2003 SUZUKI GRAND VITARA HOSES
[x] Cancel search: HOSESPage 122 of 801
YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-51
G16 engine
J20 engine
H25 engine
3. Compressor pulley
4. Crankshaft pulley
INSTALLATION
FOR IWATA PRODUCTION VEHICLE
1) Pour new compressor oil. The amount must be the same with
the amount measured in REMOVAL.
NOTE:
Compressor assembly supplied from factory is filled up
with following amount of oil.
Amount of oil in compressor: 120 cm
3 (120 cc, 7.5 in3)
2)For G16 engine:
Install compressor assembly temporarily to bracket, then install
compressor drive belt (2).
For J20 and H25 engines:
Install compressor assembly to its bracket.
Tighten bolts (a) first, then (b).
Tightening Torque
(a), (b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Connect suction and discharge hoses to compressor assembly.
4)For G16 engine:
Tension compressor drive belt (2) by tightening compressor as-
sembly mounting bolts. Refer to Section 3B1 for drive belt ten-
sion.
Tighten bolt (a) first, then (b).
Tightening Torque
(a), (b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
For J20 engine:
Install generator belt (1). Refer to Section 6H for details.
For H25 engine:
Install compressor drive belt (2). Refer to Section 3B1 for instal-
lation and belt tension.
5) Connect thermal protector lead wire.
6) Evacuate and charge system according to previously described
procedure.
CAUTION:
Be sure to use HFC-134a (R-134a) compressor oil.
Page 123 of 801
YH4
GRAND
VITARA
1B-52 AIR CONDITIONING (OPTIONAL)
G16 engine
J20 engine
3. Compressor pulley
4. Crankshaft pulley
FOR CAMI PRODUCTION VEHICLE
1) Pour new compressor oil. The amount must be the same with
the amount measured in REMOVAL.
NOTE:
Compressor assembly supplied from factory is filled up
with the following amount of oil.
Amount of oil in compressor: 120 cm
3 (120 cc, 7.5 in3)
2)For G16 engine:
Install compressor assembly temporarily to bracket, then install
compressor drive belt (2).
For J20 engine:
Install compressor assembly to its bracket.
Tighten bolts (a).
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Connect suction and discharge hoses to compressor assembly.
4)For G16 engine:
Tension compressor drive belt (2) by tightening compressor as-
sembly mounting bolts. Refer to Section 3B1 for drive belt ten-
sion.
Tighten bolt (a) first, then (b).
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
For J20 engine:
Install generator belt (1). Refer to Section 6H for details.
5) Connect thermal protector lead wire.
6) Evacuate and charge system according to previously described
procedure.
CAUTION:
Be sure to use HFC-134a (R-134a) compressor oil.
Page 149 of 801
YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-5
DIAGNOSIS
GENERAL DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Steering wheel
feels heavy
(at low speed)Fluid deteriorated, low viscosity, different
type of fluid mixed
Pipes or hoses deformed, air entering
through joint
Insufficient air purging from P / S circuit
P / S belt worn, lacking in tension
Tire inflation pressure excessively low
Front end alignment out of order
Steering wheel installed improperly (twisted)
Bind in tie rod or tie rod end ball joint
P / S pump hydraulic pressure fails to increase
P / S pump hydraulic pressure increases
but slowly
Steering gear box malfunctionReplace fluid.
Replace defective part.
Purge air.
Adjust belt tension or replace
belt as necessary.
Inflate tire.
Check and adjust front end
alignment.
Install steering wheel correctly.
Replace defective part.
Check pressure and repair or
replace defective part.
Check pressure and repair or
replace defective part.
Replace gear box.
Steering wheel
feels heavy
momentarily when
turning it to the
left or rightAir drawn in due to insufficient amount
of fluid
Slipping P / S belt
P / S pump hydraulic pressure fails to
increase
P / S pump hydraulic pressure increases
but slowly
Steering gear box malfunctionAdd fluid and purge air.
Adjust belt tension or replace
belt as necessary.
Check pressure and repair or
replace defective part.
Check pressure and repair or
replace defective part.
Replace gear box.
Poor recovery
from turnsNOTE:
To check steering wheel for recovery, with vehicle running at 22 mile / h (35 km / h),
turn steering wheel 90 and let it free. It should return more than 60.
Deformed pipes or hoses
Steering column installed improperly
Front end alignment out of order
Ball joints binding
P / S pump hydraulic pressure fails to
increase
P / S pump hydraulic pressure increases
but slowly
Steering gear box malfunctionReplace defective part.
Install steering column correctly.
Check and adjust front end
alignment.
Replace defective part.
Check pressure and repair or
replace defective part.
Check pressure and repair or
replace defective part.
Replace gear box.
Page 150 of 801
YH4
GRAND
VITARA
3B1-6 POWER STEERING (P / S) SYSTEM
ConditionPossible CauseCorrection
Vehicle pulls to
one side during
straight drivingMismatched or uneven tire
Low or uneven tire inflation pressure
Brake dragging in one wheel
Front end alignment out of order
Rear end alignment out of order
Malfunction of control valve in gear boxReplace tire.
Inflate tires to proper pressure or
adjust right & left tires inflation
pressure.
Repair.
Check and adjust front end
alignment.
Check and adjust rear end
alignment.
Replace gear box.
Steering wheel
play is large and
vehicle wandersRefer to ªDiagnosisº in Section 3.
Fluid leakageLoose joints of (hydraulic pressure)
pipes and hoses
Deformed or damaged pipes or hosesRetighten.
Replace defective part.
Abnormal noiseAir drawn in due to insufficient amount of fluid
Air mixed into fluid from pipes or hoses
Slipping (loose) P / S belt
Worn P / S belt
Loose gear box fastening bolt
Loose linkage or joints
Pipes or hoses in contact with part of
vehicle body
Vanes of P / S pump defective
Malfunction of control valve in gear box
Bearing of P / S pump shaft defectiveAdd fluid and purge air.
Replace pipes or hoses.
Adjust belt tension.
Replace belt.
Retighten bolts.
Retighten.
Install pipes and hoses correctly.
Replace defective part.
Replace gear box.
Replace bearing.
No idle upPower steering pressure switch defectiveReplace power steering
pressure switch.
Page 279 of 801
YH4
GRAND
VITARA
BRAKES 5-3
SUBSTANDARD OR
CONTAMINATED BRAKE FLUID
Improper brake fluid, mineral oil or water in the fluid
may cause the brake fluid to boil or the rubber compo-
nents in the hydraulic system to deteriorate.
If primary piston cups are swollen, then rubber parts
have deteriorated. This deterioration may also be evi-
denced by swollen wheel cylinder piston cups on the
drum brake wheels.
If deterioration of rubber is evident, disassemble all
hydraulic parts and wash with alcohol. Dry these parts
with compressed air before assembly to keep alcohol
out of the system. Replace all rubber parts in the sys-
tem, including hoses. Also, when working on the
brake mechanisms, check for fluid on the linings. If ex-
cessive fluid is found, replace the linings.
If master cylinder piston seals are satisfactory, check
for leakage or excessive heat conditions. If condition
is not found, drain fluid, flush with brake fluid, refill and
bleed system.
The system must be flushed if there is any doubt as
to the grade of fluid in the system or if fluid has been
used which contained parts that have been subjected
to contaminated fluid.
DIAGNOSIS
ROAD TESTING BRAKES
Brakes should be tested on dry, clean, smooth and
reasonably level roadway which is not crowned. Road
test brakes by making brake applications with both
light and heavy pedal forces at various speeds to de-
termine if the vehicle stops evenly and effectively.
Also drive vehicle to see if it leads to one side or the
other without brake application. If it does, check the
tire pressure, front end alignment and front suspen-
sion attachments for looseness. See diagnosis chart
for other causes.
BRAKE FLUID LEAKS
Check the master cylinder fluid levels. While a slight
drop in reservoir level does result from normal lining
wear, an abnormally low level indicates a leak in the
system. In such a case, check the entire brake system
for leakage. If even a slight evidence of leakage is
noted, the cause should be corrected or defective
parts should be replaced.
If fluid level is lower than the minimum level of reser-
voir, refilling is necessary. Fill reservoir with specified
brake fluid.
Brake fluid: Refer to reservoir tank cap.
CAUTION:
Since brake system of this vehicle is factory-
filled with brake fluid indicated on reservoir
tank cap, do not use or mix different type of
fluid when refilling; otherwise serious damage
will occur.
Do not use old or used brake fluid, or any fluid
from a unsealed container.
Page 280 of 801
YH4
GRAND
VITARA
5-4 BRAKES
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Not enough brak-
ing forceBrake oil leakage from brake lines.
Brake disc or pads stained with oil.
Overheated brakes.
Poor contact of shoes on brake drum.
Brake shoes linings stained with oil or wet
with water.
Badly worn brake shoe linings.
Defective wheel cylinders.
Malfunctioning caliper assembly.
Air in system.
Maladjusted sensor spring length of LSPV.
Broken sensor spring of LSPV.
Defective collar of LSPV.
Malfunctioning ABS (Antilock brake system),
if equipped.Locate leaking point and repair.
Clean or replace.
Determine cause and repair.
Repair for proper contact.
Replace.
Replace.
Repair or replace.
Repair or replace.
Bleed system.
Check or adjust.
Replace.
Replace.
Check system and replace as
necessary.
Brake pull
(Brakes not work-
ing in unison)Pad or shoe linings are wet with water or
stained with oil in some brakes.
Drum-to-shoe clearance out of adjustment in
some brakes.
(Malfunctioning auto adjusting mechanism)
Drum is out of round in some brakes.
Wheel tires are inflated unequally.
Malfunctioning wheel cylinders.
Disturbed front end alignment.
Unmatched tires on same axle.
Restricted brake pipes or hoses.
Malfunctioning caliper assembly.
Loose suspension parts.
Loose calipers.Replace.
Check for inoperative auto adjusting
mechanism.
Replace.
Inflate equally.
Repair or replace.
Adjust as prescribed.
Tires with approximately the same
amount of tread should be used on the
same axle.
Check for soft hoses and damaged
lines.
Replace with new hoses and new
brake pipes.
Check for stuck or sluggish pistons
and proper lubrication of caliper slide
bush.
Caliper should slide.
Check all suspension mountings.
Check and torque bolts to specifica-
tions.
Noise (High pitched
squeak without
brake applied)Front lining worn out.Replace linings.
Rear brake locked
prematurelyMaladjusted sensor spring length of LSPV.
Malfunction LSPV assembly.Check or adjust.
Replace assembly.
Brake locked
(For vehicles
equipped with
ABS)Malfunctioning ABS, if equipped.Check system and replace as
necessary.
Page 281 of 801
YH4
GRAND
VITARA
BRAKES 5-5
ConditionPossible CauseCorrection
Excessive pedal
travel (Pedal
stroke too large)Partial brake system failure.
Insufficient fluid in master cylinder
reservoirs.
Air in system. (pedal soft / spongy)
Rear brake system not adjusted.
(malfunctioning auto adjusting mechanism)
Bent brake shoes.
Worn rear brake shoes.Check brake systems and repair as
necessary.
Fill reservoirs with approved brake
fluid.
Check for leaks and air in brake
systems.
Check warning light. Bleed system if
required.
Bleed system.
Repair auto adjusting mechanism.
Adjust rear brakes.
Replace brake shoes.
Replace brake shoes.
Dragging brakes
(A very light drag
is present in all
disc brakes
immediately
after pedal is
released)Master cylinder pistons not returning
correctly.
Restricted brake pipes or hoses.
Incorrect parking brake adjustment on rear
brakes.
Weakened or broken return springs in the
brake.
Sluggish parking-brake cables or linkage.
Wheel cylinder or caliper piston sticking.
Malfunctioning ABS, if equipped with ABS.Replace master cylinder.
Check for soft hoses or damaged
pipes and replace with new hoses
and / or new brake pipes.
Check and adjust to correct specifi-
cations.
Replace.
Repair or replace.
Repair as necessary.
Check system and replace as
necessary.
Pedal pulsation
(Pedal pulsates
when depressed
for braking)Damaged or loose wheel bearings.
Distorted steering knuckle or rear axle
shafts.
Excessive disc lateral runout.
Parallelism not within specifications.
Rear drums out of round.Replace wheel hub component.
Replace knuckle or rear axle shaft.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check runout.
Repair or replace drum as
necessary.
Braking noiseGlazed shoe linings, or foreign matters
stuck to linings.
Worn or distorted shoe linings.
Loose front wheel bearings.
Distorted backing plates or loose mounting
bolts.Repair or replace shoe lining.
Replace shoe lining (or pad).
Replace wheel hub component.
Replace or retighten securing bolts.
Page 386 of 801
YH4
GRAND
VITARA
Viscosity chart
SAE
1. Reverse idle gear shaft bolt
(DO NOT LOOSEN IT)
MANUAL TRANSMISSION (TYPE 1) 7A-3
ON-VEHICLE SERVICE
GEAR OIL
INSPECTION AND CHANGE
1) Before changing or inspecting oil, be sure to stop engine and lift
vehicle horizontally.
2) With vehicle lifted up, check oil level and leakage. If leakage ex-
ists, correct or repair it.
3) Drain old oil and fill new specified oil as shown below by speci-
fied amount (roughly up to level hole).
NOTE:
It is highly recommended to use SAE 75W-90 gear oil.
Whenever vehicle is hoisted for any other service work
than oil change, also be sure to check for oil leakage and
status of breather hoses.
If water or rust is mixed in drained oil, be sure to check
breather hose and boot of transmission and transfer.
Gear Oil Specification
Oil grade: API GL-4
Viscosity: SAE 75W-85, 75W-90 or 80W-90
Oil Capacity:
Transmission 1.5 liters (3.2 / 2.6 US / Imp. pt)
Transfer 1.7 liters (3.6 / 3.0 US / Imp. pt)
4) Torque drain plug and level / filler plug as specified below after
applying sealant to its thread.
CAUTION:
Transmission oil must not be poured through gear shift
control lever part.
Do not loosen or remove reverse idle gear shaft bolt.
ªAº: Sealant 99000-31110
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)