Page 230 of 801
YH4
GRAND
VITARA
ªAº: Drill hole with approximately
3 mm (0.12 in.) diameter.
REAR SUSPENSION 3E-3
DIAGNOSIS
DIAGNOSIS TABLE
Refer to SECTION 3.
SHOCK ABSORBER CHECK
Inspect for deformation or damage.
Inspect bushings for wear or damage.
Inspect for evidence of oil leakage.
Replace any defective part.
WARNING:
When handling rear shock absorber in which high-pressure
gas is sealed, make sure to observe the following precau-
tions.
1) Don't disassemble it.
2) Don't put it into the fire.
3) Don't store it where it gets hot.
4) Before disposing it, be sure to drill a hole in it where
shown by an arrow in the figure and let gas and oil out.
Lay it down sideways for this work.
5) The gas itself is harmless but it may issue out of the hole
together with chips generated by the drill. Therefore, be
sure to wear goggle.
LOWER ROD, UPPER ROD, LATERAL ROD
CHECK
Inspect for cracks, deformation or damage.
Replace any defective part.
Inspect each bush for wear and breakage. If found defective, re-
place.
AXLE HOUSING AND COIL SPRING CHECK
Inspect for cracks, deformation or damage.
Inspect for evidence of oil leakage at axle housing.
If any, replace defective part.
Page 233 of 801
YH4
GRAND
VITARA
1. Parking brake
cable hanger
2. Cross member
3. Clamp
4. Chassis frame1. Rear axle housing
2. Floor jack
1. Shock absorber
2. Lower bolt
1. Clamp
2. Upper rod
3E-6 REAR SUSPENSION
COIL SPRING
REMOVAL
1) Hoist vehicle and remove rear wheel.
2) Support rear axle housing by using floor jack.
3) Disconnect parking brake cable hanger from chassis frame and
clamp from cross member.
4) Remove shock absorber lower mounting bolt.
5) Remove wheel speed sensor clamps from upper rod and axle
housing, if equipped with ABS.
For right side, remove E-ring for fixing brake pipe from cross
member and disconnect breather hose from axle housing.
6) Lower rear axle housing gradually as far down as where coil
spring can be removed.
7) Remove coil spring.
Page 234 of 801
YH4
GRAND
VITARA
1. Rear axle housing
2. Spring seat
3. Coil spring
4. Stepped part
1. Body center
2. Body outside
1. Body center
2. Body outside 1. Parking brake
cable hanger
2. Cross member
3. Clamp
4. Chassis frame
REAR SUSPENSION 3E-7
INSTALLATION
1) Install coil spring on spring seat of axle housing and then raise
axle housing.
NOTE:
When seating coil spring, mate spring end with stepped
part of rear axle spring seat as shown.
2) Install shock absorber lower bolt. For its proper installing direc-
tion, refer to figure.
Nut should not be tightened.
3) Install wheel speed sensor clamp (if equipped) and E-ring, and
connect breather hose to axle housing.
4) Connect cable hanger to chassis frame and clamp to cross
member. Remove floor jack from axle housing.
5) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
6) Lower hoist and tighten absorber lower nut to specified torque.
Tightening Torque
(b): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
NOTE:
For tightening of lower nut, refer to NOTE given under
SHOCK ABSORBER INSTALLATION in this section.
Page 245 of 801
YH4
GRAND
VITARA
3E-18 REAR SUSPENSION
1. Axle housing
2. Jack
1. Differential carrier
assembly
2. Differential carrier nut
1. Lower rod
2. Lower rod rear
mount nut
3. Shock absorber
1. Lower mount
bolt
13) For jobs hereafter, support rear axle housing by using floor jack
under axle housing.
14) Remove differential carrier assembly.
15) Loosen rear mount nut of upper rod but don't remove bolt.
16) Loosen rear mount nut of lower rod but don't remove bolt.
17) Remove rear axle side lateral rod mount bolt.
18) Remove shock absorber lower mount bolt.
19) Lower floor jack until tension of suspension coil spring be-
comes a little loose and remove rear mount bolt of upper , lower
and lateral rod.
20) Lower rear axle housing gradually.
21) Remove axle housing.
Page 246 of 801
YH4
GRAND
VITARA
1. Lower rod
2. Body center
1. Rear axle housing
2. Spring seat
3. Coil spring
4. Stepped part
1. Axle housing ªAº 1. Body center
1
2
1
REAR SUSPENSION 3E-19
INSTALLATION
Install removed parts in reverse order of removal, noting the follow-
ing.
1) Place rear axle housing on floor jack. Then install upper / lower
rod rear mounting bolts (right & left) in proper direction as shown
(refer to UPPER ROD INSTALLATION for upper rod bolts). At
this time, mount nuts but don't tighten them.
2) Install coil spring (right & left) on spring seat of axle housing and
raise axle housing.
NOTE:
When seating coil spring, mate spring end with stepped
part of rear axle spring seat as shown.
3) Install lateral rod to rear axle housing.
4) Install lower part of shock absorber to right and left sides of axle
housing and install bolts in proper direction as shown in figure.
At this time, mount nuts but don't tighten them.
5) Clean mating surfaces of axle housing and differential carrier
and apply sealant to housing side.
ªAº: Sealant 99000-31110
6) Install differential carrier assembly to axle housing and tighten
carrier nuts to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
Page 263 of 801
YH4
GRAND
VITARA
1. Oil filler / level plug
2. Front drain plug
1. Circlip
2. Washer
1. Differential side joint
2. Tire lever
3. Front differential assembly
1. Oil seal 2
1
4A2-4 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
REMOVAL (RIGHT SIDE)
1) Hoist vehicle and remove wheel.
2) Drain differential gear oil.
3) Remove axle shaft drive flange.
4) Remove circlip and front spindle thrust washer.
5) Remove knuckle and wheel hub comp, refer to steps 5) to 7) and
9) to 14) of item COIL SPRING REMOVAL in Section 3D.
6) Remove drive shaft assembly.
To detach snap ring fitted on the spline of differential side joint
(inboard joint) from differential side gear, pull inboard joint by us-
ing a tire lever.
CAUTION:
To prevent breakage of boots (wheel side and differential
side), be careful not to bring them into contact with other
parts when removing drive shaft assembly.
7) Remove drive shaft thrust washer (to vehicle with G16 or J20 en-
gine) from drive shaft and remove drive shaft oil seal as shown
in figure.
CAUTION:
Be careful not to cause damage to drive shaft joint.
Page 280 of 801
YH4
GRAND
VITARA
5-4 BRAKES
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Not enough brak-
ing forceBrake oil leakage from brake lines.
Brake disc or pads stained with oil.
Overheated brakes.
Poor contact of shoes on brake drum.
Brake shoes linings stained with oil or wet
with water.
Badly worn brake shoe linings.
Defective wheel cylinders.
Malfunctioning caliper assembly.
Air in system.
Maladjusted sensor spring length of LSPV.
Broken sensor spring of LSPV.
Defective collar of LSPV.
Malfunctioning ABS (Antilock brake system),
if equipped.Locate leaking point and repair.
Clean or replace.
Determine cause and repair.
Repair for proper contact.
Replace.
Replace.
Repair or replace.
Repair or replace.
Bleed system.
Check or adjust.
Replace.
Replace.
Check system and replace as
necessary.
Brake pull
(Brakes not work-
ing in unison)Pad or shoe linings are wet with water or
stained with oil in some brakes.
Drum-to-shoe clearance out of adjustment in
some brakes.
(Malfunctioning auto adjusting mechanism)
Drum is out of round in some brakes.
Wheel tires are inflated unequally.
Malfunctioning wheel cylinders.
Disturbed front end alignment.
Unmatched tires on same axle.
Restricted brake pipes or hoses.
Malfunctioning caliper assembly.
Loose suspension parts.
Loose calipers.Replace.
Check for inoperative auto adjusting
mechanism.
Replace.
Inflate equally.
Repair or replace.
Adjust as prescribed.
Tires with approximately the same
amount of tread should be used on the
same axle.
Check for soft hoses and damaged
lines.
Replace with new hoses and new
brake pipes.
Check for stuck or sluggish pistons
and proper lubrication of caliper slide
bush.
Caliper should slide.
Check all suspension mountings.
Check and torque bolts to specifica-
tions.
Noise (High pitched
squeak without
brake applied)Front lining worn out.Replace linings.
Rear brake locked
prematurelyMaladjusted sensor spring length of LSPV.
Malfunction LSPV assembly.Check or adjust.
Replace assembly.
Brake locked
(For vehicles
equipped with
ABS)Malfunctioning ABS, if equipped.Check system and replace as
necessary.
Page 281 of 801
YH4
GRAND
VITARA
BRAKES 5-5
ConditionPossible CauseCorrection
Excessive pedal
travel (Pedal
stroke too large)Partial brake system failure.
Insufficient fluid in master cylinder
reservoirs.
Air in system. (pedal soft / spongy)
Rear brake system not adjusted.
(malfunctioning auto adjusting mechanism)
Bent brake shoes.
Worn rear brake shoes.Check brake systems and repair as
necessary.
Fill reservoirs with approved brake
fluid.
Check for leaks and air in brake
systems.
Check warning light. Bleed system if
required.
Bleed system.
Repair auto adjusting mechanism.
Adjust rear brakes.
Replace brake shoes.
Replace brake shoes.
Dragging brakes
(A very light drag
is present in all
disc brakes
immediately
after pedal is
released)Master cylinder pistons not returning
correctly.
Restricted brake pipes or hoses.
Incorrect parking brake adjustment on rear
brakes.
Weakened or broken return springs in the
brake.
Sluggish parking-brake cables or linkage.
Wheel cylinder or caliper piston sticking.
Malfunctioning ABS, if equipped with ABS.Replace master cylinder.
Check for soft hoses or damaged
pipes and replace with new hoses
and / or new brake pipes.
Check and adjust to correct specifi-
cations.
Replace.
Repair or replace.
Repair as necessary.
Check system and replace as
necessary.
Pedal pulsation
(Pedal pulsates
when depressed
for braking)Damaged or loose wheel bearings.
Distorted steering knuckle or rear axle
shafts.
Excessive disc lateral runout.
Parallelism not within specifications.
Rear drums out of round.Replace wheel hub component.
Replace knuckle or rear axle shaft.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check runout.
Repair or replace drum as
necessary.
Braking noiseGlazed shoe linings, or foreign matters
stuck to linings.
Worn or distorted shoe linings.
Loose front wheel bearings.
Distorted backing plates or loose mounting
bolts.Repair or replace shoe lining.
Replace shoe lining (or pad).
Replace wheel hub component.
Replace or retighten securing bolts.
