2003 YAMAHA BANSHEE 350R parking brake

6-25
EBU00212
Parking
When parking, stop the engine and shift into low
gear. Turn the fuel cock to “OFF” and apply the
parking brake.
5FK-9-64-6 4/8/02 1:22 PM Page 26

6-27
EBU00993
Parking on a slope
w
Avoid parking on hills or other inclines.
Parking on a hill or other incline could cause
the ATV to roll out of control, increasing the
chance of an accident. If you must park on
an incline, put the machine in low gear, apply
the parking brake, and block the front and
rear wheels with rocks or other objects.
Do not park the ATV at all on hills that are so
steep you could not walk up them easily.
1. Bring the machine to a stop by applying the
brakes in low gear.
2. Stop the engine and release the clutch
lever.
3. With the front and rear brakes applied, apply
the parking brake and slowly release the
brake pedal.
5FK-9-64-6 4/8/02 1:22 PM Page 28

7-35
Select a large, flat area off-road to become
familiar with your ATV. Make sure that this area
is free of obstacles and other riders. You should
practice control of the throttle, brakes, shifting
procedures, and turning techniques in this area
before trying more difficult terrain. Always avoid
riding on paved surfaces: the ATV is designed
for off-road use only, and handling maneuvers
are more difficult to perform on pavement.
Set the parking brake and follow the instruction
on page 6-3 to start the engine. Once it has
warmed up you are ready to begin riding your
ATV. As you get on the ATV, be sure not to
accidentally move the shift pedal. Remember
that the engine and exhaust pipe will be hot
when riding and afterwards; do not allow skin or
clothing to come in contact with these compo-
nents.
5FK-9-64-7 4/8/02 1:24 PM Page 36

7-37
With the engine idling, pull the clutch lever to dis-
engage the clutch and shift into 1st gear, and
then release the parking brake. Open the throttle
gradually, and at the same time, release the
clutch lever slowly. Once the ATV has attained
adequate speed, release the throttle lever and at
the same time, quickly pull in the clutch lever and
shift into 2nd gear. Open the throttle part way and
gradually release the clutch. Use this same pro-
cedure as you move into the higher gears. Be
sure to coordinate the use of the throttle and shift
pedal properly. If the throttle is applied too
abruptly or if the throttle is not released during
shifting, or if the shift pedal is not released before
applying the throttle, the front wheels may lift off
the ground resulting in a loss of directional con-
trol. Avoid higher speeds until you are thoroughly
familiar with the operation of your ATV.
w
Always open the throttle gradually and
release the clutch lever slowly. Otherwise,
the ATV could wheelie which would increase
the chance of an accident.
5FK-9-64-7 4/8/02 1:24 PM Page 38

7-55
w
Use proper gear and maintain steady speed
when climbing a hill.
If you lose all forward speed:
8Keep weight uphill.
8Apply the brakes.
8Lock the parking brake, after you are
stopped.
If you begin rolling backwards:
8Keep weight uphill.
8Never apply the rear brake while rolling
backwards. Apply the front brake.
When fully stopped, apply the rear brake
as well, and then lock the parking brake.
Dismount on uphill side or to a side if point-
ed straight uphill. Turn the ATV around and
remount, following the procedure described
in the Owner’s Manual.
5FK-9-64-7 4/8/02 1:24 PM Page 56

8-85
EBU00953
Parking brake adjustment
Parking brake adjustment may be required if the
parking brake does not hold properly.
1. Fully loosen the parking brake cable
adjusting bolt locknut and the adjusting bolt
on the clutch lever.
2. Loosen the adjusting bolt locknut and the
adjusting bolt on the rear brake caliper.
3. Turn the adjusting bolt on the clutch lever
so that cable length ais 46–50 mm.
NOTE:
If the cable cannot be adjusted to specification,
consult a Yamaha dealer.
4. Tighten the adjusting bolt locknut on the
clutch lever.
5. Screw in the adjusting bolt on the brake
caliper by hand until it feels tight, then
screw it out 1/8 turn. Tighten the adjusting
bolt locknut to the specified torque.
q
w
1. Locknut 2. Adjusting bolt1. Contre-écrou 2. Boulon de réglage1. Contratuerca 2. Perno de ajuste
a
a. Cable lengtha. Longueur du câblea. Longitud del cable
5FK-9-64-8 4/8/02 1:26 PM Page 86

8-87
cC
When tightening the locknut, hold the adjust-
ing bolt with a wrench so that the adjusting
bolt does not turn together with the locknut.
w
Operating with improperly adjusted brakes
could cause the brakes to malfunction,
resulting in reduced braking performance.
This could increase the chance of a collision
or accident.
After adjusting the parking brake, block the
rear of the machine off the ground and spin
the rear wheels. Check to make sure there is
no brake drag. If brake drag is noticed, per-
form the adjustment again.
qw
1. Ajusting bolt 2. Locknut1. Boulon de réglage 2. Contre-écrou1. Perno de ajuste 2. Contratuerca
Tightening torque:
Locknut:
16 Nm (1.6 m0kgf)
5FK-9-64-8 4/8/02 1:26 PM Page 88