2004 BMW X3 3.0I bulb

Reference
At a glance
Controls
Driving tips
Mobility
41
appear briefly in the instrument cluster fol-
lowed by the current gear.
To obtain maximum acceleration, for
passing maneuvers, etc., during
operation in the manual mode, use the
kickdown or downshift manually.<
Shifting from M/S to the selector-lever
positions P, R and N is only possible by
going through D.
Possible displays
P R N D SD M1 M2 M3 M4 M5
Malfunctions
If the indicator lamp lights up, there
is a function fault in the transmis-
sion system.
While it will remain still possible to move
the selector lever to any desired position,
the transmission will revert to operation in
its default mode with only a limited number
of forward gears.
Avoid high loads and drive to the nearest
BMW Sports Activity Vehicle Center.
Never work in the engine compart-
ment with any of the forward or
reverse gears engaged, as the vehicle
could start to move.<
Information on jump-starting and towing
starts on page 108.
Turn signal indicators/
headlamp flasher
1High beams Ð blue indicator lamp
2Headlamp flasher Ð blue indicator lamp
3Turn signal indicators Ð green indicator
accompanied by periodic clicking
sound from the relay
If the flashing indicator lamp and the
clicking from the relay are both faster
than normal, this indicates that one of the
turn signal indicator bulbs is defective.<
Signaling briefly
Press the lever up to but not beyond the
resistance point. It then returns to the cen-
ter position when released.
Washer/wiper system/Rain
sensor*
0Wipers retracted
1Intermittent or rain sensor operation
2Normal wipe
3Fast wipe
4Brief wipe

Reference
At a glance
Controls
Driving tips
Mobility
57
Lamps
Parking lamps/low beams
Parking lamps
The front, rear and side vehicle
lighting is switched on. You can use
the parking lamps for parking. For
lighting on one side for parking as an addi-
tional feature, refer to page 58.
Low beams
When you switch on the ignition
with the headlamps on, the head-
lamps go out and only the parking
lamps remain on.
Lamp defective
The indicator lamp lights up:
At least one bulb of the exterior
lighting on the vehicle is defective.
Replacing the bulbs, refer to page 99.
Pathway lighting
When you activate the headlamp flasher
after parking the vehicle and switching off
the lamps, the low beams will come on for
a brief period.
You may also have this function deac-
tivated if you wish.<
Lights on warning
If you turn the ignition key to position 0, an
acoustic signal sounds when you open the
driver's door for a few seconds to remind
you that the light has not yet been switched
off
.
Daytime driving lamps*
You can leave the light switch in the second
position: all external lamps go out when
you switch off the ignition.
Always observe all applicable laws govern-
ing the use of daytime driving lamps.
You can switch on the parking lamps when
needed using the standard procedure
described under Parking lamps.
You can have the daytime driving
lamp circuit activated on your vehi-
cle.<
Automatic headlamp control*
When you set the switch to this
position, the system activates and
switches on and off the low beams
in response to changes in ambient light
conditions, for instance, in tunnels, at dawn
and dusk, and in rain and snow.
Following automatic activation the
vehicle's external lighting remains on
when you switch on the fog lamps.<
Automatic headlamp control cannot
serve as a substitute for the driver's
judgment in determining when the vehicle
lamps should be switched on. For example,
the system cannot detect fog. To avoid
safety risks, you should always switch on
the lamps manually under these condi-
tions.<
You can have the sensitivity of the
headlamp control adjusted.<
Adaptive Head Light*
The concept
Adaptive Head Light is a variable headlamp
control system that enables dynamic illumi-
nation of the road surface. Depending on
the steering angle and other assumptions,
the light from the headlamp follows the
course of the road.

Reference
At a glance
Controls
Driving tips
Mobility
99
Replacing components
Onboard tool kit
The onboard tool kit is located in a com-
partment on the left under the cargo area.
Replacing wiper blades
Front
1.Move the wiper to a fold-out position,
refer to page 42
2.Lift the wiper arm and press the secur-
ing spring, refer to arrow
3.Pull the wiper blade off toward the
wiper arm
4.Insert the new blade and snap it into
place.
Fold the wipers back down onto the
windshield before you turn the igni-
tion key to position 1 or 2 again. If you do
not, they could be damaged.<
Rear
1.Lift the wiper arm
2.Pull off the wiper blade, refer to arrow
3.Insert a new wiper blade.
Lamps and bulbs
The lamps and bulbs make essential contri-
butions to the safety of your vehicle. There-
fore, comply fully with the following instruc-
tions during bulb replacement. If you are
not familiar with the specified procedures,
BMW recommends having the replace-
ments carried out at your BMW Sports
Activity Vehicle Center.
Never touch the glass of new bulbs
with your bare fingers, as even minute
amounts of contamination will burn into the
bulb's surface and reduce its service life.
To install, use a clean cloth, napkin etc. or
hold the bulb by its metal socket.<
A replacement bulb set is available from
your BMW Sports Activity Vehicle Center.
To prevent short circuits, before
working on any electrical system,
equipment or accessory you should always
switch it off and disconnect the cable from
the battery's negative terminal before start-
ing.
To avoid possible injury or equipment dam-
age when changing bulbs, observe any
instructions provided by the bulb manufac-
turer.<

Replacing components
100 When maintaining the headlamps,
please comply with the instructions in
the separate Caring for your vehicle bro-
chure.<
Halogen low beams
H7 bulb, 55 Watts
Always wear gloves and eye protec-
tion Ð the atmosphere within the bulb
is pressurized. Failure to observe this pre-
caution can lead to personal injury should
the bulb be damaged.<
Driver's side
1.Apply the screwdriver from the on-
board tool kit and pull off the lamp
cover
Caution when handling the screw-
driver, as otherwise personal
injury can occur or the vehicle can be
damaged.<
2.Press the bulb holder downward and
remove
3.Remove the bulb, mount a new bulb
4.Apply the bulb holder with the lower
edge to the bracket and press it in until
the lamp base locks in place.
Front passenger side
Before replacing the bulb, remove the res-
ervoir for the windshield washing system
from the bracket. To do so, loosen the bolt,
refer to arrow, and place the reservoir to
one side.
Bear in mind that the windshield
washing system reservoir is heavy. If
you do not, injuries or damage to the vehi-
cle can occur.<
For bulb replacement procedure, refer to
Driver's side.
Halogen high beams
H7 bulb, 55 Watts
Always wear gloves and eye protec-
tion Ð the atmosphere within the bulb
is pressurized. Failure to observe this pre-
caution can lead to personal injury should
the bulb be damaged.<
Driver's side
1.Open the clip and remove the lamp
cover
2.Press the bulb holder downward and
remove, refer to Low beams
3.Pull off the lamp base; fit a new lamp
base

Reference
At a glance
Controls
Driving tips
Mobility
101
4.Apply the lamp base with the lower
edge to the bracket and press it in until
the lamp base locks in place.
Make sure that the cover does not fall
into the engine compartment, as oth-
erwise the vehicle can be damaged or
other road users can be endangered.<
Front passenger side
Before replacing the bulb, remove the res-
ervoir for the windshield washing system
from the bracket. To do so, loosen the bolt,
refer to arrow, and place the reservoir to
one side.
Bear in mind that the windshield
washing system reservoir is heavy. If
you do not, injuries or damage to the vehi-
cle can occur.<
For bulb replacement procedure, refer to
Driver's side.
Xenon lamps*
The service life of these bulbs is very long
and the probability of a failure is very low,
provided that they are not switched on and
off an unusual number of times. If one of
these bulbs should nevertheless fail, it is
possible to continue driving with great cau-
tion using the fog lamps, provided traffic
laws in your area do not prohibit this.
To avoid risk of potentially fatal inju-
ries: owing to the extremely high volt-
ages at which these units operate, service
work should always be entrusted to quali-
fied personnel.<
Parking and standing lamps
5 Watt bulb
In case of a defect, please contact your
BMW Sports Activity Vehicle Center.
Turn signal indicator, front
21 Watt bulb
Access to the turn signal indicator is at the
edge of the lamp unit, refer to arrow.
Make sure that the lamp base does
not fall into the engine compartment,
as otherwise the vehicle can be damaged
or other road users can be endangered.<
1.Turn the lamp base and remove it
2.Replace the bulb
3.Insert the lamp base. If it does not snap
in place immediately, turn the lamp
base until it does.
Side-mounted turn signal indicators
5 Watt bulb
1.Use finger pressure against the rear
end of the lamp, refer to arrow, to press
it forward for removal
2.Apply gentle pressure to the bulb while
turning it to the left and pull it out
3.Install in the opposite order.

Replacing components
102
Front fog lamps
H11 bulb, 55 Watts
Always wear gloves and eye protec-
tion Ð the atmosphere within the bulb
is pressurized. Failure to observe this pre-
caution can lead to personal injury should
the bulb be damaged.<
1.Pull the cover in front of the fog lamp
forward
2.Loosen the screws, refer to arrow, and
pull out the headlamp
3.Turn the lamp base at the back of the
headlamp to the left and remove it
4.Replace the bulb.
Tail lamps
21 Watt bulb
1Turn signal indicator
2Backup lamps
3Rear lamp
4Rear lamp/brake lamp
Replacing tail lamps
1.Open the flap in the side panel, refer to
page 72
2.Lift the side panel if necessary
3.To release the plug-in connection of the
cable, press the spring, refer to arrow 1
4.To remove the back panel of the lamp,
release the retainer, refer to arrow 2
5.Apply gentle pressure to the bulb fitting
while turning it to the left for removal
and replacement
6.Install in the opposite order.
Lamps in the tailgate are defective:
Please contact your BMW Sports Activity
Vehicle Center.
License plate lamp
10 Watt bulb
1.Press the lamp out to the side with a
screwdriver
2.Remove the lamp and replace the bulb.

Reference
At a glance
Controls
Driving tips
Mobility
103
Tailgate lamp
5 Watt bulb
1.Pull off the bulb holder
2.Replace the bulb.
Light-emitting diodes LEDs
Light-emitting diodes installed behind
translucent lenses serve as the light source
for many of the controls and displays in
your vehicle. These light-emitting diodes,
which operate using a concept similar to
that applied in conventional lasers, are offi-
cially designated as Class 1 light-emitting
diodes.
Do not remove the covers, and never
stare into the unfiltered light for sev-
eral hours, as irritation of the retina could
result.<
Changing a wheel
Safety precautions to observe in the
event of a flat tire and during all tire
changes:
Park the vehicle as far as possible from
passing traffic. Park on a firm, flat, surface.
Switch on the hazard warning flashers.
Lock the steering wheel in straight-ahead
setting of the wheels. Set the handbrake
and engage first gear, reverse gear or
selector-lever position P.
All passengers should be outside the vehi-
cle and well away from your immediate
working area, behind a guardrail, for
instance.
If a warning triangle or portable hazard
warning lamp is required, set it up on the
roadside at an appropriate distance from
the rear of the vehicle. Comply with all safety guidelines and regulations.
Change the wheel only on a level, firm sur-
face which is not slippery. The vehicle or
the jack could slip to the side if you attempt
to raise the vehicle on a soft or slippery sur-
face such as snow, ice, tiles, etc.
Position the jack on a firm support surface.
Do not use a wooden block or similar
object as a support base for the jack, as
this would prevent it from extending to its
full support height and reduce its load-car-
rying capacity.
To avoid serious or fatal injury: never lie
under the vehicle, and never start the
engine while it is supported by the jack.<
What you will need
Open tailgate and raise or remove floor
cover, refer to page 72.
1Vehicle jack
2Chock
3Lug wrench
In order to avoid rattling noises later, note
the position of the tools when you remove
them and return them to their original posi-
tion when you are through using them.
Compact wheel
The compact wheel is located under the
cargo area on the floor of the vehicle.

Reference
At a glance
Controls
Driving tips
Mobility
119
Everything from A to Z
Index
A
A/C operation
Ð air conditioner 60
Ð automatic climate
control 63
ABS Antilock Brake
System 50
Ð indicator lamp 50
Accessories 6
Activated-charcoal filter 65
Adaptive Head Light 57
Adding engine oil 95
Adjusting seats 27
Ð electric 29
Ð mechanical 28
Air, drying, refer to A/C
operation 61, 64
Airbags 54
Ð deactivating 34
Ð indicator lamp 55
Ð sitting safely 27
Air circulation, refer to
Recirculated-air
mode 61, 64
Air conditioner 60, 63
Air distribution
Ð air conditioner 61
Ð automatic climate
control 64
Airing, refer to
Ventilation 61, 65
Air outlets, refer to
Ventilation 61, 65
Air pressure, refer to Tire
inflation pressure 86
Air supply
Ð air conditioner 61
Ð automatic climate
control 64
Air vents, refer to
Ventilation 61, 65
AKI, refer to Fuel
specifications 85Alarm system 24
Ð avoiding unintentional
alarms 25
Anchorages 73
Antifreeze
Ð coolant 95
Ð washer fluid 94
Antifreeze protection
Ð coolant 95
Anti-theft alarm system 18
Ð refer to Alarm system 24
Anti-trapping mechanism
Ð panorama glass roof 24
Ð power windows 22
Approved engine oils 95
Approved gross vehicle
weight 116
Armrest 68
Ð front 68
Ð rear 68
Artificial leather, refer to
Caring for your vehicle
brochure
Ashtray 69
Ð front 69
Ð rear 69
AUC Automatic
recirculated-air
control 64
Automatic
Ð air distribution 64
Ð air supply 64
Automatic car wash, refer
to Caring for your vehicle
brochure
Automatic climate
control 63
Automatic cruise control 43
Automatic curb monitor 32
Automatic headlamp
control 57
Automatic program, refer to
automatic air-
distribution 64Automatic rear window
cleaning 43
Automatic recirculated-air
control AUC 64
Automatic transmission
Ð malfunction 41
Automatic transmission
with Steptronic 39
Ð indicator lamp 41
Ð interlock 37
Ð selector lever interlock 40
Ð shiftlock 40
Average fuel
consumption 48
Average speed 48
Avoiding unintentional
alarms 25
Axle load, permitted 116
B
Backrests, refer to
Adjusting seats 28
Backup lamps 39
Ð replacing bulbs 102
Bad roads 80
Bar, towing 109
Batteries, disposal 106
Battery 105
Ð indicator lamp 12, 105
Ð jump-starting 108
Belts, refer to Safety
belts 30
Beverage holders 67
Black ice, refer to Ice
warning 47
Blower
Ð air conditioner 61
Ð automatic climate
control 64
BMW maintenance
system 97
BMW sports seat 28
Bore, refer to Engine
data 114