2003 SUZUKI GRAND VITARA Transfer case oil

YH4
GRAND
VITARA
1. Match mark
1. Transfer rear case
2. Oil seal
ªAº
ªBº
TRANSFER 7D-3
ON-VEHICLE SERVICE
GEAR OIL
Refer to ªON-VEHICLE SERVICEº of Section 7A or 7A1.
TRANSFER OIL SEALS
REAR CASE OIL SEAL
1) Lift up vehicle horizontally.
2) Give match marks on joint flange and propeller shaft as shown
in figure.
3) Remove 4 bolts from rear propeller shaft flange and remove pro-
peller shaft.
4) Using screwdriver, remove oil seal.
5) Using special tool(A) and plastic hammer, pressfit new oil seal
up to case surface. Be sure to apply grease to oil seal lip.
ªAº: Grease 99000-25010
Special Tool
(A): 09940-53111
6) Clean and inspect sliding portion of propeller shaft front end
(where oil seal contacts) before installation and if even small
dent or scratch exists, correct and clean it again.
Then apply grease inside splines of propeller shaft.
ªBº: Grease 99000-25010
7) Install propeller shaft and torque universal joint flange bolts to
specification.
CAUTION:
Be sure to use only specified bolts, nuts and lock wash-
ers for universal joint flange.
Tightening Torque:
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
CENTER CASE OIL SEAL (Front side)
In addition to the procedure for rear case oil seal, it is necessary to
drain and refill gear oil of transfer. Refer to Section 7A ªON-VE-
HICLE SERVICEº for oil specification.

YH4
GRAND
VITARA
1. Wood block
2. Dash panel
t: 45 mm / 1.8 in.
H: 200 mm / 8 in.
W: 100 ± 150 mm / 4 ± 6 in.
1. Transmission jack
2. Engine rear mounting member
3. Gear shift lever case
4. Bolt
TRANSFER 7D-5
TRANSFER ASSEMBLY
Dismounting and remounting of transfer and transmission together
as a unit is described in Section 7A for Manual Transmission or 7B1
for Automatic Transmission, but it is also possible to dismount and
remount transfer assembly by itself as described below.
DISMOUNTING
IN ENGINE ROOM
1) Disconnect negative (±) cable from battery.
2) Remove distributor assembly (if equipped).
3) Place wood block between engine and dash panel so that it
serves as stopper when engine, transmission and transfer unit
hangs down as rear mounting member is removed.
CAUTION:
Make sure to use wood block to prevent contact which
may occur between dash panel and CMP sensor case
(G16), CMP sensor (J20) or intake manifold (H25), and fan
and shroud.
IN CABIN
1) Remove console box.
2) Remove shift lever of transmission and transfer.
ON LIFT
1) Drain transfer oil.
2) Remove rear propeller shaft.
3) Remove front propeller shaft.
4) Disconnect exhaust center pipe.
5) Disconnect speed sensor coupler.
6) Place transmission jack and remove mounting member.
7) Lower transmission jack gradually and check to ensure that
wood block serves as stopper between engine and dash panel.
8) Remove bolts for gear shift lever case.
9) Pull off breather hose.

YH4
GRAND
VITARA
1. Bolt
2. Transfer assembly
1. Bolt
2. Engine rear mounting3. Transfer assembly
1. Bolt
2. Transfer assembly
3. Transmission jack
7D-6 TRANSFER
IN CABIN
Remove gear shift lever case and then remove transfer center case
bolt.
ON LIFT
1) Remove transfer mounting (engine rear mounting) by removing
bolts.
2) Apply transmission jack to transfer to support it.
3) Remove couplers for 4WD / 4WD-LOW switches lead.
4) Remove transfer front case bolts.
5) With transfer assembly supported with transmission jack, slide
it rearward and when it is apart from transmission, lower it.
REMOUNTING
For remounting, reverse dismounting procedure described above,
noting following.

Be sure to use specified torque for tightening.

Clamp wiring and breather hose securely.

Clamp shift lever boot securely.

Fill specified gear oil by specified amount.

Connect battery and check for function.