2003 YAMAHA YZ450F diagram

2 - 20
SPEC

LUBRICATION DIAGRAMS
1
Camshaft
2
Connecting rod
3
Oil cleaner element
4
Crankshaft
5
Main axle
6
Drive axle
7
Oil delivery pipe
1
2
3
4
5
67

2 - 21
SPEC

CABLE ROUTING DIAGRAM
EC240000
CABLE ROUTING DIAGRAM
1
Fuel tank breather hose
2
Hot starter cable
3
Radiator hose 4
4
Cylinder head breather hose
5
Radiator hose 1
6
Oil tank breather hose
7
Hose guide
8
Brake hose
9
“ENGINE STOP” button lead
0
Clamp
A
Sub wire harness
B
TPS (throttle position sen-
sor) lead
C
Neutral switch lead
D
Oil hose
E
Radiator breather hose
F
CDI magneto lead
G
Carburetor breather hose
H
Overflow hose
Å
Pass the fuel tank breather hose
between the handlebar and ten-
sion bar, then insert its end into
the hole of the number plate.
ı
Pass the hot starter cable
between the cylinder head
breather hose, oil tank breather
hose and ignition coil, then on
the outside of the left engine
bracket.
Ç
Pass the cylinder head breather
hose on the outside of the radia-
tor hose 1 and on the inside of the
radiator pipe (radiator hose 4).
Î
Fit the brake hose into the
guides on the protector.
‰
Fasten the “ENGINE STOP”
button lead and sub wire har-
ness to the frame with a plastic
locking tie and cut off the tie
end.
ÏFasten the sub wire harness
and hot starter cable to the
frame at the white tape for the
sub wire harness with a plastic
locking tie and cut off the tie
end.
ÌFasten the sub wire harness to
the frame with a plastic locking
tie and cut off the tie end.
C
9
0
A
0
0
0
0
0
B
C
D
0 0 E 0 F 0
1
2 8
7
6
5
4
3GHG9A
D
E
C
B
A
A
C
BB
Ç ÎÅ
ıØ
˜ ˆ
Ò
Ô ÈÌ Ó Ì Ï ‰ ‰
∏
*
*

2 - 22
SPECCABLE ROUTING DIAGRAM
ÓPass the sub wire harness
between the engine brackets.
ÈMake sure that the TPS lead
coupler does not go outside the
chassis.
ÔFasten the TPS lead to the
frame with a plastic band.
Fasten the neutral switch lead
and oil hose together with a
plastic locking tie and cut off
the tie end.
ÒFasten the neutral switch lead
to the frame with a plastic
band.
˜Fasten the neutral switch lead,
CDI magneto lead and radiator
breather hose to the frame with
a plastic band.ˆPass the neutral switch lead,
CDI magneto lead and radiator
breather hose between the
radiator and frame.
ØFasten the neutral switch lead
and CDI magneto lead to the
cable guide with a plastic lock-
ing tie and cut off the tie end.
∏Pass the carburetor breather
hoses and overflow hose so
that all there hoses do not con-
tact the rear shock absorber.*Decompression cable (sup-
plied for Europe and optional
for other destinations)
Pass the decompression cable
under the middle radiator
mounting boss and on the out-
side of the neutral switch lead,
CDI magneto lead and radiator
breather hose.
C
9
0
A
0
0
0
0
0
B
C
D
0 0 E 0 F 0
1
2 8
7
6
5
4
3GHG9A
D
E
C
B
A
A
C
BB
Ç ÎÅ
ıØ
˜ ˆ
Ò
Ô ÈÌ Ó Ì Ï ‰ ‰
∏
*
*

2 - 23
SPECCABLE ROUTING DIAGRAM
1Cable holder
2CDI unit
3Hot starter cable
4Clutch cable
5Throttle cable (return)
6Throttle cable (pull)
7Ignition coil
8Radiator breather hose
9Radiator hose 4
0Cylinder head breather
hose
ACDI unit bracket
BCDI unit bandÅFasten the grommet of the clutch
cable with the cable holder.
ıPass the hot starter cable, clutch
cable and throttle cables through
the cable guides.
ÇPass the hot starter cable over the
top radiator mounting boss.
ÎPass the hot starter cable, clutch
cable and throttle cables between
the radiator and frame, then over
the middle radiator mounting
boss.
‰Pass the clutch cable and throttle
cables on the outside of the igni-
tion coil.
ÏPass the radiator breather hose at
the rear of the radiator, on the left
of the chassis, and then between
the frame and radiator hose 4.ÌInsert the CDI unit band over the
CDI unit bracket as far as possi-
ble.
ÓFirst install the CDI unit and CDI
unit band to the CDI unit bracket,
then the CDI unit bracket to the
frame.
0
8
92
BA
3
4
5
6
712 ÏÓÌ
ı
Ç
Î
‰ ÅB
A
A
B

2 - 24
SPECCABLE ROUTING DIAGRAM
1Master cylinder
2Brake hose holder
3Brake hoseÅInstall the brake hose so that its
pipe portion directs as shown and
lightly touches the projection on
the caliper.
ıPass the brake hose into the
brake hose holders.
ÇIf the brake hose contacts the
spring (rear shock absorber), cor-
rect its twist.
ÎInstall the brake hose so that its
pipe portion directs as shown and
lightly touches the projection on
the master cylinder.

2 - 25
SPECCABLE ROUTING DIAGRAM
1Throttle cable
2Fuel tank breather hose
3Clamp
4Clutch cable
5Hot starter cable
6“ENGINE STOP” button lead
7Brake hose
8Hose guideÅFasten the “ENGINE STOP” but-
ton lead to the handlebar with the
plastic band.
ıPass the brake hose in front of the
number plate.
ÇPass the hot starter cable, clutch
cable and throttle cables through
the cable guide.
*Decompression cable (supplied
for Europe and optional for other
destinations)
1
23
4
5
6
7
83
6 Å
Çı
40˚±10˚
A
A
*

4 - 18
ENGCARBURETOR
15. Install:
Jet needle 1
Collar 2
Spring 3
Needle holder 4
Throttle valve plate 5
To throttle valve 6.
5
6
1
2
3
4
16. Install:
Throttle valve assembly 1
Screw (throttle shaft) 2
NOTE:
Install the valve lever rollers 3 into the slits a
of the throttle valve.
17. Install:
O-ring 1
Valve lever housing cover 2
Bolt (valve lever housing cover) 3
18. Install:
Carburetor breather hose 1
Refer to “CABLE ROUTING DIAGRAM”
section in the CHAPTER 2.

4 - 79
ENG
MAGNETO CDI
CDI-SCHWUNGRADMAGNETZÜNDER
4. Anschließen:
CDI-Schwungradmagnetzünder-Kabel
Siehe unter “KABELFÜHRUNG” im KA-
PITEL 2.
5. Montieren:
Dichtung [Kurbelgehäusedeckel (links)]
Kurbelgehäusedeckel (links) 1
Halterung (Zylinderkopf-Entlüftungs-
schlauch) 2
Schraube [Kurbelgehäusedeckel (links)]
HINWEIS:
Die Schrauben stufenweise über Kreuz fest-
ziehen.
New
T R..10 Nm (1,0 m · kg)
4. Connecter:
Fil de magnéto CDI
Se référer au paragraphe “DIAGRAMME
DE CHEMINEMENT DE CABLE” au
CHAPITRE 2.
5. Monter:
Joint [couvercle de carter (gauche)]
Couvercle de carter (gauche) 1
Support de flexible (reniflard de culasse) 2
Boulon [couvercle de carter (gauche)]
N.B.:
Serrer les vis par étapes dans un ordre entrecroisé.
New
T R..10 Nm (1,0 m · kg, 7,2 ft · lb)