5Serrated dial for adjustment of the wipe
interval or the sensitivity of the rain sen-
sor
Retracted position
The right wiper is partially concealed by the
hood.
To move the wipers into a vertical position:
1.Switch on wipers in lever position 1
2.When the wipers are approximately
vertical, move the ignition key to
position 0.
For changing the wiper blades, refer to
page 99.
Fold the wipers back down onto the
windshield before you turn the igni-
tion key to position 1 or 2 again. If you do
not, they could be damaged.<
Intermittent mode
Not on vehicles with rain sensor.
You can set the wipe interval to four stages
with the serrated dial 5.
In addition, the wipe interval is varied auto-
matically depending on road speed.
Rain sensor*
The rain sensor is positioned on the wind-
shield, directly in front of the interior rear-
view mirror.
Deactivate the rain sensor when
passing through an automatic car
wash. Failure to do so could result in dam-
age caused by undesired wiper activa-
tion.<
Activating
>Move the lever to position 1 with the
ignition key in position 1 or higher. The
wipers travel once across the wind-
shield, regardless of the weather condi-
tions.
You can leave the lever permanently in
position 1 and then only need to activate
the rain sensor as of ignition key position 1.
To do so:
>Briefly turn the serrated dial 5 or>Cleaning windshield 1, refer to next
section.
Adjust sensitivity: turn the serrated dial 5.
Deactivating
>Move lever to position 0.
Normal wipe
The system switches automatically to inter-
mittent mode when the vehicle is not mov-
ing, not on vehicles with rain sensor.
Fast wipe
The wipers operate at normal speed when
the vehicle is not moving, not on vehicles
with rain sensor.
Cleaning windshield, rear window
and headlamps*
0Wipers retracted
1To clean windshield and headlamps
2Rear window wiper intermittent mode
3Clean the rear window
Do not use the washers if there is any
danger that the fluid will freeze on the
windshield. If you do so, your vision could
be obscured. To avoid freezing, use a
washer fluid antifreeze, refer to page 94.
Do not use the washers when the reservoir
is empty. This could cause damage to the
washer pump.<
Cleaning the windshield
The system sprays washer fluid against the
windshield and activates the wipers for a
brief period.
The windshield washer nozzles are auto-

Reference
At a glance
Controls
Driving tips
Mobility
43
matically heated as of ignition key
position 2.
Cleaning headlamps*
When the vehicle lighting system is
switched on, the headlamps are cleaned at
regular and appropriate intervals.
Rear window wiper
Rear window wiper in intermittent mode.
When reverse gear is engaged, the wiper
operates continuously.
You can also program the interval:
1.Briefly move the wiper lever from posi-
tion 0 to position 2
2.Wait for desired interval; maximum of
30 seconds
3.Move the wiper lever from position 0 to
position 2 again
To change the wiper blades, refer to
page 99.
Cruise control*
The vehicle maintains and stores the speed
that you set as of a speed of approx.
20 mph/30 km/h.
You can use cruise control whenever the
system is active while the engine is run-
ning.
Indicator lamp
Indicator lamp in the instrument
cluster lights up green:
System ready for operation using
the buttons in the steering wheel.
Activating the system
From ignition key position 2:
Press button in steering wheel; the indica-
tor lamp in the instrument cluster comes
on. You are able to use the cruise control.
Do not use the cruise control when
driving on winding roads, in heavy
traffic or in poor road conditions Ð e.g. snow, rain, ice, loose road surface Ð that do
not permit a constant speed.<
Deactivating system
Press the button repeatedly until the indi-
cator lamp in the instrument cluster goes
out.
The cruise control is also deactivated when
the ignition key is turned to position 0. The
speed stored in the memory is deleted in
the process.
Maintaining and storing speed or
accelerating
Briefly press button +:
The system maintains and stores the cur-
rent vehicle speed. Every time you briefly
press the button, the vehicle's speed
increases by roughly 1Ðmph/1 km/h.
Press and hold button
+:
The vehicle accelerates without pressure
on the accelerator pedal. When you release
the button, the system maintains and
stores the current speed.
If, on a downhill gradient, the engine's
braking effect is not sufficient, the
controlled speed can be exceeded. Speed
can drop on uphill grades if the engine out-
put is insufficient.<
Decelerating
Briefly press button Ð:
Every time you briefly press the button,
the vehicle's speed decreases by roughly
1 mph/1 km/h if you are already driving
with cruise control.
Press and hold button
Ð:
With the cruise control active, the system
automatically reduces the throttle opening
to slow the vehicle. When you release the
button, the system maintains and stores
the current speed.

Reference
At a glance
Controls
Driving tips
Mobility
99
Replacing components
Onboard tool kit
The onboard tool kit is located in a com-
partment on the left under the cargo area.
Replacing wiper blades
Front
1.Move the wiper to a fold-out position,
refer to page 42
2.Lift the wiper arm and press the secur-
ing spring, refer to arrow
3.Pull the wiper blade off toward the
wiper arm
4.Insert the new blade and snap it into
place.
Fold the wipers back down onto the
windshield before you turn the igni-
tion key to position 1 or 2 again. If you do
not, they could be damaged.<
Rear
1.Lift the wiper arm
2.Pull off the wiper blade, refer to arrow
3.Insert a new wiper blade.
Lamps and bulbs
The lamps and bulbs make essential contri-
butions to the safety of your vehicle. There-
fore, comply fully with the following instruc-
tions during bulb replacement. If you are
not familiar with the specified procedures,
BMW recommends having the replace-
ments carried out at your BMW Sports
Activity Vehicle Center.
Never touch the glass of new bulbs
with your bare fingers, as even minute
amounts of contamination will burn into the
bulb's surface and reduce its service life.
To install, use a clean cloth, napkin etc. or
hold the bulb by its metal socket.<
A replacement bulb set is available from
your BMW Sports Activity Vehicle Center.
To prevent short circuits, before
working on any electrical system,
equipment or accessory you should always
switch it off and disconnect the cable from
the battery's negative terminal before start-
ing.
To avoid possible injury or equipment dam-
age when changing bulbs, observe any
instructions provided by the bulb manufac-
turer.<