2004 Acura RSX reset

This indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance.For the f irst 8,000 miles (12,800 km)
af ter the Maintenance Required
Indicator is reset, it will come on f or
two seconds when you turn the
ignition switch to ON (II).
Between 8,000 miles (12,800 km)
and 10,000 miles (16,000 km), it will
come on f or two seconds when you
f irst turn the ignition switch to ON
(II), and then f lash f or 10 seconds.
If you exceed 10,000 miles (16,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages and . 159 160
Instrument Panel Indicators
Maintenance Required Indicator
Inst rument s and Cont rols54
MAINTENANCE REQUIRED INDICATOR

Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Acura dealer, reset the indicator as
f ollows.Turn of f the engine.
Press and hold the select/reset
button in the instrument panel,
then turn the ignition switch to
ON (II).
Hold the button for about 10
seconds until the indicator goes
off.This indicator comes on when the
security system is set. See page
f or more inf ormation on the
security system.
1.
2.
3. 114
Instrument Panel Indicators
Security System Indicator
Inst rument s and Cont rols55
SELECT/RESET BUTTON
SECURITY SYSTEM INDICATOR

The odometer shows the total dis-
tance your vehicle has been driven.
It measures miles in U.S. models and
kilometers in Canadian models.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.There are two trip meters: Trip A
and Trip B. The odometer and the
two trip meters use the same display.
Switch between these displays and
the odometer by pressing the Select/
Reset button repeatedly. Each trip
meter works independently, so you
can keep track of two dif f erent
distances.
To reset a trip meter, display it, and
then press and hold the Select/Reset
button until the number resets to
‘‘0.0’’.
Gauges
Odometer
T rip Meter
Inst rument s and Cont rols56
TEMPERATURE GAUGE TACHOMETER SPEEDOMETER FUEL GAUGE
SELECT/RESET BUTTON
ODOMETER/TRIP METER

µIf the driver’s
window runs into any obstacle while
it is closing automatically, it will
reverse direction and then stop. To
close the window, remove the
obstacle, then use the window switch
again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it. If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction will be disabled. The
power window system needs to be
reset af ter reconnecting the battery
or installing the f use.
Start the engine. Push down and
hold the driver’s window switch
until the window is f ully open.
Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
f or a second or two more.
1.
2.
Power Windows
Inst rument s and Cont rols
AUTO REVERSE
79

Playing the Radio
Comf ort and Convenience Feat ures
T ype-S
A ll models except T ype-S
92
AM/FM BUTTON
PWR/VOL KNOB SEEK/SKIP BAR PRESET BUTTONS TUNE/MODE KNOBSTEREO INDICATOR
SCAN INDICATOR
SCAN BUTTON
AUTO SELECT BUTTON
TUNE/MODE KNOB
PRESET BUTTONS SCAN INDICATOR
STEREO INDICATOR
SCAN BUTTON
AUTO SELECT BUTTON FM BUTTON
PWR/VOL KNOB SEEK BUTTONS
AM BUTTON

µ
µ µ´ µ
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pressing the
PWR/VOL knob, or the AM or FM
button. Adjust the volume by turning
the knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is broad-
castinginstereo.Stereo
reproduction on AM is not available.
You can use any of f ive methods to
find radio stations on the selected
band: the
preset buttons, and .Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency.
The SEEK f unction
searches up and down f rom the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
bar or ( )/( ) buttons, then
release it. The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station for about 5 seconds. If you do
nothing, the system will then scan
f or the next strong station and play it
f or 5 seconds. When it plays a station
that you want to listen to, press the
SCAN button again.
CONT INUED
Playing the Radio
Comf ort and Convenience Feat ures
To Play the Radio
To Select a Station
TUNE,SEEK,SCAN, AUTO SELECT TUNE
SEEK
SCAN
93

µµEach preset button can
store one f requency on AM, and two
f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick a preset button, and hold it
until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
stations on FM.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. If you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
Press the A. SEL button. ‘‘A.SEL’’
will f lash in the display, and the
system will go into scan mode f or
several seconds. It stores the
f requencies of six AM stations and
twelve FM stations in the preset
buttons.
You will see a ‘‘0’’ displayed af ter
pressing a preset button if Auto
Select cannot f ind a strong station
f or every preset button. If you do not like the stations Auto
Select has stored, you can store
other f requencies on the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind stations, then
store them in the preset buttons as
described previously.
press the
A. SEL button. This restores the
presets you originally set.
1.
2.
3.
4.
To turn of f Auto Select,
Playing the Radio
Preset
A UT O SEL ECT
Comf ort and Convenience Feat ures94

µ
To load a single CD:
Press and release the Load button.
When the CD number f or an
empty position starts to blink and
the green CD Loaded indicator
comeson,youwillseeLOAdin
the display. Insert the CD into the
CD slot. Insert it only about
half way, the drive will pull it in the
rest of the way.
The system will load the CD, and
begin playing it. If you press the Load button while a
CD is playing, the system will stop
playing that CD and start the loading
sequence. It will then play the CD
just loaded.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate preset
button. Select an empty position (the
CD Loaded indicator is of f ), and
press the preset button f or that
position (1 to 6). The system will
stop playing the current CD and start
the loading sequence. It will then
play the CD just loaded. Select the CD changer by pressing
the CD button. You will see ‘‘Cd’’ in
the display. The system will begin
playing the last selected CD in the
CD changer. You will see the CD and
track numbers displayed.
When that CD ends, the next CD in
the CD changer is loaded and played.
Af ter the last CD f inishes, the
system returns to CD 1.
To select a dif f erent CD, press the
appropriate Preset button (1
6). If
youselectanemptypositioninthe
CD changer, the system will go into
the loading sequence (see page ).
You can use the SKIP buttons while
a CD is playing to select passages
and change tracks.
1.
2.
3.
103
Playing a CD, CD Changer
Comf ort and Convenience Feat ures
Operat ion
104