2004 Acura TL light

The master key fits all the locks on
your vehicle.
The valet key works only in the
ignition and the driver’s door lock.
You can keep the trunk pass-through
cover and the glove box locked when
you leave your vehicle and the valet
key at a parking f acility.Youshouldhavereceivedakey
number tag with your key. You will
need this key number if you ever
have to get a lost key replaced. Use
only an Acura-approved key blank.
These keys contain electronic
circuits that are activated by the
Immobilizer System. They will not
work to start the engine if the
circuits are damaged.
Donotdropthekeysorsetheavy
objects on them. Protect the key f rom direct
sunlight, high temperature, and
high humidity.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
The keys do not contain batteries.
Do not try to take them apart.
Keys
Inst rument s and Cont rols79
KEY
NUMBER
TAG MASTER
KEY
(BLACK)VALET
KEY
(GRAY)

µµ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III).
You can insert or
remove the key only in this position.
To turn the key, you must push the
key in slightly. If your vehicle has an
automatic transmission, the shif t
lever must also be in park. If the f ront wheels are turned, the
anti-thef t lock may make it dif f icult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom ACCESSORY
(I) to ON (II).
Use this position
only to start the engine. The switch
returns to ON (II) when you let go of
the key. You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
the driver’s door. Remove the key to
turn of f the beeper.
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch.
Inst rument s and Cont rols
LOCK (0)
A CCESSORY (I)
ON (II)
ST A RT (III)
Ignition Switch
80
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control.
Remove the key from the
ignition switch only when
parked.

µµµ
µ
Press this button once to
lock all doors. Some exterior lights
will f lash. When you push LOCK
twice within 5 seconds, you will hear
a beep to verify that the doors are
locked and the security system has
set. You cannot lock the doors if any
door is not f ully closed or if the key
is in the ignition switch. Press this button once
to unlock the driver’s door or all the
doors (depending on the Keyless
Memory Setting). Press it twice to
unlock the other doors. Some
exterior lights will f lash twice each
time you press the button.
The ceiling light (if the ceiling light
switch is in the center position) will
come on when you press the
UNLOCK button. If you do not open
anydoorswithin30seconds(or
whatever setting the relock timer is
set to), the light f ades out. If you
relock the doors with the remote
transmitter before 30 seconds have
elapsed, the light will go of f
immediately. Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk with the
remote transmitter if the trunk main
button is turned of f .
Pressthisbuttonfor
about 2 seconds to attract attention:
thehornwillsoundandtheexterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter or turn the ignition
switch to ON (II).
If you unlock the doors with the
remote transmitter, but do not open
anydoorswithin30seconds,the
doors automatically relock and the
security system sets. To change this
setting, ref er to Keyless Memory
Settings on page . 66
Remote Transmitter
Inst rument s and Cont rols
LOCK UNL OCK
T RUNK
PA NIC
85
TRUNK
RELEASE
BUTTON
LOCK
BUTTON
UNLOCK
BUTTON PANIC
BUTTON
LED

Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this sensing. Move the selector switch to L
(driver’s side) or R (passenger’s
side).
Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
1.
2.
Mirrors
Inst rument s and Cont rols
Adjusting the Power Mirrors
91
SELECTOR SWITCH
ADJUSTMENT
SWITCH

When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment switch so you can’t
move a mirror out of position by
accidentally bumping the switch.The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off.
Depending on the position of the
selector switch, the lef t or right side
mirror will pivot downward slightly
when you shif t the transmission into
reverse. In the Lef t position, the lef t
mirror pivots. In the Right position,
the right mirror pivots. This gives
you a better view of that side of the
vehicle while parallel parking. The
mirror returns to its original position
when you take the transmission out
of reverse. To turn this f eature of f ,
leave the switch in the center
position.
Outside mirror positions can be
stored in the driving position
memory system (see page ). 3.
93
Inst rument s and Cont rols
Mirrors
92
HEATED MIRROR BUTTON

Both f ront seats are equipped with
seat heaters. The ignition switch
must be in the ON (II) position to
usethem.PushtheHIsideof the
switch to rapidly heat up the seat.
After the seat reaches a comfortable
temperature, push the LO side of the
switch. This will keep the seat warm.The HI or LO indicator stays on until
youturnitoff bypushingthe
opposite side of the switch lightly.
In HI, the heater turns of f when the
seat gets warm, and turns back on
after the seat’s temperature drops. It
continues to cycle as long as you
leave it set on HI. The HI indicator
stays on as a reminder that you have
the heater on.
In LO, the heater runs continuously.
It does not cycle with temperature
changes.
Follow these precautions whenever
you use the seat heaters:
Use the HI setting only to heat the
seats quickly. Select the LO
setting when the seats f eel warm.
The HI setting draws large
amounts of current f rom the
battery.
Do not use the seat heaters, even
on the LO setting, if the engine is
lef t idling f or an extended period.
Thiscanweakenthebattery,
causing hard starting.
Because of the sensors f or the side
airbag system, there is no heater in
the passenger’s seat-back.
Seat Heaters
Inst rument s and Cont rols96
SEAT HEATERS

µ
The master control panel also has
these f eatures:
To open either f ront
window f ully, push the window
switch f irmly down to the second
detent, then release it. The window
automatically goes down all the way.
To stop the window f rom going all
the way down, pull back on the
window switch briefly.
To close either f ront window f ully,
pull back the window switch f irmly
to the second detent, then release it.
The window automatically goes all
the way up. To stop the window f rom
going all the way up, push down on
the window switch briefly. To open or close either f ront window
partially, push down or pull back on
the window switch lightly to the first
detent and hold it. The window will
stop when you release the switch.
The f ront passenger’s window switch
also has the AUTO f eature.
If either f ront window runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
window, remove the obstacle, then
use the window switch again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it.The MAIN switch controls power to
the passenger’s windows. With this
switch of f , the passenger’s windows
cannot be raised or lowered. The
MAIN switch does not af f ect the
driver’s window. To cancel this
feature, push on the switch again to
getittopopup.KeeptheMAIN
switch of f when you have children in
the vehicle so they do not injure
themselves by operating the
windows unintentionally.
The indicators inside the switches
come on when you turn the ignition
switch to ON (II).
Power Windows
Inst rument s and Cont rols
AUTO
Auto Reverse
98

If the moonroof runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
moonroof , remove the obstacle, then
use the moonroof switch again.
Auto reverse stops sensing when the
moonroof is almost closed. You
should always check that all
passengers and objects are away
f rom the moonroof bef ore closing it.
To close the moonroof f ully, push
the switch firmly forward. The
moonroof automatically close all the
way. To stop the moonroof f rom
closing f ully, pull back the switch
brief ly.
Make sure everyone’s hands are
away f rom the moonroof bef ore
opening or closing it. To open or close the moonroof
partially, pull back or push f orward
the moonroof switch lightly and hold
it. The moonroof will stop when you
release the switch.
To tilt the moonroof , press straight
up on the center of the switch. To
stop the moonroof f rom tilting f ully
open, press the switch a second time. To slide the moonroof open, pull
back the moonroof switch f irmly.
The moonroof automatically opens
all the way. To stop the moonroof
f rom opening f ully, push the switch
f orward brief ly.
Moonroof
Inst rument s and Cont rols
Auto Reverse
101
MOONROOF SWITCH
Opening or closing the
moonroof on someone’s hands
or fingers can cause serious
injury.
Make sure all hands and fingers
are clear of the moonroof
before opening or closing it.