2003 YAMAHA FJR1300A fuel

MOTORCYCLE CARE AND STORAGE
7-2
7


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.


Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.


For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quali-
ty plastic polishing compound
after washing.
_After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.After riding in the rain, near the sea or
on salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:_ Salt sprayed on roads in the winter may
remain well into spring. _1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
CAUTION:_ Do not use warm water since it in-
creases the corrosive action of the
salt. _2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.
U5JWE2.book Page 2 Wednesday, November 6, 2002 3:32 PM

MOTORCYCLE CARE AND STORAGE
7-4
7
Storage Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
ECA00014
CAUTION:_

Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.


To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
_
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro-
tect the cylinders, piston rings, etc.
from corrosion.a. Remove the spark plug caps
and spark plugs.
b. Pour a teaspoonful of engine
oil into each spark plug bore.
c. Install the spark plug caps onto
the spark plugs, and then place
the spark plugs on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder walls with oil.)
e. Remove the spark plug caps
from the spark plugs, and then
install the spark plugs and the
spark plug caps.
EWA00003
WARNING
_ To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over. _
U5JWE2.book Page 4 Wednesday, November 6, 2002 3:32 PM

8-1
8
EAU01038
8-SPECIFICATIONSSpecifications CS-01E
Model FJR1300/FJR1300A
Dimensions
Overall length 2,195 mm
Overall width 760 mm
Overall height 1,435 mm
Seat height 805 mm
Wheelbase 1,515 mm
Ground clearance 135 mm
Minimum turning radius 3,100 mm
Basic weight (with oil and full
fuel tank)
FJR1300 275 kg
FJR1300A 282 kg
Engine
Engine type Liquid-cooled 4-stroke, DOHC
Cylinder arrangement Forward-inclined parallel
4-cylinder
Displacement 1,298 cm
3
Bore × stroke 79.0 × 66.2 mm
Compression ratio 10.8:1
Starting system Electric starter
Lubrication system Wet sumpEngine oil
Ty p e
Recommended engine oil
classification API Service SE, SF, SG or
higher
Quantity
Without oil filter cartridge
replacement 3.8 L
With oil filter car tridge
replacement 4 L
Total amount (dry engine) 4.9 L
-20 -10 0
10 20 30
40
50 ˚C
SAE 15W-40SAE 20W-40SAE 10W-40
CAUTION:In order to prevent clutch slippage (since the engine oil also
lubricates the clutch), do not mix any chemical additives. Do
not use oils with a diesel specification of “CD” or oils of a
higher quality than specified. In addition, do not use oils la-
beled “ENERGY CONSERVING II” or higher.
U5JWE2.book Page 1 Wednesday, November 6, 2002 3:32 PM

SPECIFICATIONS
8-2
8
Final gear oil
Type Shaft drive gear oil
(Part No.: 9079E-SH001-00)
Quantity 0.2 L
Cooling system capacity
(total amount)
3.3 L
Air filterDry element
Fuel
Type REGULAR UNLEADED
GASOLINE ONLY
Fuel tank capacity 25 L
Fuel reserve amount 5 L
Electronic Fuel Injection system
Model INP-732/4
Manufacturer NIPPON INJECTOR
Spark plug
Manufacturer/model NGK / CR8E or
DENSO / U24ESR-N
Gap 0.7–0.8 mm
Clutch typeWet, multiple-disc
Transmission
Primary reduction system Helical gear
Primary reduction ratio 1.563
Secondary reduction system Shaft drive
Secondary reduction ratio 2.773Transmission type Constant-mesh 5-speed
Operation Left foot
Gear ratio
1st 2.529
2nd 1.773
3rd 1.348
4th 1.077
5th 0.929
Chassis
Frame type Diamond
Caster angle 26°
Trail 109 mm
Tires
Front
Type Tubeless tire
Size 120/70 ZR17 M/C (58 W)
Manufacturer/model Metzeler / MEZ4J FRONT
Bridgestone / BT020FN
Rear
Type Tubeless tire
Size 180/55 ZR17 M/C (73 W)
Manufacturer/model Metzeler / MEZ4J
Bridgestone / BT020RN
U5JWE2.book Page 2 Wednesday, November 6, 2002 3:32 PM

SPECIFICATIONS
8-4
8
Battery
Model GT14B-4
Voltage, capacity 12 V, 12 Ah
Headlight typeHalogen bulb
Bulb voltage, wattage × quantity
Headlight 12 V, 60/55 W × 2
Tail/brake light 12 V, 5/21 W × 2
Turn signal light 12 V, 21 W × 4
Auxiliary light 12 V, 5 W × 2
Meter lighting 14 V, 1.12 W × 4
Neutral indicator light 14 V, 1.12 W × 1
High beam indicator light 14 V, 1.12 W × 1
Turn signal indicator light 14 V, 1.4 W × 2
Engine trouble warning light 14 V, 1.12 W × 1
Oil level warning light 14 V, 1.12 W × 1
ABS warning light
(For FJR1300A only) 14 V, 1.12 W × 1
Immobilizer system indicator
light L.E.D.
Fuses
Main fuse 50 A
Electronic fuel injection fuse 15 A
Headlight fuse 25 A
Signaling system fuse 15 A
Radiator fan fuse 15 AIgnition fuse 10 A
Odometer, clock and
immobilizer system fuse
(backup fuse) 10 A
Parking lighting fuse 10 A
Hazard fuse 7.5 A
Windshield motor fuse 2 A
Anti-lock Brake System
fuse (For FJR1300A only) 7.5 A
E_5jw_Spec.fm Page 4 Monday, November 11, 2002 10:01 AM

INDEXAABS (For FJR1300A only)...................... 3-13
ABS warning light
(For FJR1300A only) .............................3-5
Accessory box ....................................... 3-19
Air filter element, cleaning ...................... 6-15
Anti-theft alarm ........................................3-9
Auxiliary light bulb, replacing .................. 6-35BBattery ................................................... 6-31
Brake and clutch fluid levels,
checking .............................................. 6-23
Brake and clutch fluids, changing........... 6-25
Brake and clutch levers,
checking and lubricating ...................... 6-27
Brake and shift pedals,
checking and lubricating ...................... 6-26
Brake lever............................................. 3-12
Brake light switch (rear), adjusting ......... 6-22
Brake pads, checking............................. 6-22
Brake pedal............................................ 3-12
Brake pedal position, adjusting .............. 6-21CCables, checking and lubricating............ 6-25
Care.........................................................7-1
Catalytic converter ................................. 3-16
Centerstand and sidestand,
checking and lubricating ...................... 6-27
Clutch lever ........................................... 3-11
Clutch lever free play ............................. 6-21
Conversion table ..................................... 8-5
Coolant level, checking .......................... 6-13DDimmer switch ......................................... 3-9EEngine break-in ....................................... 5-3
Engine idling speed, checking ............... 6-16
Engine oil and oil filter cartridge ............... 6-9
Engine stop switch................................. 3-10
Engine trouble warning light .................... 3-5FFinal gear oil .......................................... 6-12
Front fork, adjusting ............................... 3-19
Front fork, checking ............................... 6-29
Fuel ....................................................... 3-15
Fuel consumption, tips for reducing ......... 5-3
Fuel tank breather hose ......................... 3-16
Fuel tank cap ......................................... 3-14
Fuses, replacing .................................... 6-32HHandlebar switches ................................. 3-9
Hazard switch ........................................ 3-10
Headlight bulb, replacing ....................... 6-33
High beam indicator light ......................... 3-5
Horn switch ............................................. 3-9
IIdentification numbers ..............................9-1
Ignition circuit cut-off system ..................3-24
Immobilizer system..................................3-1
Immobilizer system indicator light.............3-4
Indicator and warning lights......................3-4KKey identification number .........................9-1LLocks for optional side cases and
travel trunk ...........................................3-23MMain switch/steering lock .........................3-2
Model label ..............................................9-2
Multi-function display................................3-7NNeutral indicator light ...............................3-5OOil level warning light ...............................3-5PPanels, removing and installing ................6-5
Parking.....................................................5-4
Part locations ...........................................2-1
Pass switch ..............................................3-9
Periodic maintenance and
lubrication chart .....................................6-2
Pre-operation check list ............................4-1
E_5jwIX.fm Page 1 Monday, November 11, 2002 10:01 AM