2003 YAMAHA BEAR TRACKER 250 light

6-11 1. Drive select lever
2. Lock release button
a. Foward
b. Reverse
1. Levier de présélection
2. Bouton de déblocage
a. Marche avant
b. Marche arrière
1. Palanca de selección de gama
2. Botón de desbloqueo
a. Marcha adelante
b. Marcha atrás
EBU00186
Drive select lever operation and reverse
drivingCAUTION:
Before shifting, stop the machine and return
the throttle lever to its closed position. Other-
wise the transmission may be damaged.NOTE:When shifting into reverse, the transmission must
be in first gear.1. Bring the machine to a complete stop and re-
turn the throttle lever to the closed position.
2. Apply the rear brake pedal.
3. Shift the transmission into first gear.
4. While pulling the lock release button, move
the drive select lever toward the rear until it
completely stops.NOTE:When in reverse, the reverse indicator light should
be on. If the light does not come on, ask a Yamaha
dealer to inspect the machine.
U4XE64.book Page 11 Thursday, May 30, 2002 1:49 PM

7-43 1. Lean towards inside of turn.
2. Support your weight on the outer footrest.
1. Se pencher vers l’intérieur du virage.
2. S’appuyer sur le repose-pied externe.
1. Inclínese hacia el interior del giro.
2. Descanse su peso en el descansapie externo.
As you approach a curve, slow down and begin to
turn the handlebars in the desired direction. As
you do so, put your weight on the footboard to the
outside of the turn (opposite your desired direc-
tion) and lean your upper body into the turn. Use
the throttle to maintain an even speed through the
turn. This maneuver will let the wheel on the inside
of the turn slip slightly, allowing the ATV to make
the turn properly.
This procedure should be practiced at slow speed
many times in a large off-road area with no obsta-
cles. If an incorrect technique is used, your ATV
may continue to go straight. If the ATV doesn’t
turn, come to a stop and then practice the proce-
dure again. If the riding surface is slippery or loose,
it may help to position more of your weight over the
front wheels by moving forward on the seat.
Once you have learned this technique you should
be able to perform it at higher speeds or in tighter
curves.
U4XE64.book Page 43 Thursday, May 30, 2002 1:49 PM

7-61
CROSSING A SLOPE
Traversing a sloping surface on your ATV requires
you to properly position your weight to maintain
proper balance. Be sure that you have learned the
basic riding skills on flat ground before attempting
to cross a sloping surface. Avoid slopes with slip-
pery surfaces or rough terrain that may upset your
balance.
As you travel across a slope, lean your body in the
uphill direction. It may be necessary to correct the
steering when riding on loose surfaces by pointing
the front wheels slightly uphill. When riding on
slopes be sure not to make sharp turns either up or
down hill.
U4XE64.book Page 61 Thursday, May 30, 2002 1:49 PM

8-33
1. Air filter element 2. Foam cover
1.Élément du filtre à air 2. Cache en mousse
1. Elemento del filtro de aire 2. Forro de espuma
3. Pull out the air filter element.
4. Separate the foam cover from the air filter el-
ement.
5. Tap the air filter element lightly to remove
most of the dust and dirt. Blow out the re-
maining dirt with compressed air. If the air fil-
ter element is damaged, replace it.
6. Wash the foam cover gently but thoroughly in
water or solvent.
WARNING
When using solvent to clean the foam cover,
always use parts cleaning solvent. Never use
low flash point solvents or gasoline to clean
the foam cover because the engine could
catch fire or explode. 7. Squeeze the excess solvent out of the foam
cover and let it dry.CAUTION:

Do not twist the foam cover when squeez-
ing it.


Do not apply oil to the foam cover.
8. Inspect the foam cover. If damaged, replace
it.
U4XE64.book Page 33 Thursday, May 30, 2002 1:49 PM

8-57 1. Rear brake light switch
2. Adjusting nut
1. Contacteur de feu stop sur frein arrière
2.Écrou de réglage
1. Interruptor de la luz de freno trasero
2. Tuerca de ajuste
EBU00834
Adjusting the rear brake light switch
The rear brake light switch, which is activated by
the brake pedal and brake levers, is properly ad-
justed when the brake light comes on just before
braking takes effect. If necessary, adjust the brake
light switch as follows.
Turn the adjusting nut while holding the rear brake
light switch in place. To make the brake light come
on earlier, turn the adjusting nut in direction
a. To
make the brake light come on later, turn the adjust-
ing nut in direction
b.
U4XE64.book Page 57 Thursday, May 30, 2002 1:49 PM

8-79 1. Headlight cover
1. Cache de phare
1. Carenado del faro
1. Bulb holder cover (× 2) 2. Bulb holder
1. Cache de la fixation d’ampoule (× 2) 2. Fixation d’ampoule
1. Cubierta del portabombilla (× 2) 2. Portabombilla
EBU01071
Replacing a headlight bulb
If a headlight bulb burns out, replace the bulb as
follows.
1. Remove the headlight cover.
2. Remove the bulb holder cover.
3. Turn the bulb holder counterclockwise to re-
move the defective bulb.
WARNING
The headlight bulb is hot when it is on and im-
mediately after it is turned off. Wait for the bulb
to cool before touching or removing it. You can
be burned or a fire could start if the bulb touch-
es something flammable.
U4XE64.book Page 79 Thursday, May 30, 2002 1:49 PM

8-81 1. Adjusting screw (× 2)
1. Vis de réglage (× 2)
1. Tornillo de ajuste (× 2)
4. Put a new bulb into position and secure it in
place with the bulb holder.
5. Install the bulb holder cover and headlight
cover.
6. Adjust the headlight beam if necessary.
EBU01089
Headlight beam adjustmentCAUTION:
It is advisable to have a Yamaha dealer make
this adjustment. To raise the beam, turn the adjusting screw in
direction
a.
To lower the beam, turn the adjusting screw in
direction
b.
U4XE64.book Page 81 Thursday, May 30, 2002 1:49 PM

8-83 1. Storage box 2. Nut (× 2)
1. Compartiment de rangement 2.Écrou (× 2)
1. Caja artículos 2. Tuerca (× 2)
1. Bulb holder
1. Fixation d’ampoule
1. Portabombilla
EBU00945
Tail/brake light bulb replacement
1. Open the storage box. (See page 4-31.)
2. Remove the nuts together with washers.
3. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
U4XE64.book Page 83 Thursday, May 30, 2002 1:49 PM