2003 YAMAHA YBR125 clock

Fuel tank cap

#TO OPEN:
Insert the key and turn it 1/4 turn clockwise. The lock will
be released and the cap can be opened.
TO CLOSE:
Push the tank cap into position with the key inserted. To
remove the key, turn it counterclockwise to the original
position.
Be sure the cap is properly installed and locked in place
before riding the motorcycle.
WARNING:
Fuel tank cap

#TO OPEN:
Insert the key and turn it 1/4 turn clockwise. The lock will
be released and the cap can be opened.
TO CLOSE:
Push the tank cap into position with the key inserted. To
remove the key, turn it counterclockwise to the original
position.
Be sure the cap is properly installed and locked in place
before riding the motorcycle.
WARNING:


1. Push 2. Release 3. Turn
LOCK
OFF (PUSH)
Steering lock
The steering is locked when the main switch is turned to
“LOCK”. To lock the steering, turn the handlebars all the
way to the left. With the key at “OFF” position, push it into
the main switch and release it, turn it counterclockwise to
“LOCK”, and remove the key. To release the lock, turn the
key to “OFF”.
Never turn the key to “LOCK” position when the
motorcycle is moving.
WARNING:


1. Push 2. Release 3. Turn
LOCK
OFF (PUSH)
Steering lock
The steering is locked when the main switch is turned to
“LOCK”. To lock the steering, turn the handlebars all the
way to the left. With the key at “OFF” position, push it into
the main switch and release it, turn it counterclockwise to
“LOCK”, and remove the key. To release the lock, turn the
key to “OFF”.
Never turn the key to “LOCK” position when the
motorcycle is moving.
WARNING:

Insert the key and turn it 1/4 clockwise. Pull the cover
towards yourself
to release the fitting pin, and then, pull it
forward .
To reinstall, reverse the removal procedures.


Remove the key nad then pull the cover towards yourself


to release the fitting pin, and then, pull it forward .
To reinstall, reverse the removal procedures.
Side covers
1. Pull 2. Pull forward 1. Pull 2. Pull forward
Insert the key and turn it 1/4 clockwise. Pull the cover
towards yourself

to release the fitting pin, and then, pull it
forward .
To reinstall, reverse the removal procedures.


Remove the key nad then pull the cover towards yourself


to release the fitting pin, and then, pull it forward .
To reinstall, reverse the removal procedures.
Side covers
1. Pull 2. Pull forward 1. Pull 2. Pull forward

6-30
1
1
1. Screw
Headlight bulb replacementIf the headlight bulb burns out, replace the bulb as follows:
1. Remove the screws. 2. Loosen the bulb connectors and remove the rubber cover.
3. Turn the bulb socket counterclockwise and remove the
bulb.
Keep flammable products and your hands away from the
bulb while it is on, as it is hot. Do not touch the bulb until it
cools down
1. Rubber cover
CAUTION:
6-30
1
1
1. Screw
Headlight bulb replacement
If the headlight bulb burns out, replace the bulb as follows:
1. Remove the screws. 2. Loosen the bulb connectors and remove the rubber cover.
3. Turn the bulb socket counterclockwise and remove the
bulb.
Keep flammable products and your hands away from the
bulb while it is on, as it is hot. Do not touch the bulb until it
cools down
1. Rubber cover
CAUTION:

6-32
Turn signal bulb replacement
1. Remove the screws and the lens.
2. Push the bulb inward and turn it counterclockwise.
3. Place a new bulb in the socket.
4. Install the lens and the screws.
Do not over-tighten the screws as the lens may break.
Taillight bulb replacement
1. Remove the lens.
2. Push the bulb inward and turn it counterclockwise.
3. Place a new bulb in the socket.
4. Install the lens.
CAUTION:
6-32
Turn signal bulb replacement
1. Remove the screws and the lens.
2. Push the bulb inward and turn it counterclockwise.
3. Place a new bulb in the socket.
4. Install the lens and the screws.
Do not over-tighten the screws as the lens may break.
Taillight bulb replacement
1. Remove the lens.
2. Push the bulb inward and turn it counterclockwise.
3. Place a new bulb in the socket.
4. Install the lens.
CAUTION: