2003 YAMAHA SLIDER 50 lights

EAU00027
INSTRUMENT AND CONTROL FUNCTIONS
Main switch / steering lock .................................................................. 3-1
Indicator and warning lights ................................................................ 3-2
Speedometer unit ................................................................................ 3-3
Fuel gauge .......................................................................................... 3-3
Handlebar switches ............................................................................. 3-4
Front brake lever ................................................................................. 3-4
Rear brake lever ................................................................................. 3-5
Fuel and 2-stroke engine oil tank caps ............................................... 3-5
Fuel ..................................................................................................... 3-6
2-stroke engine oil ............................................................................... 3-7
Catalytic converter .............................................................................. 3-7
Starter (choke) lever ........................................................................... 3-7
Kickstarter ........................................................................................... 3-8
Seat ..................................................................................................... 3-8
Luggage hook ..................................................................................... 3-8
Anti-theft device housing ..................................................................... 3-9
3

INSTRUMENT AND CONTROL FUNCTIONS
31
23
ZAUM0181
EAU03034
Indicator and warning lights
EAU00057
Turn signal indicator light “”
This indicator light flashes when the
turn signal switch is pushed to the left
or right.
1. Turn signal indicator light “”
2. High beam indicator light “
”
3. Oil level warning light “”
EAU00063
High beam indicator light “”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU02958
Oil level warning light “”
This warning light comes on when the
key is in the “
*
” position or when the
oil level in the 2-stroke engine oil tank
is low during operation. If the warning
light comes on during operation, stop
immediately and fill the oil tank with
Yamalube 2 or equivalent 2-stroke
engine oil of either JASO grade "FC"
or ISO grades "EG-C" or "EG-D". The
warning light should go off after the 2-
stroke engine oil tank has been refilled.
NOTE :
If the warning light does not come on
when the key is in the “
*
” position or
does not go off after the 2-stroke engine
oil tank has been refilled, have a
Yamaha dealer check the electrical cir-
cuit.
3-2
EC000000
Do not operate the scooter until you
know that the engine oil level is
sufficient.

INSTRUMENT AND CONTROL FUNCTIONS
312
3ZAUM01421ZAUM0473
1
ZAUM0084
1. Horn switch “ ”
2. Turn signal switch “
”
3. Dimmer switch “,”1. Start switch “
” 1. Front brake lever
EAU00118
Handlebar switches
EAU00125
Turn signal switch “”
To signal a right-hand turn, push this
switch to the right. To signal a left-hand
turn, push this switch to the left. When
released, the switch returns to the
center position. To cancel the turn si-
gnal lights, push the switch in after it
has returned to the center position.
EAU00129
Horn switch “”
Press this switch to sound the horn.
EAU03888
Dimmer switch “,”
Set this switch to “
” for the high beam
and to “
” for the low beam.
EAUM0063
Start switch “”
Push this switch while applying the front
or rear brake to crank the engine with
the starter.
EC000005
See page 5-1 for starting instruc-
tions prior to starting the engine.
EAU03882
Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the
handlebar grip.
3-4

4
PRE-OPERATION CHECKS
ITEM CHECKS PAGE
NOTE :
Pre-operation checks should be made each time the scooter is used. Such an inspection can be accomplished in a very
short time; and the added safety it assures is more than worth the time involved.
EWA00033
If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating
the scooter.
4-2 • Check for damage.
Wheels and Tires• Check tire condition and tread depth.
6-9 — 6-11
• Check air pressure.
• Correct if necessary.
Brake levers• Make sure that operation is smooth.
3-4 — 3-5
• Lubricate lever pivoting points if necessary.
Centerstand• Make sure that operation is smooth.
6-15
• Lubricate pivot if necessary.
Chassis-fasteners• Make sure that all nuts, bolts and screws are properly tightened.
—
• Tighten if necessary.
Instruments, lights• Check operation.
3-1 — 3-4, 6-20 — 6-21
signals and switches• Correct if necessary.
Battery• Check fluid level.
6-17
• Fill with distilled water if necessary.

OPERATION AND IMPORTANT RIDING POINTS
5
EAU03093
Tips for reducing fuel
consumption
Fuel consumption depends largely on
your riding style. Consider the following
tips to reduce fuel consumption:
•Thoroughly warm up the engine.
•Avoid high engine speeds during
acceleration.
•Avoid high engine speeds with no
load on the engine.
•Turn the engine off instead of
letting it idle for an extended
length of time (e.g., in traffic jams,
at traffic lights or at railroad
crossings).
EAU00436
Engine break-in
There is never a more important period
in the life of your engine than the period
between 0 and 1,000 km. For this
reason, you should read the following
material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1,000 km. The various parts in the
engine wear and polish themselves to
the correct operating clearances.
During this period, prolonged full-
throttle operation or any condition that
might result in engine overheating must
be avoided.
EAUT0003*
0 - 150 km
Avoid operation above 1/3 throttle. Stop
the engine and let it cool for 5 to 10
minutes after every hour of operation.
Vary the speed of the scooter from time
to time. Do not operate it at one set
throttle position.150 - 500 km
Avoid prolonged operation above 1/2
throttle.
500 - 1,000 km
Avoid cruising speeds in excess of 3/4
throttle.
ECAT0001*
After 1,000 km of operation, be sure
to replace the final transmission oil.
1,000 km and beyond
Avoid prolonged full throttle operation.
Vary speeds occasionally.
EC000049
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.
5-4

PERIODIC MAINTENANCE AND MINOR REPAIR
6
6-4 20 * Front and rear
•Check operation.√√√√√ √
brake switches
21 Moving parts and cables •Lubricate.√√√√ √
22 * Throttle grip housing and•Check operation and free play.
cable•Adjust the throttle cable free play if necessary.√√√√ √
•Lubricate the throttle grip housing and cable.
23 * Lights, signals and •Check operation.
√√√√√ √
switches •Adjust headlight beam.
NO. Item
Check or maintenance job
ODOMETER READING (x 1,000 km)
1ANNUAL
CHECK6121824
EAU03541*
NOTE :
•The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
•Hydraulic brake service
•Regularly check and, if necessary, correct the brake fluid level.
•Every two years change the brake fluid.
•Replace the brake hoses every four years and if cracked or damaged.

SCOOTER CARE AND STORAGE
7
•Do not use high-pressure
washers or steam-jet cleaners
since they cause water
seepage and deterioration in
the following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric
components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
•For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the
windshield. Test the product on
a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing
compound after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea
or on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads.
NOTE :
Salt sprayed on roads in the winter may
remain well into spring.1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA00012
Do not use warm water since it
increases the corrosive action of the
salt.
2. Apply a corrosion protection spray
on all metal, including chrome-
and nickel-plated, surfaces to
prevent corrosion.
7-2

SPECIFICATIONS
8
8-3 Electrical:
Ignition system type C.D.I
Charging system Flywheel magneto
Battery Model GM4-3B, YB4L-B, FB4-B
Voltage/capacity 12 V / 4 Ah
Headlight type:Bulb
Bulbs (voltage/wattage x quantity):
Headlight 12V, 35W/35Wx1
Tail/brake light 12V, 5W/21Wx1
Turn signal light
Front 12V, 10Wx2
Rear 12V, 10Wx2
Meter lights 12V, 1.2Wx2
High beam indicator light 12V, 2Wx1
Turn signal indicator light 12V, 2Wx1
Oil level warning light 12V, 2Wx1
Fuel level warning light 12V, 2Wx1
Fuses:
Main fuse 7A