2004 BMW X3 2.5I lock

Practical interior accessories
68 1.Press the trim piece below the air/heat-
ing vent, arrow 1
2.Insert beverage
3.Adapt the holding arm to the size of the
beverage container, refer to arrow 2.
Rear
A beverage holder is located in the center
armrest at the rear:
Press the button to open.
Glove compartment
Opening
Pull the handle. The lamp inside the glove
compartment comes on.
Closing
Fold the cover up.
To prevent injury in the event of an
accident, close the glove compart-
ment immediately after use.<
Locking
Use one of the master keys. A master key is
also required for unlocking. If you only hand over the spare key,
e.g. in a hotel for valet parking, refer
to page 18, the glove compartment cannot
be accessed.<
Storage compartments
Front center armrest*
The center armrest contains two storage
compartments.
>CD storage compartment:
Press button 1
>Coin and oddments compartment:
Press button 2.
Rear center armrest
A storage compartment holder is located in
the center armrest at the rear:
To open, pull the cover upward.
Storage package*
Your convenience is enhanced by:
>Sliding lashing eyes in luggage com-
partment, refer to page 73
>Floor cover in luggage compartment
that can be used on both sides, refer to
page 72

Reference
At a glance
Controls
Driving tips
Mobility
71
Removing the ski bag
Pull the handle forward and remove the ski
bag upward.
Do not position cargo at the opening.
If you do, it can endanger the passen-
gers during braking or evasive maneu-
vers.<
Cargo area
When loading, observe the information on
page 78.
Folding rear seat back
Reach into the opening and pull forward,
refer to arrow.
When you fold back the backrest, be
sure that the catch engages securely.
The red warning indicator disappears in the
recess when the catch is engaged.<
Ski bag*
To create a flat load area floor, you can
remove the ski bag before folding the rear
seat back and replace it with a cover. You
will find the cover in the cargo area under
the floor cover.
Cargo area cover
Pull the cargo area cover out by the handle
and hook it in the rear holders.
You can carry light objects such as articles
of clothing on the cargo area cover.
Do not place heavy and hard objects
on the cover. If you do so, they could
endanger occupants during braking
maneuvers. Do not allow the cover to snap
back into place, as otherwise it could be
damaged.<
Removal
1.Press the side buttons, refer to arrow 1
2.Pull the cassette towards the rear, refer
to arrow 2.
Installation
Push the cassette forward into the two side
holders until it locks in place.

Practical interior accessories
72
Loading cargo with the rear seat
back folded down
Holders for the cassette are fitted to the
backs of the rear seat backs, refer to
arrow 1.
Guide in the cassette from the right side
until it locks in place, refer to arrow 2. Here,
the cargo area cover must always point in
the direction of travel and the loop of the
partition net must point upward.
You can pull out the partition net and insert
it in the holders in the roof area above.
Partition net*
Pull the partition net by the loop from the
cassette; hold the bar on both sides and
insert in the holder.
Do not allow the partition net to snap
back into place, as otherwise there is
a danger of injury and the partition net
could be damaged.<
Behind the side trim panel
Press the button to open.
Floor cover
Opening
For access to the compact wheel etc.
To open, raise the cover by the handle,
refer to arrow.
If required, you can remove or raise the
floor cover.
Raising
Swing up the floor cover and hook it onto
the handle of the cargo area cover with its
catch.

Refueling
84
Refueling
Fuel filler door
To open and close: press the rear edge of
the fuel filler door.
Manual release
In the event of an electrical defect in the
system, you can release the fuel filler door
manually:
1.Open the cover flap in the luggage
compartment on the right-hand side
panel, refer to page 72
2.Pull the green button.
When handling fuels always observe
any safety guidelines posted at the
service station.<
Simple and environmentally friendly
Put the filler cap in the bracket attached to
the fuel filler door.
When handling fuels, comply with all
of the applicable safety precautions
posted at the service station.<
When refueling, insert the filler nozzle com-
pletely into the filler pipe. Lifting the filler
nozzle during refueling
>results in premature pump shutoff
>can lead to reduced efficiency in the
fuel-vapor recovery system.
The fuel tank is full when the filler nozzle
clicks off the first time.
To close the fuel filler cap
Fit the cap and turn it clockwise until you
clearly hear a click Ð bayonet fitting.
Close the filler cap carefully after refu-
eling, until a click is heard. While clos-
ing, be sure not to squeeze the strap which
is fastened to the cap. A loose or missing
cap will activate the Check Gas Cap
lamp.<
Check Gas Cap
This indicator lamp comes on when
the fuel filler cap is loose or missing.
Close the fuel filler cap tightly as described
above.
Fuel tank capacity
>approx. 17.7 gallons/67 liters, of which
>approx. 2 gallons/8 liters are reserve.

Under the engine hood
92
Under the engine hood
Never attempt to perform any service
or repair operations on your vehicle
without the required professional technical
training. If you are unaware of the regula-
tions that need to be observed, BMW rec-
ommends that you have this work per-
formed at a BMW Sports Activity Vehicle
Center, as otherwise unqualified handling
of parts and materials can lead to safety
risk for vehicle occupants and other road
users.<
Hood
Unlocking
Pull the lever located under the left side of
the instrument cluster.
Opening
Press the release handle and open the
engine hood.
Closing
Let the engine hood fall from approx. 1 ft/
30 cm so that it can be heard to engage.
Observe the same precautions that
apply to all closing operations by
ensuring that the hood's travel range is
clear and unobstructed before allowing the
hood to fall into position.
If you see any signs that the hood is not
completely closed while driving your vehi-
cle, you should stop at once and close it
securely.<

Under the engine hood
96
Checking coolant level and topping
up coolant
Check the coolant level with the engine
cold, approx. 687/206:
1.Turn the cap of the expansion tank
counterclockwise to allow any accumu-
lated pressure to escape, then continue
turning to open
2.The coolant level is correct if the upper
end of the red float bar is at least at the
same height as the top edge of the filler
neck, refer to arrow. The bar end may
only protrude by a maximum of i in/
2 cm, i.e. up to the second mark on the
float bar, refer also to sketch beside the
filler neck
3.If necessary, add coolant. Slowly add
coolant until the correct level is reached
Ð do not overfill.
Always observe all applicable rules
and regulations for environmental
protection when disposing of used anti-
freeze and anticorrosion agents.<
Brake system
Malfunction
Brake fluid
The warning lamp lights up red
despite the handbrake being
released: stop immediately.
The brake fluid in the reservoir has fallen to
below the minimum level. At the same time,
a considerably longer brake pedal travel
may be noticeable. Contact the nearest
BMW Sports Activity Vehicle Center.During continued driving increased
brake pedal pressure may be neces-
sary, and considerably longer braking dis-
tances may result. Please adapt your driv-
ing style accordingly.<
Warning lamp for Canadian models.
Brake pads
The indicator lamp comes on.
The brake pads have reached their
minimum pad thickness. See your
BMW Sports Activity Vehicle Center imme-
diately to have the pads replaced.
For your own safety: use only brake
pads that BMW has released for your
particular vehicle model. As BMW cannot
assess the suitability of other brake pads
for use on your vehicle, we are unable to
assume continued responsibility for the
vehicle's operating safety if non-approved
pads are installed.<
For additional information on the brake sys-
tem, refer to page 77.

Replacing components
100 When maintaining the headlamps,
please comply with the instructions in
the separate Caring for your vehicle bro-
chure.<
Halogen low beams
H7 bulb, 55 Watts
Always wear gloves and eye protec-
tion Ð the atmosphere within the bulb
is pressurized. Failure to observe this pre-
caution can lead to personal injury should
the bulb be damaged.<
Driver's side
1.Apply the screwdriver from the on-
board tool kit and pull off the lamp
cover
Caution when handling the screw-
driver, as otherwise personal
injury can occur or the vehicle can be
damaged.<
2.Press the bulb holder downward and
remove
3.Remove the bulb, mount a new bulb
4.Apply the bulb holder with the lower
edge to the bracket and press it in until
the lamp base locks in place.
Front passenger side
Before replacing the bulb, remove the res-
ervoir for the windshield washing system
from the bracket. To do so, loosen the bolt,
refer to arrow, and place the reservoir to
one side.
Bear in mind that the windshield
washing system reservoir is heavy. If
you do not, injuries or damage to the vehi-
cle can occur.<
For bulb replacement procedure, refer to
Driver's side.
Halogen high beams
H7 bulb, 55 Watts
Always wear gloves and eye protec-
tion Ð the atmosphere within the bulb
is pressurized. Failure to observe this pre-
caution can lead to personal injury should
the bulb be damaged.<
Driver's side
1.Open the clip and remove the lamp
cover
2.Press the bulb holder downward and
remove, refer to Low beams
3.Pull off the lamp base; fit a new lamp
base

Reference
At a glance
Controls
Driving tips
Mobility
101
4.Apply the lamp base with the lower
edge to the bracket and press it in until
the lamp base locks in place.
Make sure that the cover does not fall
into the engine compartment, as oth-
erwise the vehicle can be damaged or
other road users can be endangered.<
Front passenger side
Before replacing the bulb, remove the res-
ervoir for the windshield washing system
from the bracket. To do so, loosen the bolt,
refer to arrow, and place the reservoir to
one side.
Bear in mind that the windshield
washing system reservoir is heavy. If
you do not, injuries or damage to the vehi-
cle can occur.<
For bulb replacement procedure, refer to
Driver's side.
Xenon lamps*
The service life of these bulbs is very long
and the probability of a failure is very low,
provided that they are not switched on and
off an unusual number of times. If one of
these bulbs should nevertheless fail, it is
possible to continue driving with great cau-
tion using the fog lamps, provided traffic
laws in your area do not prohibit this.
To avoid risk of potentially fatal inju-
ries: owing to the extremely high volt-
ages at which these units operate, service
work should always be entrusted to quali-
fied personnel.<
Parking and standing lamps
5 Watt bulb
In case of a defect, please contact your
BMW Sports Activity Vehicle Center.
Turn signal indicator, front
21 Watt bulb
Access to the turn signal indicator is at the
edge of the lamp unit, refer to arrow.
Make sure that the lamp base does
not fall into the engine compartment,
as otherwise the vehicle can be damaged
or other road users can be endangered.<
1.Turn the lamp base and remove it
2.Replace the bulb
3.Insert the lamp base. If it does not snap
in place immediately, turn the lamp
base until it does.
Side-mounted turn signal indicators
5 Watt bulb
1.Use finger pressure against the rear
end of the lamp, refer to arrow, to press
it forward for removal
2.Apply gentle pressure to the bulb while
turning it to the left and pull it out
3.Install in the opposite order.