2003 SUZUKI GRAND VITARA Reverse light switch

YH4
GRAND
VITARA
1
1. Mode control switch coupler
2. A / C switch
3. Indicator lamp
AIR CONDITIONING (OPTIONAL) 1B-45
A / C SWITCH
REMOVAL
1) Disconnect negative (±) cable at battery.
2) If equipped with air bag system, disable air bag system.
Refer to ªDISABLING AIR BAG SYSTEMº in Section 10B.
3) Remove mode control switch (Refer to ªMODE CONTROL
SWITCHº in Section 1A).
INSPECTION
A / C Switch

Press A / C button and check if there is continuity between termi-
nals ªDº and ªGº.

With battery voltage (+) connected to terminal ªKº and (±) to termi-
nal ªDº, press A / C button and check if indicator lamp lights.
INSTALLATION
1) Install in reverse order of removal procedure.
2) If equipped with air bag system, enable air bag system.
Refer to ªENABLING AIR BAG SYSTEMº in Section 10B.

YH4
GRAND
VITARA
1. Back up light switch
2. Exhaust center pipe
1. Ohmmeter
2. Back up light switch or 4WD switch1, (a)
[Type 1]
[Type 2]
MANUAL TRANSMISSION (TYPE 1) 7A-7
3) Replace switch, connect and clamp as they were.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft) (Type 1)
(a): 45 N
.m (4.5 kg-m, 32.5 lb-ft) (Type 2)
4) When back up light switch has been replaced, check switch for
proper function with ignition switch turned ON and gear shifted
to reverse position. Turn OFF switch after checking its function.
INSPECTION OF 4WD SWITCH AND BACK UP LIGHT
SWITCH
1) Undo clamp and disconnect coupler of back up light switch
and / or 4WD switch.
2) Function of back up light switch can be checked as shown in fig-
ure.
There should be conduction at these terminals only when shift
lever is shifted to reverse position.
3) Function of transfer 4WD switch can be checked in the same
manner as back up light switch.
There should be conduction at these terminals when shift lever
is shifted to 4H, and 4L positions.
Upon completion of check, connect coupler and clamp wiring har-
ness as they were.
NOTE:
When replacing switch(es), use care not to let dust enter trans-
mission through switch hole(s).

YH4
GRAND
VITARA
Terminal
Wire ColorSwitch Position
Terminal
Switch Position
Wire Color
HEAD
OFFHI
PASS SMALL
8B-6 LIGHTING SYSTEM
ON-VEHICLE SERVICE
HEADLIGHTS
HEADLIGHT SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
Lighting Switch
ELTH
WGR
OFF
SMALL
HEAD
Dimmer & Passing Switch
EDHLHUHF
W/BR/WRR/B
Passing (PASS)
Low Beam
High Beam (HI)
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
REMOVAL
1) Disconnect negative cable at battery.
2) Remove front grille.
3) Disconnect harness and couplers from headlight assembly.
4) Remove three bolts and pull headlight assembly off vehicle.
INSTALLATION
Reverse removal procedure for installation.
Make sure to follow HEADLIGHT AIMING WITH SCREEN and aim
headlight after installation.

YH4
GRAND
VITARA
LH steering vehicle shown
X-X:Horizontal center line of headlight bulbs
A-A:Vertical center line of left headlight bulb
B-B:Vertical center line of right headlight bulb1. Screen
2. For right / left adjustment
3. For up / down adjustment
(for vehicle without leveling system)
4. For up / down adjustment
(for vehicle with leveling system)
5. Headlight leveling actuatorHOT
SPOT LH. HEADLIGHT RH. HEADLIGHT
LIGHTING SYSTEM 8B-7
BULB REPLACEMENT
WARNING:
Don't touch when the bulb is hot.
1) Disconnect negative cable at battery.
2) Disconnect harness from bulb.
3) Remove socket cover and bulb.
4) Replace bulb and install in reverse removal procedure.
HEADLIGHT AIMING WITH SCREEN
NOTE:

Unless otherwise obligated by local regulations, adjust
headlight aiming according to following procedure.

After replacing headlight, be sure to perform its aiming.

When inspecting and adjusting headlight with leveling sys-
tem, make sure to set the leveling switch to ª0º position with
IG switch ON.
Before adjustment, make sure the following.
a) Place vehicle on a flat surface in front of blank wall as below
ahead of headlight surface.
Clearance ªaº: 10 m (32.8 ft)
b) Adjust air pressure of all tires to a specified value respectively.
c) Bounce vehicle body up and down by hand to stabilize suspen-
sion.
d) Carry out one driver aboard.
Driver's weight: 75 kg (165 lb)
Adjustment
1) Check to see if hot spot (high intensity zone) of each main (low)
beam axis falls as illustrated.
Clearance ªHº: Approx. 130 mm (5.15 in.)
2) If headlight aiming is not set properly, align it to specification by
adjusting aiming screw and aiming gear.

YH4
GRAND
VITARA
1. Meter cluster
2. Hazard switch
Terminal
Wire ColorSwitch Position
LH steering vehicle shown
LIGHTING SYSTEM 8B-9
TURN SIGNAL AND HAZARD WARNING
LIGHTS
TURN SIGNAL SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
TLTBTR
G/RGG/Y
L
N
R
REMOVAL AND INSTALLATION
Refer to Section 3C COMBINATION SWITCH for vehicle without air
bag system and Section 3C1 CONTACT COIL AND COMBINA-
TION SWITCH ASSEMBLY for vehicle with air bag system.
HAZARD SWITCH
REMOVAL
1) Remove meter cluster.
2) Pull hazard switch out of instrument panel.
3) Disconnect coupler from hazard switch.
4) Remove hazard switch.
INSTALLATION
Reverse removal procedure.
INSPECTION
Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace siwtch.

YH4
GRAND
VITARA
8C-12 INSTRUMENTATION / DRIVER INFORMATION
BRAKE AND PARKING BRAKE WARNING
LIGHT
BRAKE FLUID LEVEL SWITCH
INSPECTION
Check switch (1) for continuity.
If check result is not as specified, replace switch (reservoir).
OFF position (float up)
No continuity
ON position (float down)Continuity
PARKING BRAKE SWITCH
INSPECTION
Check switch (1) for continuity.
If check result is not as specified, replace switch.
OFF position
(parking brake lever released)
No continuity
ON position
(parking brake lever pulled up)Continuity
IGNITION KEY REMAINDER (IF EQUIPPED) /
LIGHT REMAINDER WARNING BUZZER
REMOVAL
1) Remove combination meter (1). Refer to COMBINATION ME-
TER in this section.
2) Remove buzzer unit (2) from combination meter.
INSTALLATION
Reverse removal procedure for installation.

YH4
GRAND
VITARA
1. Spot light
2. Head lining
3. Sunvisor assemblies
4. Room light
5. Trim
6. Assist grips
1. Sliding roof motor
2. Mounting screw
1. Motor assy
2. Hole (body)
3. Hole (cam)
9-66 BODY SERVICE
SLIDING ROOF MOTOR / RELAY
REMOVAL
1) Remove head lining, refer to HEAD LINING REMOVAL in this
section.
2) Disconnect coupler and remove sliding roof motor assembly by
removing 3 screws.
CAUTION:
After removing sliding motor assembly, do not move
guide and link.
INSTALLATION
For installation, reverse removal procedure, noting following point.
Before installing, connect coupler and push the CLOSE side of the
slide switch.