2003 TOYOTA TUNDRA width

[x] Cancel search: width

brake lug pattern alternator belt fuel fill door release remote control key battery

Page 211 of 345

TOYOTA TUNDRA 2003 1.G Owners Manual ’03 TUNDRA_U (L/O 0307)
202
2003 TUNDRA from Jul. ’03 Prod. (OM 34430U)
The “DOT” symbol certifies that the
tire conforms to applicable Federal
Motor Vehicle Safety Standards.
This illustratio

Page 212 of 345

TOYOTA TUNDRA 2003 1.G Owners Manual ’03 TUNDRA_U (L/O 0307)
203
2003 TUNDRA from Jul. ’03 Prod. (OM 34430U)
1. Bead
2. Sidewall
3. Shoulder
4. Tread
5. Belt
6. Inner liner
7. Reinforcing rubber
8. Carcass
9. Rim lines
10.Bead wires

Page 215 of 345

TOYOTA TUNDRA 2003 1.G Owners Manual ’03 TUNDRA_U (L/O 0307)
206
2003 TUNDRA from Jul. ’03 Prod. (OM 34430U)
Production options weight
The combined weight of those installed regular production options weighing
over 2.3 kg (5 lb.) in

Page 303 of 345

TOYOTA TUNDRA 2003 1.G Owners Manual ’03 TUNDRA_U (L/O 0307)
294
2003 TUNDRA from Jul. ’03 Prod. (OM 34430U)
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replace

’03 TUNDRA_U (L/O 0307)
294
2003 TUNDRA from Jul. ’03 Prod. (OM 34430U)
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.
If you fail to replace a damaged wheel,
the tire may slip off the wheel or cause
loss of handling control.
WHEEL SELECTION
When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and offset.
Correct replacement wheels are available
at your Toyota dealer.
A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ability, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis. Replacement with used wheels is not rec-
ommended as they may have been sub-
jected to rough treatment or high mileage
and could fail without warning. Also, bent
wheels which have been straightened may
have structural damage and therefore
should not be used. Never use an inner
tube in a leaking wheel which is designed
for a tubeless tire.
CAUTION
Observe the following instructions.
Otherwise, an accident may occur re-
sulting in death or serious injuries.
Do not use wheels other than the
manufacturer ’s recommended size,
as this may cause dangerous han-
dling characteristics resulting in
loss of control.
Fourwheel drive models:
Do not use wheels of different
brands, sizes and types, as this
may cause dangerous handling
characteristics resulting in loss of
control.
When installing aluminum wheels,
check that the wheel nuts are tight
after driving your vehicle the first 1600
km (1000 miles).
If you have rotated, repaired, or
changed your tires, check that the
wheel nuts are still tight after driving
1600 km (1000 miles).
When using tire chains, be careful not
to damage the aluminum wheels.
Use only the Toyota wheel nuts and
wrench designed for your aluminum
wheels.
When balancing your wheels, use only
Toyota balance weights or equivalent
and a plastic or rubber hammer.
As with any wheel, periodically check
your aluminum wheels for damage. If
damaged, replace immediately.
Replacing wheels
Aluminum wheel precautions

Page 317 of 345

TOYOTA TUNDRA 2003 1.G Owners Manual ’03 TUNDRA_U (L/O 0307)
308
2003 TUNDRA from Jul. ’03 Prod. (OM 34430U)
mm (in.)
TWO−WHEEL DRIVE MODELSFOUR− WHEEL DRIVE MODELS
Standard cab
modelsAccess cab modelsStandard cabmodelsAccess cab

belt air suspension recommended oil child restraint service lock