Cockpit
12
Indicator and warning
lamps
Technology that monitors itself
The indicator and warning lamps identified
by the
+ symbol are subjected to an oper-
ation check each time you switch on the
engine. They each light up once for differ-
ent periods of time.
When a malfunction occurs in a monitored
system, the corresponding lamp will either
fail to go out when the engine is started, or
it will come on again during normal driving.
Detailed information is provided on the
specified pages.
Please fasten safety belt
+ 30
Airbags
+ 54
Brake system
+
With handbrake released 52/ 96
With handbrake set 38
With other warning lamps 52
Brake warning lamp for Canadian
models
Driving stability control systems/
Antilock Brake System
+ 53
Antilock Brake System ABS/
Chassis control system for Cana-
dian models
Brake pads
+ 96
Dynamic Stability Control DSC/
xDrive
+ 50/ 52
Flat Tire Monitor
+ 53
Automatic transmission
+ 39
Engine oil + 94
Service Engine Soon
+ 98
Service Engine Soon
+ 37
warning lamp for Canadian
models.
Check Gas Cap
+
Engine electronics + 37
Battery charge current
+ 105
Topping up coolant 95
Topping up washer fluid 94
Lamp defective 57
Turn signal indicators 41
Fog lamps 58
Headlamp flasher 41
High beams 58
Cruise control 43
Reference
At a glance
Controls
Driving tips
Mobility
37
Driving
Ignition lock
0 Steering locked
The key can only be inserted or removed in
this position.
After removing the key, turn the steering
wheel slightly to the left or right until you
hear the lock engage.
Vehicles with automatic transmission:
Only move the selector lever from
position P with the engine running. To turn
the key back to position 0 or to remove it,
first place the selector lever in position P:
Interlock.<
1 Steering unlocked
A slight steering wheel movement often
makes it easier to turn the key from 0 to 1.
Individual current consumers are ready for
operation.
2 Ignition switched on
All vehicle systems are ready for operation.
3 Engine start
Engine
Do not allow the engine to warm up while
idling. Drive off immediately at moderate
engine speed.
Engine idle speed is controlled by the
engine computer system. Increased
speeds at startup are normal and should decrease as the engine warms up. If engine
speed does not decrease, service is
required.
To prevent the battery from discharging,
always switch off electrical devices which
are not in use and the ignition when the
vehicle is not being driven.
Do not run the engine in closed
rooms, as otherwise inhaling toxic
exhaust gases can cause unconsciousness
and death. The exhaust gases contain car-
bon monoxide, an odorless and colorless,
but highly toxic gas. Do not leave the vehi-
cle unattended with the engine running,
since an unattended vehicle with a running
engine represents a safety hazard.
When driving, standing at idle and while
parking take care to avoid possible contact
between a hot exhaust system and any
highly flammable materials such as hay,
leaves, grass, etc. Such contact could lead
to a fire, resulting in serious personal injury
and property damage.<
Indicator lamps
If the Service Engine Soon indicator
lamp comes on either continuously
or intermittently, this indicates a
fault in the emissions-related electronic
systems. Although the vehicle remains
operational, you should have the systems
checked by your BMW Sports Activity
Vehicle Center at the earliest possible
opportunity.
The illuminated indicator informs you of the
need for service, not that you need to stop
the vehicle. However, the systems should
be checked by your BMW Sports Activity
Vehicle Center at the next opportunity.
If the indicator blinks or flashes, this indi-
cates a high level of engine misfire. Reduce
speed and contact the nearest BMW
Sports Activity Vehicle Center immediately.
Severe engine misfiring over even a short
period of time can seriously damage emis-
Driving
38 sion control system components, espe-
cially the catalytic converter.
Service Engine Soon indicator lamp
for Canadian models.
Malfunction in the engine electron-
ics.
You can continue to drive with
reduced engine output or engine speed.
Please have it checked by your BMW
Sports Activity Vehicle Center.
Starting the engine
When starting the engine, do not press the
accelerator pedal.
Vehicles with manual transmission:
Step on the clutch when starting the
vehicle. A lockout prevents the engine from
starting if the clutch is not depressed.<
Do not actuate the starter for too
short a time. Do not turn it for more
than approx. 20 seconds. Release the igni-
tion key immediately as soon as the engine
starts.<
If the engine fails to start on the first
attempt, for instance, if it is very hot or cold:
>Press the accelerator pedal halfway
down while engaging the starter.
During a cold start at very low tempera-
tures, as of approx. +57/Ð156, at high
altitudes over 3,300 ft/1,000 m:
>For the first attempt, run the start for
longer, approx. 10 seconds
>Press the accelerator pedal halfway
down while engaging the starter.
Avoid frequent starting is quick suc-
cession or repeated start attempts in
which the engine does not start. Otherwise,
the fuel is not burned or inadequately
burned and there is a danger of overheat-
ing and damaging the catalytic converter.<
Manual transmission
1.Engage the handbrake
2.Gearshift lever in idle position
3.Press the clutch pedal
4.Start the engine.Before leaving the vehicle with the
engine running, place the gearshift
lever in idle position and apply the hand-
brake.
Never leave an unattended vehicle with the
engine running, as such a vehicle repre-
sents a potential safety hazard.<
Automatic transmission
1.Press the brake pedal
2.Place the selector lever in position P
or N
3.Start the engine.
To prevent the vehicle from rolling,
always select position P and engage
the handbrake before leaving the vehicle
with the engine running.
Never leave an unattended vehicle with the
engine running, as such a vehicle repre-
sents a potential safety hazard.<
Switching off the engine
Do not remove the ignition key when
the vehicle is moving, as otherwise
the steering could lock.
When leaving the vehicle, always remove
the ignition key and lock the steering.
When parking on downward inclines, apply
the handbrake.<
Manual transmission
Turn the ignition key to position 1 or 0.
Automatic transmission
Engage selector-lever position P, turn igni-
tion key to position 1 or 0.
Handbrake
The handbrake is primarily intended to pre-
vent the vehicle from rolling while parked; it
brakes the rear wheels.
Indicator lamp
The indicator lamp lights up from
ignition switch position 2 with the
handbrake set Ð an acoustic signal
also sounds when starting off.
Everything under control
46
Between the blue and red fields
Normal operating range. The dial may wan-
der into the red field.
Red
Comes on while driving:
The engine is overheated. Switch off the
engine immediately and allow it to cool
down.
Checking coolant level, refer to page 96.
When you switch on the ignition, the warn-
ing lamp 1 comes on briefly to confirm that
the system is operational.
Service Interval Display
Remaining distance until next
service due
The displays shown in the illustration
appear for a few seconds as of ignition key
position 1 or after starting the engine.
Together with the lettering OILSERVICE or
INSPECTION, the next scheduled service
and remaining distance to this service is
shown in miles/kilometers.
The remaining distance is determined on
the basis of the past driving style.
A flashing display and a Ð before the
numerical value mean that the service
interval has been passed by the displayed
number of miles/kilometers. Please make
an appointment with your BMW Sports
Activity Vehicle Center.
Replacing brake fluid
You can have the month and year for the
scheduled brake fluid replacement dis-
played by pressing the right button in the
instrument cluster while the next sched-
uled service is being displayed. With each
button touch, the display switches
between the scheduled service and
scheduled brake fluid replacement.
When the brake fluid replacement is due,
the clock symbol also lights up. Please
make an appointment with your BMW
Sports Activity Vehicle Center.
Immobilization periods in which the
battery is disconnected are not taken
into account by the display. Please remem-
ber that brake fluid should be changed
every two years at the latest, even if the
display does not yet indicate that service is
required, refer to page 96.<
Clock
If you want to have a permanent clock dis-
play, you can also have the time displayed
in the display of the car radio, refer to the
Owner's Manual for Radio.
You can adjust the clock, also for display in
the radio, as follows.
Technology for comfort, convenience and safety
52
Activating the system
Press the button; the indicator lamp comes
on.
The indicator lamp flashes when the brakes
are applied automatically.
Deactivating the system
Press the button again; the indicator lamp
goes out.
Above approx. 35 mph/60 km/h HDC is
immediately deactivated, and when the
ignition is switched off after approx.
10 seconds.
Using HDC
On manual transmission vehicles:
Use HDC in first gear and in reverse gear,
as in the higher gears the engine braking
effect diminishes.
On automatic transmission vehicles:
You can use HDC in every drive position.
Malfunction
If the indicator lamp in the button goes out
in the HDC mode or fails to light up when
the button is pressed:
HDC is temporarily not available, as the
brake temperature is too high.
Malfunctions of the driving stability
control systems
The red brake warning lamp lights
up together with the warning lamps
for ABS and DSC/xDrive. In addi-
tion, a warning signal sounds:
ABS, DSC and xDrive have failed.
Drive may then only be carried out
via the rear axle. Please have it checked by the nearest BMW Sports Activ-
ity Vehicle Center.
Proceed cautiously and defensively.
When driving on poor roads, refrain
from using full throttle and avoid pressing
the accelerator beyond the kickdown point.
Otherwise the drive train may be damaged
or accidents can occur.<
If the brake warning lamp lights up yellow in
the described combination, the Electronic
brake-force distribution EBV is still avail-
able.
Indicator and warning lamps for
Canadian models.
The warning lamp in the instrument
cluster lights up in yellow.
Dynamic Brake Control DBC is
defective. Have the system checked and
repaired at your BMW Sports Activity Vehi-
cle Center as soon as possible.
Warning lamp for Canadian models.
The warning lamp lights up continu-
ously and a warning signal sounds:
DSC or the xDrive all-wheel system
has failed.
The stabilizing interventions of DSC or the
all-wheel drive system xDrive are no longer
available. Drive may then only be carried
out via the rear axle. Please have it
checked by the nearest BMW Sports Activ-
ity Vehicle Center.
Proceed cautiously and defensively.
When driving on poor roads, refrain
from using full throttle and avoid pressing
the accelerator beyond the kickdown point.
Otherwise the drive train may be damaged
or accidents can occur.<
The warning lamp lights up:
Malfunction in the driving stability
control systems. HDC is no longer
Reference
At a glance
Controls
Driving tips
Mobility
53
available. See your BMW Sports Activity
Vehicle Center to have the system
repaired.
Flat Tire Monitor
The concept
The Flat Tire Monitor keeps track of the
inflation pressures in the four fitted tires as
you drive. The system provides an alert
whenever the inflation pressure drops sig-
nificantly in relation to the pressure another
tire.
The check of the tire inflation pressure is
based on monitoring the relative speeds of
the wheels. A flat tire is detected and
reported on the basis of a deviation in cer-
tain speed ratios.
Functional requirement
So that the Flat Tire Monitor can learn the
correct inflation pressure, please perform
the following:
1.Check the inflation pressures in all tires
2.Compare with the inflation pressure
table on page 87 and correct if neces-
sary
3.Initialize the system.
Limits of the system
The Flat Tire Monitor cannot indicate
sudden severe tire damage caused
by outside factors and does not detect a
natural, even pressure drop in all four
tires.<
In the following situations, on the other
hand, there can be delays in detecting tire
pressure losses, and even system failure:
>When driving on snow-covered or slip-
pery road surfaces
>In the case of performance-oriented
driving: slip on the drive wheels, high
lateral acceleration
>False alarms and undetected loss of
pressure may occur when you are driv-
ing with snow chains fitted>When driving with a compact wheel, the
Flat Tire Monitor cannot operate.
Initializing the system
Perform the initialization immediately
every time you correct the inflation
pressure, change a tire or change a wheel
or all wheels. A drive is required for this
purpose.<
1.Before the start of driving, start the
engine, but do not drive off
2.Press the button until the yellow indica-
tor lamp in the instrument cluster lights
up for a few seconds
3.Drive off.
It takes a few minutes until the Flat Tire
Monitor can detect and indicated a flat tire.
Do not initialize the system when driv-
ing with snow chains or with a com-
pact wheel.<
Flat tire
Indicator lamp
The symbol in the instrument clus-
ter lights up in yellow.
1.Reduce speed and stop the vehicle
carefully. Avoid sudden braking and
steering maneuvers
2.Identify damaged tire
If identification is not possible,
contact your BMW Sports Activity
Vehicle Center.<
3.Replace the damaged tire, refer to
Changing a wheel on page 103.
Things to remember when driving
80
Driving on bad roads
Your BMW X3 is at home on all paved and
unpaved roads. It combines all-wheel drive
with the advantages of a normal passenger
car.
Driving on unpaved terrain can cause
damage to the vehicle.<
When you are driving on bad roads, there
are a few points which you should strictly
observe Ñ for your own safety, for that of
your passengers, and for the safety of the
vehicle:
>Familiarize yourself with the vehicle
before you begin driving. Do not take
risks with the vehicle under any circum-
stances
>Always adapt the driving speed to the
road conditions. The more steep and
uneven the roadway is, the lower the
speed should be
>You can operate your vehicle on uphill
and downhill gradients with a maximum
slope of 50 %. If you wish to drive on
uphill and downhill grades of this
nature, make sure beforehand that the
engine oil and coolant levels are near
the max mark, refer to pages 94 and 96
>For very steep downhill driving, use Hill
Descent Control HDC, refer to page 51.
Driving off is possible on upward
inclines of up to 33%.
The permitted side inclination is 50 %
>While driving, watch carefully for obsta-
cles such as rocks or holes. Try to avoid
these obstacles whenever possible
>Avoid that the body makes contact with
the ground, e.g. on the crests of hills
and bumpy roads
>Do not drive in water that is deeper than
20 in/50 cm. If you must drive through
water up to that depth, drive at a walk-
ing speed and do not stop.
After leaving the water, press on the
footbrake gently several times while
driving at a low speed. The brake appli-
cations will help to dry the brakes, thus
preventing a reduction in braking per-
formance caused by the moisture. For cleaning the handbrake, apply the
lever slightly at approx. 25 mph/40 km/
h and continue to drive for approx. 200
yards/200 meters, provided that traffic
conditions allow you to do so.
Please bear the following points in mind
after driving on poor roads, in order to pre-
serve the road safety of your BMW:
>Clean the heavy dirt from the body
>Clean mud, snow, ice and other materi-
als from the wheels and tires. Check the
tires for damage.
Under the engine hood
94
Washer fluid
Windshield and headlamp washer
system
Antifreeze agent for the washer sys-
tems is inflammable. For this reason,
keep it away from sources of flame and
store it only in its original containers. Store
it so that it is inaccessible to children.
Always observe the instructions for use
provided on the containers.<
We recommend that you mix the
washer ßuid before adding it to the
reservoir.<
Capacity:
approx. 6.9 US quarts/6.5 liters.
Fill with water and, if required, with an anti-
freeze additive according to manufac-
turer's recommendations.
Engine oil
Indicator lamp
Engine oil pressure
The indicator lamp lights up red:
Stop the vehicle immediately and
switch off the engine. Check the
engine oil level; top up as required. If the oil
level is correct: contact the nearest BMW
Sports Activity Vehicle Center.
Do not continue driving. The engine
could be damaged because of inade-
quate lubrication.<
Engine oil level
The indicator lamp lights up yellow
while driving:
The oil level is at the absolute mini-
mum. Add engine oil as soon as possible.
Until then, do not drive more than
approx. 30 miles/50 km.
The indicator lamp lights up yellow
after the engine is switched off:
Top up engine oil at the earliest
opportunity Ð when refueling.
Engine oil sensor
The indicator lamp lights up yellow
within 20 seconds after starting the
engine:
The oil level sensor is defective. Please
have it checked by a BMW Sports Activity
Vehicle Center.
Checking oil level
1.Park the vehicle on a level surface
2.Switch the engine off after it has
reached normal operating temperature
3.After approx. 5 minutes, pull the dip-
stick out and wipe it off with a clean lint-
free cloth, paper towel, or similar mate-
rial
4.Carefully push the dipstick all the way
into the guide tube and pull it out again
5.The oil should extend to between the
two marks on the dipstick.
As is the case with fuel economy, the rate
at which the engine uses oil is strongly
influenced by driving style and operating
conditions.
The oil quantity between the two marks of
the dipstick is approx. 1.1 US quarts/1 liter.