2004 Acura RSX lock

If Honda antif reeze/coolant is not
available, you may use another
major-brand non-silicate coolant as a
temporaryreplacement.Makesureit
is a high-quality coolant
recommended f or aluminum engines.
Continued use of any non-Honda
coolant can result in corrosion,
causing the cooling system to
malf unction or f ail. Have the cooling
system f lushed and ref illed with
Honda antif reeze/coolant as soon as
possible.When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise.
If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
2. 1.
Engine Coolant
Maint enance168
RADIATOR CAP
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.

Clean the hood latch assembly with a
mild cleaner, then lubricate it with a
multipurpose grease. Lubricate all
the moving parts (as shown),
including the pivot. Follow the time
and distance recommendations in
the Maintenance Schedule. If you
are not sure how to clean and grease
the latch, contact your Acura dealer.
Check the level on the side of the
reservoir when the engine is cold.
The f luid should be between the
UPPER LEVEL and LOWER LEVEL.
If not add power steering f luid to the
UPPER LEVEL mark.
Always use Honda Power Steering
Fluid. You may use another power
steering f luid as an emergency
replacement, but have the power
steering system f lushed and ref illed with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently, and have
the system inspected as soon as
possible.
Power Steering Fluid, Hood L atch
Maint enance
Hood L atch
Power Steering Fluid
173
NOTICE:
NOTICE:
UPPER LEVEL
LOWER LEVEL LATCH ASSEMBLY
PIVOTS
T urning the steering wheel to
f ull lef t or right lock and holding it
there can damage the power steering
pump.
Do not spill the power
steering f luid over the body, auto-
tensioner, drive belt and pulleys.
If spilled accidentally, wipe of f any
f luid completely.

Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
Install the rubber seal and make
sure it is right side up; it is marked
‘‘TOP.’’
Push the electrical connector onto
the tabs of the new bulb. Make
sure it locks in place.
(Passenger’s side)
Install the power steering
reservoir on the bracket.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way, and remove the bulb.
If you need to change a headlight
bulb on the driver’s side, remove
the bolt from the battery hold-
down, and caref ully push the
battery toward the windshield to
obtain enough working space.
Pull the battery back to its original
position, then install the bolt in the
hold-down, and tighten it securely. (Driver’s side)
3.
4. 5.
6.
7.
8.
2.
Lights
Maint enance175
BULB
WEATHER
SEAL
HOLD
DOWN WIRE CONNECTOR
Driver’s side

If you need to change a f ront turn
signal bulb on the passenger’s side,
remove the power steering
reservoir f rom the bracket.If you need to change a f ront turn
signal bulb on the driver’s side,
remove the bolt f rom the battery
hold-down, and caref ully push the
battery toward the windshield to
obtain enough working space.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
1.
2.
3.
Lights
Maint enance
Replacing a Front T urn Signal
Bulb
176
Passenger’s side
POWER STEERING RESERVOIR BULB
Driver’s side

Pull the bulb straight out of its
socket.
The f ront parking bulb is next to
the headlight bulb.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Install the new bulb into the
socket.
(Passenger’s side)
Install the power steering
reservoir on the bracket.
(Driver’s side)
Place the battery in its original
position, then install the bolt in the
hold-down, and tighten it securely.
Install the new bulb into the
socket.
3.
4.
5.
1.
2.4.
Replacing a Front Parking Bulb
Lights
Maint enance177
BULB

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Reinstall the high-mount brake
light cover.
Open the hatch.
Remove the high-mount brake
light cover by pivoting it toward
the back of the vehicle.
Remove the socket by turning it
one-quarter turn counterclockwise. Open the hatch. Remove the light
assembly cover by pulling on the
tabontheoutsideedge.
2.
3. 1. 4.
5.
6.
7.
1.
Lights
Maint enance
Replacing Rear Bulbs
Replacing a High-mount Brake
Light Bulb
178
COVER
COVER BULB

Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Install the light assembly cover.
Make sure it locks in place.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms. Remove the socket by turning it
one-quarter turn counterclockwise. Determinewhichof thefivebulbs
is burned out: brake/taillight, turn
signal light, side marker light,
back-up light, or taillight.
2.
3.
4. 5.
6.
7.
Lights
Maint enance179

CONT INUED
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.To replace a blade (f ront or rear):Raise the wiper arm of f the
windshield or rear window. Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
2.
1.
Wiper Blades
Maint enance181
WIPER ARMS
LOCK TAB