2003 YAMAHA YZF-R6 maintenance

PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
6
EAU03884
NOTE:_

The air filter needs more frequent service if you are riding in unusually wet or dusty areas.


Hydraulic brake service
Regularly check and, if necessary, correct the brake fluid level.
Every two years replace the internal components of the brake master cylinders and calipers, and change the brake
fluid.
Replace the brake hoses every four years and if cracked or damaged.
_24
*Cooling systemCheck coolant level and vehicle for coolant leakage.√√√√ √
Change. Every 3 years
25*Front and rear brake
switchesCheck operation.√√√√√ √
26 Moving parts and cablesLubricate.√√√√ √
27*Throttle grip housing
and cableCheck operation and free play.
Adjust the throttle cable free play if necessary.
Lubricate the throttle grip housing and cable.√√√√ √
28*Air induction systemCheck the air cut-off valve, reed valve, and hose for
damage.
Replace any damaged parts if necessary.√√√√ √
29*Muffler and exhaust pipeCheck the screw clamp for looseness.√√√√√
30*Lights, signals and
switchesCheck operation.
Adjust headlight beam.√√√√√ √ NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (×1,000 km)
ANNUAL
CHECK
1 10203040
U5SLE0.book Page 4 Wednesday, September 11, 2002 11:46 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
6
EAU01139
Removing and installing
cowlings and panels The cowlings and panels shown above
need to be removed to perform some
of the maintenance jobs described in
this chapter. Refer to this section each
time a cowling or panel needs to be re-
moved and installed.
EAU04959
Cowlings A and B
To remove one of the cowlingsRemove the bolts, slide the cowling for-
ward (for A) or backward (for B), and
then pull it off as shown.
1. Cowling A
2. Panel A
1. Cowling B
2. Panel B
1. Bolt (× 3)For Cowling A
U5SLE0.book Page 5 Wednesday, September 11, 2002 11:46 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-6
6
1. Bolt (× 8)
2. Cowling ARight side
1. Bolt (× 8)
2. Cowling BLeft side
1. Cowling A
2. Cowling B
U5SLE0.book Page 6 Wednesday, September 11, 2002 11:46 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-7
6To install the cowling
1. Fit the slots and projections at the
rear bottom of each cowling to-
gether, and then slide the cowling
into place.
2. Place the cowling in the original
position, and then install the bolts.
NOTE:_ Make sure that the tabs at the front of
each cowling fit side by side as shown
and that all slots and projections fit to-
gether. _
EAU04955
Panels A and B
To remove one of the panelsRemove the bolts, slide the panel for-
ward, and then take it off.
1. Slot (× 2)
2. Projection (× 2)
1. Tab (× 2)
1. Bolt (× 2)
U5SLE0.book Page 7 Wednesday, September 11, 2002 11:46 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
6 To install the panel
1. Fit the tabs on the panel into the
slots and slide it backward.
2. Install the bolts.
EAU01639
Checking the spark plugs The spark plugs are important engine
components, which should be checked
periodically, preferably by a Yamaha
dealer. Since heat and deposits will
cause any spark plug to slowly erode,
they should be removed and checked
in accordance with the periodic mainte-
nance and lubrication chart. In addition,
the condition of the spark plugs can re-
veal the condition of the engine.
The porcelain insulator around the cen-
ter electrode of each spark plug should
be a medium-to-light tan (the ideal col-
or when the motorcycle is ridden nor-
mally), and all spark plugs installed in
the engine should have the same color.
If any spark plug shows a distinctly dif-
ferent color, the engine could be defec-
tive. Do not attempt to diagnose such
problems yourself. Instead, have a
Yamaha dealer check the motorcycle.
If a spark plug shows signs of electrode
erosion and excessive carbon or other
deposits, it should be replaced.
1. Tab (× 2)
2. Slot (× 2)
Specified spark plug:
CR9EK, CR10EK (NGK)
U5SLE0.book Page 8 Wednesday, September 11, 2002 11:46 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
6Before installing a spark plug, the spark
plug gap should be measured with a
wire thickness gauge and, if necessary,
adjusted to specification.
Clean the surface of the spark plug
gasket and its mating surface, and then
wipe off any grime from the spark plug
threads.
NOTE:
@
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible. @
ECA00021
CAUTION:@ Do not use any tools to remove or
install the spark plug cap, otherwise
the ignition coil coupler may get
damaged. The spark plug cap may
be difficult to remove because the
rubber seal on the end of the cap fits
tightly. To remove the spark plug
cap, simply twist it back and forth
while pulling it out; to install it, twist
it back and forth while pushing it in. @
EAU04941
Engine oil and oil filter
cartridge The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter car-
tridge replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart.
To check the engine oil level
1. Place the motorcycle on a level
surface and hold it in an upright
position.NOTE:_ Make sure that the motorcycle is posi-
tioned straight up when checking the oil
level. A slight tilt to the side can result in
a false reading. _2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Wait a few minutes until the oil set-
tles.
a. Spark plug gapSpark plug gap:
0.6–0.7 mm
Tightening torque:
Spark plug:
12.5 Nm (1.25 m·kgf)
U5SLE0.book Page 9 Wednesday, September 11, 2002 11:46 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
6 4. Remove the engine oil dipstick
and wipe it clean, insert it back into
the hole (without screwing it in),
and then remove it again to check
the oil level.
NOTE:_ The engine oil should be between the
minimum and maximum level marks. _
5. If the engine oil is at or below the
minimum level mark, remove the
oil filler cap, and then add suffi-
cient oil of the recommended type
to raise it to the correct level.
6. Insert and tighten the engine oil
dipstick, and then install and tight-
en the oil filler cap.To change the engine oil (with or
without oil filter cartridge replace-
ment)
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
1. Engine oil dipstick
2. Maximum level mark
3. Minimum level markRight side
1. Engine oil filler cap
U5SLE0.book Page 10 Wednesday, September 11, 2002 11:46 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
63. Remove the engine oil filler cap
and drain bolt to drain the oil from
the crankcase.
NOTE:_ Skip steps 4–10 if the oil filter cartridge
is not being replaced. _
4. Remove the coolant reservoir cov-
er by removing the bolts.
5. Remove cowling B. (See page 6-5
for cowling removal and installa-
tion procedures.)6. Remove the oil filter cartridge with
an oil filter wrench.
NOTE:_ An oil filter wrench is available at a
Yamaha dealer. _
1. Engine oil drain boltLeft side
1. Coolant reservoir cover
2. Bolt (× 2)
1. Oil filter wrench
2. Oil filter cartridge
U5SLE0.book Page 11 Wednesday, September 11, 2002 11:46 AM