2004 BMW X3 3.0I tec

Opening and closing
24 If the glass roof and sliding panel are
closed:
Press the switch once.<
Anti-trapping mechanism
If the glass roof and sliding panel encoun-
ter resistance when closing from roughly
one third of the roof opening or when clos-
ing from the raised position, the closing
action is interrupted and the glass roof and
sliding panel reopen a little.
Despite the anti-trapping mechanism
you should always inspect the roof's
travel path prior to closing it, as the safety
system might fail to detect certain kinds of
obstructions, such as very thin objects, and
the window would continue closing.
The anti-trapping mechanism for closing
the panorama glass roof is deactivated if
the switch is pressed beyond the resis-
tance point and held there. The closing
action is interrupted when you release the
switch.<
Following interruptions in electrical
power supply
Following interruptions in electrical power,
for instance, when the battery is discon-
nected, it is possible that the glass roof will
extend to its tilt-up position, but fail to
respond to other commands. For initializa-
tion, please contact your BMW Sports
Activity Vehicle Center.
Manual operation
In the event of an electrical malfunction,
you can operate the glass roof manually:1.Pull the cover downward
2.Insert the Allen key from the compart-
ment beneath the cargo area floor, refer
to page 103, in the proper opening and
turn the panorama glass roof in the
desired direction. Direction of rotation
for closing, refer to arrow.
Alarm system*
The concept
The vehicle alarm system responds:
>When a door, the hood, or the tailgate is
opened
>To movement in the vehicle's interior Ð
interior motion sensor
>To variations in the vehicle tilt angle
such as occur during attempts to steal
the wheels or tow the vehicle
>To interruption of battery voltage.
The system responds to unauthorized vehi-
cle entry and attempted theft by simulta-
neously activating:
>An acoustic alarm, which lasts for a
period of approx. 30 seconds
>The hazard warning flashers for approx.
5 minutes

Reference
At a glance
Controls
Driving tips
Mobility
25
>The high beams, which flash on and off
in the same rhythm.
Arming and disarming the alarm
system
When the vehicle is locked or unlocked
with the key or the remote control, the
alarm system is also simultaneously armed
or disarmed.
If the alarm system has been properly
armed, the hazard warning flashers light up
once.
You can have different acknowledg-
ment signals set to confirm arming
and disarming.<
You can also open the tailgate with the sys-
tem armed using the button on the
remote control, refer to page 19. When you
close the tailgate, the system is rearmed.<
Switching off the alarm
>Unlock the vehicle using the remote
control, refer to page 19
>Turn the ignition key to position 1.
Indicator lamp displays
>The indicator lamp below the interior
rearview mirror flashes continuously:
the system is armed
>The indicator lamp flashes during arm-
ing: door(s), the hood or tailgate are not
completely closed. Even if you do not
close the alerted area, the system
begins to monitor the remaining areas,
and the indicator lamp flashes continu-
ously after 10 seconds. However, the
interior motion sensor is not activated >If the indicator lamp goes out when the
system is disarmed: no manipulation or
attempted intrusions have been
detected in the period since the system
was armed
>If the indicator lamp flashes for 10 sec-
onds after the system is disarmed: an
attempted entry has been detected in
the period since the system was armed.
Following triggering of an alarm, the indica-
tor lamp will flash continuously.
Avoiding unintentional alarms
The tilt alarm sensor and interior motion
sensor may be switched off at the same
time. You can do this to prevent a false
alarm from being triggered in garages with
elevator ramps, for instance, or when the
vehicle is transported by trailer or train:
Lock twice:
>Press the button on the remote
control twice consecutively
>Lock using the door lock twice.
The indicator lamp lights up briefly and
then flashes continuously. The tilt alarm
sensor and the interior motion sensor are
deactivated as long as the system is
armed.
If you wish, the tilt alarm sensor and
interior motion sensor are perma-
nently switched off. You can have this set
at your BMW Sports Activity Vehicle Cen-
ter.<
Interior motion sensor
In order for the interior motion sensor to
function properly, the windows and pan-
orama glass roof must be completely
closed.
However, be sure to switch off the interior
motion sensor Ð refer to Avoiding uninten-
tional alarms Ð when you
>leave children or animals in the vehicle
>the windows or panorama glass roof
are to remain open.
The tilt alarm sensor and interior
motion sensor are switched off inad-

Reference
At a glance
Controls
Driving tips
Mobility
27
Adjustments
Sitting safely
The ideal sitting position can make a vital
contribution to relaxed driving that is as
fatigue-free as possible. The sitting posi-
tion plays an important role together with
the safety belts and airbags in providing
occupants with maximum levels of passive
safety in an accident. Therefore, observe
the following instructions, as otherwise the
protective function of the safety systems
may be impaired.
For additional information on transporting
children safely, refer to page 34.
Sitting safely with airbags
Always maintain an adequate dis-
tance between yourself and the air-
bags. Always hold the steering wheel by
its rim with hands at the 9 o'clock and
3 o'clock positions, to minimize the risk of
injuries to your hands and arms in the event
of airbag deployment.
No one and nothing is to come between the
airbags and the seat occupant.
Do not use the cover of the front airbag on
the front passenger side as a storage area.
Make sure that the front passenger is cor-
rectly seated, i.e. feet or legs not resting on
the instrument panel, as otherwise leg inju-
ries can result if the knee and front airbag is
triggered.
Never let an occupant's head rest near or
on a side airbag because the inflating air-
bag could cause a serious or fatal injury.<
Even if you adhere to all the instructions
injuries resulting from contact with airbags
cannot be fully excluded, depending on the
circumstances. The ignition and inflation
noise may provoke a mild Ð usually tempo-
rary Ð hearing loss in extremely sensitive
individuals.
For airbag locations and additional infor-
mation on airbags, refer to page 54.
Sitting safely with safety belts
Even though there is an airbag, wear a
safety belt every time you get in the vehi-
cle. Although airbags enhance safety by
providing added protection, they are not a
substitute for safety belts.
Your vehicle has five seats that are all
equipped with a safety belt.
Occupants should sit upright and be
properly restrained at all times:
infants and small children in appropriate
child-restraint systems; larger children and
adults using the safety belts.
Expectant mothers should always wear
their safety belts, taking care to position
the lap belt against the lower hips, where it
will not exert pressure against the abdomi-
nal area.
Never allow more than one person to wear
a single safety belt. Never allow infants and
small children to ride in a passengers lap.
Do not route the belt across your neck, or
run it across sharp edges. Be sure that the
belt does not become caught or jammed.
Avoid twisting the belt while routing it firmly
across the hips and shoulder. Do not allow
the belt to rest against hard or fragile
objects. Otherwise, in the event of a frontal
impact, a loose lap belt could slide over
your hips, leading to abdominal injury.
Avoid wearing clothing that prevents the
belt from fitting properly and pull the lap
belt periodically to readjust the tension
across your shoulder in order to avoid a
reduction in the retention effect of the
safety belt.<
For fastening safety belts, refer to page 30.
Seats
Note before adjusting
Never try to adjust your seat while
operating the vehicle. The seat could
respond with unexpected movement, and

Adjustments
28 the ensuing loss of vehicle control could
lead to an accident.
Especially on the passenger's side, do not
incline the backrest too far to the rear while
the vehicle is being driven, as otherwise
there is a danger in the event of an accident
of sliding under the safety belt, eliminating
the protection normally provided by the
belt.<
Please observe the information on using
safety belts provided on page 30 and the
information on the head restraints on
page 28.
Seat adjustment
To ensure that the safety systems
continue to provide optimized protec-
tion, please observe the adjustment
instructions above.<
1Longitudinal direction
Pull the lever and slide the seat into the
desired position.
After you release the lever, move the
seat forward or backward slightly so
that it engages fully
2Height
Pull the lever and apply weight to or
remove weight from the seat as
required3Backrest angle
Pull the lever and apply weight to or
remove weight from the backrest as
requiredAdjusting the BMW sports seat*
You can also adjust the tilt and the thigh
support:
1Upward tilt:
Pull the lever as many times as required
to set the desired tilt
2Downward tilt:
Press the lever as many times as
required to set the desired tilt
3Thigh support:
Pull the lever and move the thigh sup-
port in the longitudinal direction
Head restraints
Align the head restraints so that their
center is approximately at ear level,
as otherwise the risk of spinal injuries is
increased in the event of an accident.<

Reference
At a glance
Controls
Driving tips
Mobility
29
Adjustments
Height adjustment: pull or press.
To reach the lowest positions, press
button 1.<
To adjust the front head restraint tilt angle:
adjust by tilting.
Removal Ð front
1.Pull the head restraint upward to the
stop
2.Press button 1 and remove the head
restraint.
Installation Ð front
1.Press button 1 and slide the head
restraint into its supports
2.Adjust the head restraint.
Power seat*
To ensure that the safety systems
continue to provide optimal protec-
tion, please observe the adjustment
instructions on page 27.<
1Angle
2Longitudinal direction
3Height
4Backrest angle Set the head restraint manually, refer to left
column.
Lumbar support*
You can also adjust the contours of the
backrest to obtain additional support in the
lumbar region.
The upper hips and spinal column receive
supplementary support to help you main-
tain a relaxed, upright sitting position.
>Press the front or rear of the switch:
Increase or decrease curvature
>Press the upper or lower end of the
switch:
Increase the upper or lower curvature.
Seat and mirror memory*
You can store and select three different
adjustment settings for the driver's seat
and exterior mirrors.
The adjustment of the lumbar support is not
stored in the memory.
Storing
1.Turn the ignition key to position 1 or 2
2.Set the desired seat and exterior mirror
position

Adjustments
30 3.Press MEMORY button:
The indicator lamp in the button lights
up
4.Press the desired memory button 1, 2
or 3:
The indicator lamp goes out.
Selecting a stored setting
Do not call up a position from the
memory while the vehicle is moving,
as otherwise there is a risk of accident from
unexpected seat movement.<
Convenience mode
1.Open the driver's door after unlocking
or turn the ignition key to position 1
2.Briefly press the desired memory but-
ton 1, 2 or 3.
The system immediately cancels the
adjustment procedure when you press
one of the seat adjustment buttons or
use one of the memory buttons.
Safety feature
1.Close the driver's door and turn the
ignition key to position 0 or 2
2.Press the desired memory button 1, 2
or 3 and maintain pressure until the
adjustment process has been com-
pleted.
If you press the
MEMORY button
accidentally:
Press the button a second time Ñ the indi-
cator lamp goes out.<
You can have your vehicle pro-
grammed to automatically dial in your
own individual adjustment settings for the
seat and exterior mirror position whenever
you use your personal remote control to
unlock the vehicle.<
If you make use of this adjustment, be
sure that the footwell behind the
driver's seat is unobstructed before
unlocking the vehicle. If you fail to do so,
any persons, animals or objects behind the
seat could be injured or damaged by a
rearward movement of the seat.<
Heated seats*
The seat cushion and backrest can be
heated when the ignition key is in
position 2.
To call up different temperature levels:
Press the button repeatedly.
To switch off from a higher heat setting:
Press the button and hold it slightly longer.
Safety belts
Even though there is an airbag, wear a
safety belt every time you get in the vehi-
cle. Although airbags enhance safety by
providing added protection, they are not a
substitute for safety belts.
Fastening
Make sure you hear the latch plate engage
in the belt buckle.
Please fasten safety belt warning
lamp:
Lights up for a few seconds or until
safety belts are fastened. Depending on
you vehicle version, a signal
* sounds
simultaneously.

Reference
At a glance
Controls
Driving tips
Mobility
31
Releasing
1.Press the red button in the buckle
2.Hold the belt
3.Guide the belt back into its reel.
The upper shoulder strap's anchorage
point will be in the correct position for seat
occupants of every build if the seat is cor-
rectly adjusted, refer to page 27.
The two rear safety belt buckles integrated
in the rear seat are for passengers sitting
on the left and right. The belt buckle
embossed with the word CENTER is
intended exclusively for use by passengers
riding in the center position.<
Damage to safety belts
If the safety belts are damaged or
stretched in an accident: have the
entire belt system, including the tensioning
mechanisms, replaced at your BMW Sports
Activity Vehicle Center. Have the belt
anchorage points inspected for damage at
the same time. Failure to observe this pre-
caution may prevent the safety belts from
effectively providing optimal protection
when needed. If a child-restraint system
was in the vehicle during an accident, con-
sult the manufacturer's instructions regard-
ing replacement.<
Steering wheel
Adjustments
Do not adjust the steering wheel while
the vehicle is moving. There is a risk
of accident from unexpected movement.< 1.Fold the clamping lever downward
2.Adapt the steering wheel in the longitu-
dinal direction and height of the seat
position
3.Fold the clamping lever back up.
Steering wheel heating*
The button for steering wheel heating is
located in the steering wheel, refer to
page 14.
Steering wheel heating: switching on/off.
The steering wheel heating operates from
ignition key position 2.
Press the button to activate or deactivate
this system.
The indicator lamp within the button lights
up when the steering wheel heating is in
operation.
Mirrors
Adjusting exterior mirrors
1Mirror switch for 4-way adjustment
2Left/right selector switch

Reference
At a glance
Controls
Driving tips
Mobility
35
Installing child-restraint
systems
Before installing any child-restraint system
or child seat, read the following:
Observe the child-restraint system
manufacturer's instructions for instal-
lation and use. Otherwise the degree of
protection can be reduced.
After an accident, have all parts of the rele-
vant vehicle safety belt system checked by
a BMW Sports Activity Vehicle Center and
replaced if necessary.<
Commercially-available child-restraint sys-
tems are designed to be secured with a lap
belt or with the lap belt portion of a combi-
nation lap/shoulder belt. Improperly or
inadequately installed restraint systems
can increase the risk of injury to children.
Always read and follow the instructions that
come with the system.
Child seat security
All of the rear belt retractors and the front
passenger's safety belt can be locked for
mounting and securing child-restraint sys-
tems.
Information regarding this is located near
the buckle latch of each safety belt.
To lock the safety belt
Pull the entire length of the belt from the
belt retractor. Allow the reel to retract the
belt somewhat and engage the buckle,
then tighten the belt against the child-
restraint system. The retraction mechanism
is now locked.
To unlock the safety belt
Release the buckle, remove the child-
restraint system and allow the belt retractor
to reel the belt completely in.
Child-restraint system with tether
strap
If you use a child-restraint system with a
tether strap, three additional tether anchor-
age points have been provided, refer to the
arrows in the illustration. Depending on the
location selected for seating in the rear
passenger area, attach the tether strap to
the corresponding anchorage point to
secure the child-restraint system, as
shown in the illustration below.
Each seating position is fitted with a head
restraint.
Outer seating positions:
Lift the head restraint and pass the tether
strap between the head restraint and the
seat back. It is recommended to readjust
the head restraint into the lowest possible
position.
Center seating position:
The head restraint must be adjusted into
the lowest possible position. Pass the
tether strap over the head restraint.