2003 YAMAHA TDM 900 set clock

3-5
INSTRUMENT AND CONTROL FUNCTIONS
3
NOTE:
After resetting the fuel reserve trip-
meter, the display will return to
“TRIP 1”, unless a different mode had
been previously selected; in that
case, the display automatically
returns to the prior mode.
Fuel gauge
The fuel gauge indicates the amount
of fuel in the fuel tank. The display
segments of the fuel gauge disap-
pear towards “E” (Empty) as the fuel
level decreases. When only one seg-
ment is left near “E”, refuel as soon
as possible.Self-diagnosis device
This model is equipped with a self-
diagnosis device for various electrical
circuits.
If any of those circuits are defective,
the odometer/tripmeter will indicate a
two-digit error code (e.g., 11, 12, 13).
If the odometer/tripmeter indicates
such an error code, note the code
number, and then have a Yamaha
dealer check the motorcycle.
ECA00120
cC
If the odometer/tripmeter indicates
an error code, the motorcycle
should be checked as soon as
possible in order to avoid engine
damage.
EAU04938
Tachometer unitTachometer unitThe electric tachometer allows the
rider to monitor the engine speed and
keep it within the ideal power range.
When the key is turned to “ON”, the
tachometer needle will move to
9,500 r/min and back to zero r/min in
order to test the electrical circuit.
1. Tachometer
2. Tachometer red zone
3. Clock
5PS-28199-E1 8/29/02 9:16 AM Page 18

3-6
INSTRUMENT AND CONTROL FUNCTIONS
3
NOTE:
8After setting the clock, be sure to
push the “SELECT” button
before turning the key to “OFF”,
otherwise the clock will not be
set.
8When the key is turned to “OFF”,
the clock display will remain on
for 48 hours and then go off to
prevent the battery from dis-
charging.EC000003
cC
Do not operate the engine in the
tachometer red zone.
Red zone: 8,000 r/min and above
This tachometer unit is equipped with
a clock.
To set the clock:
1. Push both the “SELECT” and
“RESET” buttons for at least two
seconds.
2. When the hour digits start flash-
ing, push the “RESET” button to
set the hours.
3. Push the “SELECT” button to
change the minutes.
4. When the minute digits start
flashing, push the “RESET” but-
ton to set the minutes.
5. Push the “SELECT” button to
start the clock.
EAU04939
Coolant temperature gaugeCoolant temperature gaugeWith the key in the “ON” position, the
coolant temperature gauge indicates
the temperature of the coolant. When
the key is turned to “ON”, the coolant
temperature gauge needle will move
to “H” and back to “C” in order to test
the electrical circuit. The coolant tem-
perature varies with changes in the
weather and engine load. If the nee-
dle reaches or enters the red zone,
stop the motorcycle and let the
engine cool. (See page 6-45 for fur-
ther instructions.)
1. Coolant temperature gauge
2. Coolant temperature red zone
5PS-28199-E1 8/29/02 9:16 AM Page 19

3-10
INSTRUMENT AND CONTROL FUNCTIONS
3 To adjust the distance between the
brake lever and the handlebar grip,
turn the adjusting dial while holding
the lever pushed away from the han-
dlebar grip. Make sure that the
appropriate setting on the adjusting
dial is aligned with the arrow mark on
the brake lever.
EAU00162
Brake pedalBrake pedalThe brake pedal is on the right side
of the motorcycle. To apply the rear
brake, press down on the brake
pedal.
1. Brake pedal
EAU03232
Fuel tank capFuel tank cap
To open the fuel tank cap
Open the fuel tank cap lock cover,
insert the key into the lock, and then
turn it 1/8 turn clockwise. The lock will
be released and the fuel tank cap can
be opened.
To close the fuel tank cap
1. Push the fuel tank cap into posi-
tion with the key inserted in the
lock.
1a
1. Fuel tank cap lock cover
a. Unlock.
5PS-28199-E1 8/29/02 9:16 AM Page 23