2004 Acura RSX lights

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Reinstall the high-mount brake
light cover.
Open the hatch.
Remove the high-mount brake
light cover by pivoting it toward
the back of the vehicle.
Remove the socket by turning it
one-quarter turn counterclockwise. Open the hatch. Remove the light
assembly cover by pulling on the
tabontheoutsideedge.
2.
3. 1. 4.
5.
6.
7.
1.
Lights
Maint enance
Replacing Rear Bulbs
Replacing a High-mount Brake
Light Bulb
178
COVER
COVER BULB

Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Install the light assembly cover.
Make sure it locks in place.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms. Remove the socket by turning it
one-quarter turn counterclockwise. Determinewhichof thefivebulbs
is burned out: brake/taillight, turn
signal light, side marker light,
back-up light, or taillight.
2.
3.
4. 5.
6.
7.
Lights
Maint enance179

CONT INUED
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area to stop
that is far away from the traffic lanes.Park the vehicle on f irm, level, and
non-slippery ground. Put the
transmission in Park (automatic)
or Reverse (manual). Apply the
parking brake. If you are towing a
trailer, unhitch the trailer.Turn on the hazard warning lights,
andturntheignitionswitchto
LOCK (0). Have all the
passengers get out of the vehicle
while you change the tire.
Open the hatch. Pull up the f loor
mat and remove the spare tire
cover.
Unscrew the wing bolt.
1. 2.
3.
4.
Changing a Flat T ire
T aking Care of t he Unexpect ed193
TOOL KIT
JACK
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.

Store the tool kit.
Store the wheel cover or center
cap in the cargo area. Make sure it
will not get scratched or damaged.Diagnosing why your engine won’t
start f alls into two areas, depending
on what you hear when you turn the
key to START (III):
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run. When you turn the ignition switch to
START (III), you do not hear the
normal noise of the engine trying to
start. You may hear a clicking sound
or series of clicks, or nothing at all.
Check these things:
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the f loor or the
starter will not operate. With an
automatic transmission, it must be
in Park or Neutral.
Turn the ignition switch to ON (II).
Turn on the headlights and check
their brightness. If the headlights
are very dim or don’t light at all,
the battery is discharged. See on page .
Reinstall the f loor mat and spare
tire cover, then close the hatch.
22.
23.
24.
200
Changing a Flat Tire, If the Engine Won’t Start
T aking Care of t he Unexpect ed
If the Engine Won’t StartNothing Happens or the Starter
Motor Operates Very Slowly
Jump Starting
198
Loose items can fly around the
interior in a crash and could
seriously injure the occupants.
Store the wheel, jack, and tools
securely before driving.

Turn the ignition switch to START
(III). If the headlights do not dim,
check the condition of the f uses. If
thefusesareOK,thereis
probably something wrong with
the electrical circuit f or the
ignition switch or starter motor.
You will need a qualif ied
technician to determine the
problem (see
on page ).In this case, the starter motor’s
speed sounds normal, or even f aster
than normal, when you turn the
ignition switch to START (III), but
the engine does not run.
Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page ).
Are you using the proper starting
procedure? Ref er to on page .
Do you have f uel? Check the f uel
gauge; the low f uel indicator may
not be working. There may be an electrical
problem, such as no power to the
f uel pump. Check all the f uses
(see page ).
If youfindnothingwrong,youwill
need a qualif ied technician to f ind
the problem. See on page .
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of
the battery and terminal
connections (see page ). You
canthentryjumpstartingthe
vehicle from a booster battery
(see page ). 215
200 188 64
135 210
215
If theEngineWon’tStart
T aking Care of t he Unexpect ed
Emergency T owing T he Starter Operates Normally
Starting the
Engine Emergency
Towing
199

´´
Although this seems like a simple
procedure, you should take several
precautions.
You cannot start an Acura with an
automatic transmission by pushing
or pulling it. To jump start your vehicle:
Open the hood and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or like ice, do not try
jump starting until it thaws.
Connect one jumper cable to the
positive ( ) terminal on the
battery. Connect the other end to
the positive ( ) terminal on the
booster battery.
Turn of f all the electrical acces-
sories: heater, A/C, audio system,
lights, etc.
Put the transmission in Neutral or
Park, and set the parking brake.
1.
2.
3.
Jump Starting
T aking Care of t he Unexpect ed200
NOTICE:
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery. If a battery sits in extreme
cold, the electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.

CONT INUED
If something electrical in your
vehicle stops working, the first thing
youshouldcheckforisablownfuse.
Determine f rom the chart on pagesand or the diagram on the
fuse box lid, which fuses control that
device. Check those f uses f irst, but
check all the f uses bef ore deciding
that a blown f use is the cause.
Replace any blown f uses, and check
if the device works.
Turn the ignition switch to LOCK
(0). Make sure the headlights and
all other accessories are off.
Remove the cover f rom the f use
box. Check each of the large f uses in
the under-hood f use box by
looking through the top at the wire
inside. Removing these f uses
requires a Phillips-head screw-
driver.Check the smaller f uses in the
under-hood f use box and all the
fuses in the interior fuse box by
pulling out each f use with the f use
puller provided in the interior f use
box.
3.
1.
2. 4.
213 214
Fuses
T aking Care of t he Unexpect ed
Checking and Replacing Fuses
211
FUSE
BLOWN

Î
ÎÎ
ÎÎ
Î
CONT INUED
No. Circuits Protected No.
Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12 Ignition Coil
Laf Heater
Daytime Running Lights
ACG (IG)
Not Used
Power Window Relay
Moonroof
Radio
Rear Wiper
Gauge panel
ABS
Daytime Running Lights 13
14
15
16
17
18
19
20
21
22
23
24
25
SRS
Power Mirror
Bass Speaker
Heated Seats
Fuel Pump
Accessory Power Socket
Turn Signal
Front Wiper
Not Used
Front Passenger’s Power Window
Driver’s Power Window
Not Used
Not Used
Canadian models only
Type-S only
1:
2:
1
1 2
1
Fuse Locations
T aking Care of t he Unexpect ed213
INTERIOR FUSE BOX