2004 Acura RSX ignition

The 6-speed manual transmission
has an electric lockout so you cannot
accidentally shif t f rom Fif th to
Reverse instead of Sixth. If you
cannot shif t to Reverse when the
vehicle is stopped:With the clutch pedal pressed,
move the shift lever to the First/
Second gear side of the Neutral
gate, then shif t to Reverse.If you are still unable to shif t to
Reverse, apply the parking brake
andturntheignitionkeyto
ACCESSORY (I) or LOCK (0).
Press the clutch pedal, and shif t to
Reverse.
With the clutch pedal still pressed,
start the engine.
If you need to use this procedure to
shif t to Reverse, your vehicle may be
developing a problem. Have the
vehicle checked by your Acura
dealer.
1. 2.
3.
4.
5-speed and 6-speed Manual T ransmissions
Reverse Lockout
Driving138

These indicators on the instrument
panel show which position the shif t
lever is in.
The ‘‘D’’ indicator comes on f or a
f ew seconds when you turn the
ignition switch to ON (II). If it
f lashes at any time (in any shif t
position), it indicates a possible
problem in the transmission. Avoid
rapid acceleration, and have the
transmission checked by an Acura
dealer as soon as possible.To shif t f rom any position, move the
shif t lever. You cannot shif t out of
Park when the ignition switch is in
LOCK (0) or ACCESSORY (I)
position.
CONT INUED
To shift from:
PtoR
RtoN
NtoD
DtoD
DtoD DtoNNtoR RtoP Do this:
Press the brake pedal, then
move the shift lever.
Move the lever.
3
3
Shif t L ever Position Indicators Shif ting
Driving
Automatic Transmission
139
SHIFT LEVER

µµµµµ
This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal.
If you have done all of the above and
still cannot move the lever out of
Park, see on
page .
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. The shif t lever must be in
Park bef ore you can remove the key
from the ignition switch. Press the brake
pedal, and move the shif t lever f rom
Park to Reverse. To shif t f rom
Reverse to Neutral, come to a
completestop,andthenshift.
Your vehicle has a reverse lockout so
you cannot accidentally shif t to
Reverse when the vehicle speed
exceeds 5 mph (8 km/h). Use Neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle for any reason. Press on the
brake pedal when you are moving
the shift lever from Neutral to
another gear.
Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear f or acceleration.
This position is simi-
lartoD,exceptonlythefirstthree
gears are selected. Use D when
towing a trailer in hilly terrain, or to
provide engine braking when going
down a steep hill. D can also keep
the transmission f rom cycling third,
f ourth and f if th gears in stop-and-go
driving.
If you cannot shif t to Reverse when
the vehicle is stopped, press the
brake pedal and slowly shift to
Neutral, and then to Reverse.
If there is a problem in the reverse
lockout system, or your vehicle’s
battery is disconnected or goes dead,
you cannot shif t to Reverse. (Ref er
to Shif t Lock Release on page ).
144
144
3
3
Automatic Transmission
Park (P)
Shif t L ock Release Reverse (R)
Neutral (N)
Drive (D)
Drive (D )
3
Driving140

Do this if pushing on the brake pedal
does not shif t the transmission out of
Park:Set the Parking brake.
Make sure the ignition switch is in
the LOCK (0) position.
Put a cloth on the edge of the Shif t
Lock Release slot cover next to
the shif t lever. Using a small f lat-
tipped screwdriver or a metal
f ingernail f ile, caref ully pry on the
edge of the cover. Insert the key in the Shift Lock
Release slot.
Push down on the key while you
move the shift lever out of Park to
Neutral.Remove the key from the shift
lock release slot, then install a new
cover.
Press the brake pedal and restart
the engine.
If you need to use the Shif t Lock
Release, it means your vehicle is
developing a problem. Have it
checked by your Acura dealer.
5. 4.
3.
2. 1.
6.
Automatic Transmission
Driving
Shif t L ock Release
144
SHIFT LOCK
RELEASE SLOT

CONT INUED
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area to stop
that is far away from the traffic lanes.Park the vehicle on f irm, level, and
non-slippery ground. Put the
transmission in Park (automatic)
or Reverse (manual). Apply the
parking brake. If you are towing a
trailer, unhitch the trailer.Turn on the hazard warning lights,
andturntheignitionswitchto
LOCK (0). Have all the
passengers get out of the vehicle
while you change the tire.
Open the hatch. Pull up the f loor
mat and remove the spare tire
cover.
Unscrew the wing bolt.
1. 2.
3.
4.
Changing a Flat T ire
T aking Care of t he Unexpect ed193
TOOL KIT
JACK
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.

Store the tool kit.
Store the wheel cover or center
cap in the cargo area. Make sure it
will not get scratched or damaged.Diagnosing why your engine won’t
start f alls into two areas, depending
on what you hear when you turn the
key to START (III):
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run. When you turn the ignition switch to
START (III), you do not hear the
normal noise of the engine trying to
start. You may hear a clicking sound
or series of clicks, or nothing at all.
Check these things:
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the f loor or the
starter will not operate. With an
automatic transmission, it must be
in Park or Neutral.
Turn the ignition switch to ON (II).
Turn on the headlights and check
their brightness. If the headlights
are very dim or don’t light at all,
the battery is discharged. See on page .
Reinstall the f loor mat and spare
tire cover, then close the hatch.
22.
23.
24.
200
Changing a Flat Tire, If the Engine Won’t Start
T aking Care of t he Unexpect ed
If the Engine Won’t StartNothing Happens or the Starter
Motor Operates Very Slowly
Jump Starting
198
Loose items can fly around the
interior in a crash and could
seriously injure the occupants.
Store the wheel, jack, and tools
securely before driving.

Turn the ignition switch to START
(III). If the headlights do not dim,
check the condition of the f uses. If
thefusesareOK,thereis
probably something wrong with
the electrical circuit f or the
ignition switch or starter motor.
You will need a qualif ied
technician to determine the
problem (see
on page ).In this case, the starter motor’s
speed sounds normal, or even f aster
than normal, when you turn the
ignition switch to START (III), but
the engine does not run.
Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page ).
Are you using the proper starting
procedure? Ref er to on page .
Do you have f uel? Check the f uel
gauge; the low f uel indicator may
not be working. There may be an electrical
problem, such as no power to the
f uel pump. Check all the f uses
(see page ).
If youfindnothingwrong,youwill
need a qualif ied technician to f ind
the problem. See on page .
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of
the battery and terminal
connections (see page ). You
canthentryjumpstartingthe
vehicle from a booster battery
(see page ). 215
200 188 64
135 210
215
If theEngineWon’tStart
T aking Care of t he Unexpect ed
Emergency T owing T he Starter Operates Normally
Starting the
Engine Emergency
Towing
199

Your vehicle has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics f or the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not
set, the test cannot be completed.
If your vehicle’s battery has been
disconnected or gone dead, these
codes are erased. It takes several
days of driving under various
conditions to set the codes again.To check if they are set, turn the
ignition switch to ON (II), without
starting the engine. The Malf unction
Indicator Lamp will come on f or 20
seconds.If itthengoesoff,the
readiness codes are set. If it blinks
f ive times, the readiness codes are
not set. If possible, do not take your
vehicle f or a state emissions test
until the readiness codes are set. See
State Emissions Testing on pages
and .229
228
Malf unction Indicator L amp
T aking Care of t he Unexpect ed
Readiness Code
207