2003 SUZUKI GRAND VITARA short

YH4
GRAND
VITARA
8G-16 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
1. Main fuse
2. Main relay
3. ECM / PCM
4. Immobilizer indicator lamp
(Vehicle not equipped with
monitor coupler) For G16 / J20 engine For H25 engine
G16 / J20 Engine
H25 Engine
TABLE C IMMOBILIZER INDICATOR LAMP CHECK
(IMMOBILIZER INDICATOR LAMP REMAINS ON AFTER ENGINE
STARTS)
STEPACTIONYESNO
11) With ignition switch OFF, disconnect
couplers from ECM / PCM.
Does immobilizer indicator lamp turn ON
at ignition switch ON?ª(p)º wire shorted to
ground circuit.Substitute a known-good ECM /
PCM and recheck.

YH4
GRAND
VITARA
8G-18 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
12
3
4
1. Main fuse
2. Main relay
3. Immobilizer
Control Module
4. Coil antenna
5. To ECM / PCM 5 (a)
(f)(k)
(I)
DTC13 NO TRANSPONDER CODE TRANSMITTED OR COIL ANTENNA
OPENED/SHORTED
DESCRIPTION:
Immobilizer Control Module energizes the coil antenna when the ignition switch is ON and reads Transponder code
from the ignition key. When Immobilizer Control Module cannot read Transponder code from the ignition key even
when the coil antenna is energized, this DTC is set.
INSPECTION:
STEPACTIONYESNO
1Does ignition key being used have built-in trans-
ponder? (See Fig. 1)Go to Step 2.Replace ignition key with built-in trans-
ponder and follow ªDIAGNOSTIC
FLOW TABLEº again.
21) Disconnect coil antenna coupler with ignition
switch turned OFF.
2) Is there continuity between coil antenna cou-
pler terminals A and B?
(See Fig. 2)Go to Step 3.Coil antenna open.
3Measure resistance between terminals of coil an-
tenna coupler and body ground. (See Fig. 3)
Is it
(infinity)
?Go to Step 4.Coil antenna shorted to ground.
41) With coil antenna coupler disconnected, dis-
connect Immobilizer Control Module coupler.
2) Measure resistance between coil antenna ter-
minals of Immobilizer Control Module coupler.
(See Fig. 4)
Is it
(infinity)
?Go to Step 5.ª(k)º wire shorted to ª(l)ºwire.
5Measure resistance between terminal A1 of Im-
mobilizer Control Module coupler and body
ground.
(See Fig. 5)
Is it
(infinity)
?Go to Step 6.ª(k)º wire shorted to ground.
6Measure resistance between terminal A2 of Im-
mobilizer Control Module coupler and body
ground. (See Fig. 6)
Is it
(infinity)
?Go to Step 7.ª(I)º wire shorted to ground.
71) Connect coil antenna coupler.
2) Is there continuity between Immobilizer Con-
trol Module coupler terminals A1 and A2?
(See Fig. 7)Go to Step 8.
ª(k)º or ª(I)º wire open.

Poor coil antenna-to-coupler.

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-19
DTC13 NO TRANSPONDER CODE TRANSMITTED OR
COIL ANTENNA OPENED/SHORTED
(CONTINUED)
STEPACTIONYESNO
8Poor A1 or A2 connection.
1) If connections are OK, connect
Immobilizer Control Module
coupler and substitute a known-
good coil antenna.
2) Is DTC 13 also indicated with
ignition switch turned ON?Go to Step 9.Faulty coil antenna.
9Is DTC 13 still indicated even when
another ignition key (with built-in
transponder) for that vehicle used?Substitute a known-good Immobilizer
Control Module and recheck.
NOTE:
After replacing with a known-good
Immobilizer Control Module, register
ECM/Immobilizer Control Module code
in ECM / PCM and Transponder code
and ECM/Immobilizer Control Module
code in Immobilizer Control Module by
performing procedure described in
ªProcedure after Immobilizer Control
Module Replacementº section.Faulty ignition key.
1. Coil antenna
coupler
1
1. Coil antenna
coupler
1
A
B
Fig. 1 for Step 1
Ignition key with built-in
transponder
Fig. 2 for Step 2 Fig. 3 for Step 3
Fig. 4 for Step 4
Fig. 5 for Step 5 Fig. 6 for Step 6
1. Immobilizer Control
Module coupler1
A1
A2
A1
1
1. Immobilizer Control
Module coupler
1. Immobilizer Control
Module couplerA21
Fig. 7 for Step 7
1. Immobilizer Control Module couplerA1
1 A2

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-21
12
3
1. Main fuse
2. Ignition switch
3. Immobilizer
Control Module (g)
A4
DTC22 IGNITION SWITCH CIRCUIT OPEN / SHORT
DESCRIPTION:
Immobilizer Control Module monitors ignition signal when the ignition switch is ON. This DTC is set when no ignition
signal input is detected by Immobilizer Control Module.
INSPECTION:
STEPACTIONYESNO
1Check voltage between Immobilizer
Control Module coupler terminal A4
and body ground with ignition
switch turned ON.
(See Fig.1)
Is it 10 ± 14V?Poor A4 terminal connection.
If connection is OK, substitute a
known-good Immobilizer Control
Module and recheck.
NOTE:
After replacing with a know-good
Immobilizer Control Module,
register ECM/Immobilizer Control
Module code in ECM / PCM and
Transponder code and ECM/
Immobilizer Control Module code
in Immobilizer Control Module by
performing procedure described
in ªProcedure after Immobilizer
Control Module Replacementº
section.ª(g)º wire open or short.
Fig. 1 for Step 1
1
A4
1. Immobilizer Control Module

YH4
GRAND
VITARA
8G-22 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
A812
To SDM (if equipped with AIRBAG)
To data link connector (DLC)1. Immobilizer Control Module
2. ECM / PCM (j) (i)
(i)
(i)
DTC23 NO ECM/IMMOBILIZER CONTROL MODULE CODE TRANSMITTED
FROM ECM/PCM OR DLC CIRCUIT OPENED/SHORTED
DTC83 NO ECM/IMMOBILIZER CONTROL MODULE CODE TRANSMITTED
(P1621) FROM IMMOBILIZER CONTROL MODULE OR DLC CIRCUIT
OPENED/SHORTED
DESCRIPTION
When the ignition switch is ON, Immobilizer Control Module requests ECM / PCM and ECM / PCM requests Immobi-
lizer Control Module to transmit ECM/Immobilizer Control Module code. If ECM/Immobilizer Control Module code
is not transmitted from ECM / PCM or Immobilizer Control Module, Immobilizer Control Module sets DTC23 and
ECM / PCM sets DTC83 (P1621).
INSPECTION:
STEPACTIONYESNO
1Check voltage between
Immobilizer Control Mod-
ule coupler terminal A8
and body ground with igni-
tion switch turned ON.
Is it 4 ± 5V?Go to Step 2.ª(i)º or ª(j)º wire
short.
21) Disconnect ECM /
PCM coupler with igni-
tion switch turned
OFF.
2) Is there continuity be-
tween Immobilizer
Control Module cou-
pler terminal A8 and
Data link connector
terminal of ECM / PCM
coupler? (For posi-
tions of Data link con-
nector terminal of
ECM / PCM coupler,
refer to Section 6E1 or
6E2.)Poor A8 connection (Immobilizer Control Module) or
Poor Data link connector terminal connection (ECM /
PCM). If connections are OK, substitute a known-good
ECM / PCM or Immobilizer Control Module and re-
check.
NOTE :

After replacing with a known-good ECM / PCM,
register ECM/Immobilizer Control Module code
in ECM / PCM by performing procedure de-
scribed in ªProcedure after ECM / PCM Replace-
mentº section.

After replacing with a known-good Immobilizer
Control Module, register ECM/Immobilizer Control
Module code in ECM / PCM and Transponder code
and ECM/Immobilizer Control Module code in Im-
mobilizer Control Module by performing proce-
dure described in ªProcedure after Immobilizer
Control Module Replacementº section.ª(i)º or ª(j)º wire be-
tween Immobilizer
Control Module and
ECM / PCM open.
Fig. 1 for step 1
1
A8
1. Immobilizer Control Module
1. Immobilizer Control Module coupler disconnected1
A8Connect to Data link connector terminal
of ECM / PCM coupler disconnected
Fig. 2 for step 2

YH4
GRAND
VITARA
10B
AIR BAG SYSTEM 10B-1
GENERAL DESCRIPTION10B- 3 . . . . . . . . . . . . .
System Components and Wiring
Location View and Connectors 10B- 4. . . . . . .
System Wiring Diagram 10B- 5. . . . . . . . . . . . . .
DIAGNOSIS10B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Codes 10B- 6. . . . . . . . . . . .
Use of Special Tools 10B- 6. . . . . . . . . . . . . . . . .
Intermittent and Poor Connections 10B- 8. . . . .
Air Bag Diagnostic System Check 10B-10. . . . .
Air bag diagnostic system check
flow table 10B-11. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code (DTC) check 10B-12.
Diagnostic trouble code (DTC)
clearance 10B-13. . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code table 10B-14. . . . . . . .
Table A - ªAIR BAGº warning lamp
comes ªONº steady 10B-16. . . . . . . . . . . . . . .
Table B - ªAIR BAGº warning lamp
does not come ªONº 10B-18. . . . . . . . . . . . . .
Table C - ªAIR BAGº warning lamp
flashes 10B-20. . . . . . . . . . . . . . . . . . . . . . . . . .
Table D - SDM cannot communicate
through the serial data circuit 10B-22. . . . . . . Code 15 - Passenger air bag initiator
circuit resistance high 10B-24. . . . . . . . . . . . .
Code 16 - Passenger air bag initiator
circuit resistance low 10B-26. . . . . . . . . . . . . .
Code 18 - Passenger air bag initiator
circuit short to ground 10B-28. . . . . . . . . . . . .
Code 19 - Passenger air bag initiator
circuit short to power circuit 10B-30. . . . . . . .
Code 21 - Driver air bag initiator
circuit resistance high 10B-32. . . . . . . . . . . . .
Code 22 - Driver air bag initiator
circuit resistance low 10B-34. . . . . . . . . . . . . .
Code 24 - Driver air bag initiator
circuit short to ground 10B-36. . . . . . . . . . . . .
Code 25 - Driver air bag initiator
circuit short to power circuit 10B-38. . . . . . . .
Code 31 - Power source voltage high 10B-40
Code 32 - Power source voltage low 10B-42.
Code 41 - Driver pretensioner initiator
circuit resistance high 10B-44. . . . . . . . . . . . .
Code 45 - Passenger pretensioner
initiator circuit resistance high 10B-44. . . . . .
Code 42 - Driver pretensioner initiator
circuit resistance low 10B-46. . . . . . . . . . . . . .
SECTION 10B
AIR BAG SYSTEM
WARNING:

Service on or around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in this section before performing service on or around the air bag system components or
wiring. Failure to follow WARNINGS could result in unintended activation of the system or could ren-
der the system inoperative. Either of these two conditions may result in severe injury.

The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above condi-
tions are not followed, parts or system damage could result.
CONTENTS

YH4
GRAND
VITARA
10B-2 AIR BAG SYSTEM
Code 46 - Passenger pretensioner
initiator circuit resistance low 10B-46. . . . . . .
Code 43 - Driver pretensioner initiator
circuit short to ground 10B-48. . . . . . . . . . . . .
Code 47 - Passenger pretensioner
initiator circuit short to ground 10B-48. . . . . .
Code 44 - Driver pretensioner initiator
circuit short to power circuit 10B-50. . . . . . . .
Code 48 - Passenger pretensioner
initiator circuit short to power circuit 10B-50.
Code 51 - Frontal crash detected
(System activation command is
outputted) 10B-52. . . . . . . . . . . . . . . . . . . . . . .
Code 61 -ªAIR BAGº warning lamp
circuit failure 10B-53. . . . . . . . . . . . . . . . . . . . .
Code 71 - Internal SDM fault 10B-54. . . . . . . .
ON-VEHICLE SERVICE10B-55 . . . . . . . . . . . . . . .
Service Precautions 10B-55. . . . . . . . . . . . . . . . .
Service and diagnosis 10B-55. . . . . . . . . . . . . .
Disabling air bag system 10B-56. . . . . . . . . . . .
Enabling air bag system 10B-56. . . . . . . . . . . .
Handling and storage 10B-57. . . . . . . . . . . . . .
Disposal 10B-62. . . . . . . . . . . . . . . . . . . . . . . . . .
Repairs and Inspections Required
after an Accident 10B-63. . . . . . . . . . . . . . . . . . .
Accident with deployment
- component replacement 10B-63. . . . . . . . . . Accident with or without deployment
- component inspections 10B-64. . . . . . . . . . .
Driver Air Bag (Inflator) Module 10B-66. . . . . . . .
Contact Coil and Combination Switch
Assembly 10B-66. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Pretensioner 10B-66. . . . . . . . . . . . . . .
ªAIR BAGº Warning Lamp 10B-66. . . . . . . . . . . .
SDM 10B-67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Passenger Air Bag (Inflator) Module 10B-69. . .
AIR BAG (INFLATOR) MODULES
DISPOSAL10B-71 . . . . . . . . . . . . . . . . . . . . . . . . . .
Deployment Outside Vehicle 10B-71. . . . . . . . . .
Deployment Inside Vehicle 10B-78. . . . . . . . . . . .
SEAT BELT PRETENSIONERS
DISPOSAL10B-83 . . . . . . . . . . . . . . . . . . . . . . . . . .
Activation Outside Vehicle 10B-83. . . . . . . . . . . .
Activation Inside Vehicle 10B-89. . . . . . . . . . . . . .
DEPLOYED AIR BAG (INFLATOR)
MODULES DISPOSAL10B-93 . . . . . . . . . . . . .
ACTIVATED SEAT BELT PRETENSIONERS
DISPOSAL10B-94 . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS10B-95 . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS10B-95 . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
WIRE HARNESS COLOR
B : Black
B/W : Black/White
Bl : Blue
Bl/B : Blue/Black
Bl/R : Blue/Red
Br : BrownG : Green
Gr : Gray
G/R : Green/Red
Lg : Lightgreen
P : Pink
V : VioletY : Yellow
Y / G : Yellow/Green
Y/R : Yellow/Red
W : White
W/B : White/Black
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B
4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin
7. To ECM (or PCM), ICM (if equipped) and ABS
controller (if equipped)
8. To data link connector (DLC)
9. ªAIR BAGº monitor coupler
10. SDM
11. Contact coil assembly
12. Driver air bag (inflator) module
13. Driver seat belt pretensioner (if equipped)
14. Passenger air bag (inflator) module
15. Passenger seat belt pretensioner (if equipped)
16. Pretensioner harness (if equipped)
17. Ground for air bag system
TERMINAL
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A13 A11
A12
A14
A15
A16
Passenger air bag (inflator) moduleLow
High
CIRCUIT
Data link connector (DLC)
Low
High
Low
High
Low
High ªAIR BAGº warning lamp
Driver air bag (inflator) module
Diagnosis switch
±±±±±±±±±
Ground
Passenger pretensioner
Driver pretensioner
Ignition switch (power source)±±±±±±±±±
±±±±±±±±±
CONNECTOR ªAº (SDM connector) TERMINAL ARRANGEMENT OF SDM
(VIEWED FROM HARNESS SIDE)
L1
L2Connection detection pin
: Shorting bar
: Air bag harness
ªAº
ªHº : Connector
AIR BAG SYSTEM 10B-5
SYSTEM WIRING DIAGRAM